Skip to contentSkip to conversation

Confusion about kernelconfig QoS-options

LARTC Nils Lichtenfeld 2 participants 5 messages Aug 29, 2002

lore
Share & tools
lore
#0 lore raw

Hello there!

Using Kernel 2.4.19.

The modules I intend to use are SFQ queue, HTB packet scheduler, Firewall based classifier and the U32 classifier.

Witch of the following options _NEED_ to be enabled? I ask, because the goal is to have the kernel as small as possible.

< QOS and/or fair queueing >
[*] QoS support
[*] Rate estimator

[*] Traffic policing

Thank you!
Greetings, Nils

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 9 lines · Nils Lichtenfeld

Hello there!

Using Kernel 2.4.19.

The modules I intend to use are SFQ queue, HTB packet scheduler, Firewall based classifier and the U32 classifier.

Witch of the following options _NEED_ to be enabled? I ask, because the goal is to have the kernel as small as possible.

Then use modules and load only the modules you need.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Nils Lichtenfeld

Hi Stef!

Quoted 3 lines · Stef Coene
Quoted 2 lines

Witch of the following options _NEED_ to be enabled? I ask, because the goal is to have the kernel as small as possible.

Then use modules and load only the modules you need.

That was not my question. The listed items are not selectable as modules. They can only be compiled into the kernel or turned off. I list them again, they reside in the < QOS and/or fair queueing > section:

[*] QoS support
[*] Rate estimator

[*] Traffic policing

"*" is the default selection.

Thank you!
Greetings, Nils

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Nils Lichtenfeld
Quoted 6 lines · Nils Lichtenfeld

Hi Stef!

Quoted 3 lines · Stef Coene
Quoted 2 lines

Witch of the following options _NEED_ to be enabled? I ask, because the goal is to have the kernel as small as possible.

Quoted 7 lines
Quoted 1 line

Then use modules and load only the modules you need.

That was not my question. The listed items are not selectable as modules. They can only be compiled into the kernel or turned off. I list them again, they reside in the < QOS and/or fair queueing > section:

[*] QoS support

Only needed if you want to implement QOS support so other devices on the network can send requestst for bandwidth.

Quoted 1 line

[*] Rate estimator

This can be used for the "Traffic policing" to calculate the rate of the packets.

Quoted 1 line

[*] Traffic policing

This is sort of tbf-in-filter. You can configure a filter to only match packets at a certain rate.

You don't need these options to use SFQ, HTB, fw and/or u32.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#4 lore raw
In reply to Nils Lichtenfeld

Hello Stef!

Quoted 11 lines · Stef Coene
Quoted 6 lines · Nils Lichtenfeld

That was not my question. The listed items are not selectable as modules. They can only be compiled into the kernel or turned off. I list them again, they reside in the < QOS and/or fair queueing > section:

[*] QoS support

Only needed if you want to implement QOS support so other devices on the network can send requestst for bandwidth.

Quoted 1 line

[*] Rate estimator

Quoted 8 lines

This can be used for the "Traffic policing" to calculate the rate of the packets.

Quoted 1 line

[*] Traffic policing

This is sort of tbf-in-filter. You can configure a filter to only match packets at a certain rate.

You don't need these options to use SFQ, HTB, fw and/or u32.

Thank you very, very mutch! This is exactly the information I was hoping for.

Greetings, Gundy

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/