Skip to contentSkip to conversation

Statistics

LARTC Ethy H. Brito 8 participants 9 messages Dec 21, 2001 – Sep 4, 2003

lore
Share & tools
lore
#0 lore raw

Dear Guru

What are the meanings of the statistic fields? For example:

qdisc tbf 8020: rate 256Kbit burst 10Kb lat 190.7ms
Sent 941500 bytes 11288 pkts (dropped 33, overlimits 0) backlog 770b 9p

qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit Sent 969153 bytes 11632 pkts (dropped 33, overlimits 22419) backlog 9p
borrowed 0 overactions 0 avgidle 624 undertime 0

What "dropped 33" means? Packets I presume.
"Overlimits 22419"? What this mean? Were all these bytes discarded? Backlog? What is this?

Any1 could point some documentation about statistic fields?

Thanks a lot.

Ethy H. Brito /"\
InterNexo Ltda. \ / CAMPANHA DA FITA ASCII - CONTRA MAIL HTML
+55 (12) 3941-6860 X ASCII RIBBON CAMPAIGN - AGAINST HTML MAIL
S.J.Campos - Brasil / \

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#1 lore raw
Quoted 7 lines · Ethy H. Brito

Dear Guru

What are the meanings of the statistic fields? For example:

qdisc tbf 8020: rate 256Kbit burst 10Kb lat 190.7ms
Sent 941500 bytes 11288 pkts (dropped 33, overlimits 0)

941500 bytes and 11288 were actually sent, and not dropped. 33 packets were dropped.

Quoted 1 line

backlog 770b 9p

9 packets are waiting to be allowed to be sent, totalling 770 bytes.

Quoted 2 lines

qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit Sent 969153 bytes 11632 pkts (dropped 33, overlimits 22419)

22419 times did cbq throttle itself because it was exceeding its rate.

Quoted 2 lines

backlog 9p
borrowed 0 overactions 0 avgidle 624 undertime 0

avgidle is described in the manpages on ds9a.nl/lartc/manpages

Regards,

bert

Signature · 8 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
http://www.tk                              the dot in .tk
Netherlabs BV / Rent-a-Nerd.nl           - Nerd Available -
Linux Advanced Routing & Traffic Control: http://ds9a.nl/lartc

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
#2 lore raw
In reply to Ethy H. Brito

Hi all,

I'm experimenting with HTB and IMQ and I'm wondering if there exists a tool to graph the throughput of traffic through my router.
I now I can setup iptables to count packets and read/reset these with a script , but maybe there is allready something MRTG alike but for shorter periods of measurements.

Thanks alot,

Signature · 14 lines
* Bart Duchesne * R&D Engineer
*
* Able NV
* Leuvensesteenweg 282 - B-3190 Boortmeerbeek - Belgium
* Phone: + 32 15 50.44.00 - Fax: + 32 15 50.44.09
* E-Mail: [email protected]
* URL: http://www.axsguard.com
*



--
Security check on this e-mail has been done by aXs GUARD
(http://www.axsguard.com)
#3 lore raw
In reply to Ethy H. Brito
Quoted 7 lines · Bart Duchesne

Hi all,

I'm experimenting with HTB and IMQ and I'm wondering if there exists a tool to graph the throughput of traffic through my router.
I now I can setup iptables to count packets and read/reset these with a script , but maybe there is allready something MRTG alike but for shorter periods of measurements.

Try with 'monitor*' at www.docum.org Stef Coene's website about Traffic Control.

Quoted 20 lines

Thanks alot,

Signature · 15 lines
* Bart Duchesne 
* R&D Engineer
*
* Able NV
* Leuvensesteenweg 282 - B-3190 Boortmeerbeek - Belgium
* Phone: + 32 15 50.44.00 - Fax: + 32 15 50.44.09
* E-Mail: [email protected]
* URL: http://www.axsguard.com
*



--
Security check on this e-mail has been done by aXs GUARD
(http://www.axsguard.com)
Signature · 10 lines
--

Daniel Ortiz
[email protected]

ILIMIT Comunicacions
Departament Sistemes
http://www.ilimit.es
Tel: (+34) 93 733 33 75
Fax: (+34) 93 733 32 43
#4 lore raw
In reply to Ethy H. Brito

: I'm experimenting with HTB and IMQ and I'm wondering if there exists a : tool to graph the throughput of traffic through my router.
: I now I can setup iptables to count packets and read/reset these with a : script , but maybe there is allready something MRTG alike but for : shorter periods of measurements.

See Stef's rrdtool-based tools [1] or if you need something more like real-time stats, the Java-based stuff [2], or even his perl tools [3].

-Martin

[1] http://www.docum.org/stef.coene/qos/gui/
[2] http://www.docum.org/stef.coene/qos/java/
[3] http://www.docum.org/stef.coene/qos/monitor/

Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#5 lore raw
In reply to Ethy H. Brito
Quoted 7 lines · Bart Duchesne

Hi all,

I'm experimenting with HTB and IMQ and I'm wondering if there exists a tool to graph the throughput of traffic through my router.
I now I can setup iptables to count packets and read/reset these with a script , but maybe there is allready something MRTG alike but for shorter periods of measurements.

You might find my snmprtg useful for this, but you will need to be able to query it using SNMP. It can run on most platforms too. Its still very young, but quite usable. Currently the Poll Interval, and the number of minutes to display is hard coded (5 secs, 10 mins respectively), but should be easily changed.

http://nzgeeks.org/cameron/progs/snmprtg.php

Runs on anything with Perl/Tk and the SNMP module. (Developed on Linux, tested with Windows NT and ActiveState Perl)

Signature · 7 lines
Cameron Kerr
Email:   [email protected]
Website: http://nzgeeks.org/cameron/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#6 lore raw
In reply to Ethy H. Brito

Helle everybody,

I am finishing a computer science degree and I would like to know how you use qos on Linux.

Please take a few seconds to answer my questions

I would like to know :
- what type of qdisc you use
- if it is only for tests or for a "real" use (what use)
- how much qos box do you use
- do you use anything else (Cisco, Unix ...)

I don't know if it is better that you answer to me or to the list, so do as you want. Anyway i will send the result to the list.

Thanks in advance
Emmanuel

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#7 lore raw
In reply to Ethy H. Brito

Hello, Emmanuel,

Straight to the question:

1. Personally I'm using mostly HTB.
2. Yes, it is in real use - that way I'm controlling traffic in the ISP I'm working in.
3. I didnt get this question. If you're asking about the HW parameters - PIII/1Ghz. If you're asking about the quantity of QOS boxen I'm using - 5 of them, 4 GNU/Linux and one FreeBSD.
4. Yes, I'm using Cisco policers, but not for smth serious. Besides I'm using FreeBSD altq with CBQ as a shaper (cause that's what it is).

On Thu, 4 Sep 2003 22:56:02 +0200
"Emmanuel SIMON" <[email protected]> wrote:

: Helle everybody,
:
: I am finishing a computer science degree and I would like to know how you : use qos on Linux.
:
: Please take a few seconds to answer my questions
:
: I would like to know :

 :  - what type of qdisc you use
 :  - if it is only for tests or for a "real" use (what use)
 :  - how much qos box do you use
 :  - do you use anything else (Cisco, Unix ...)

:
: I don't know if it is better that you answer to me or to the list, so do as : you want. Anyway i will send the result to the list.
:
: Thanks in advance
: Emmanuel

Signature · 7 lines
Със здраве,
Никола
_____________________________________________________________

"Engineering does not require science. Science helps a lot but
people built perfectly good brick walls long before they knew
why cement works."	-Alan Cox 	
#8 lore raw
In reply to Ethy H. Brito

allready 2 answers, thank you
the 3rd question don't seem clear :
- I am not asking about the HW parameters, but about the quantity of QOS
boxen you are using

thx for the 2 first and please go on

Quoted 27 lines

-----Message d'origine-----
De : [email protected]
[mailto:[email protected]]De
la part de Emmanuel SIMON
Envoyé : jeudi 4 septembre 2003 22:56
À : 'LARTC'
Objet : [LARTC] Statistics

Helle everybody,

I am finishing a computer science degree and I would like to know how you
use qos on Linux.

Please take a few seconds to answer my questions

I would like to know :
- what type of qdisc you use
- if it is only for tests or for a "real" use (what use)
- how much qos box do you use
- do you use anything else (Cisco, Unix ...)

I don't know if it is better that you answer to me or to the list, so do as
you want. Anyway i will send the result to the list.

Quoted 7 lines

Thanks in advance
Emmanuel

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/