does tc support mpls ?
hi everybody,
i just want to know if tc provides any bandwidth management through the tc_index field of the sk_buff or the exp bits of the shim header in an mpls cloud ? if so ,how it is done?
ashutosh.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
HELLO ALL,
I WILL BE VERY HAPPY IS ANY BODY ON THISLIST CAN TELL ME HOW TO SET MY ETHERNET LAN SPEED TO 10MBPS ON A REDHAT BOX.
THANKS
GOKE
NEWBIE
Ashutosh Pattanaik <[email protected]> wrote:
hi everybody,
i just want to know if tc provides any bandwidth management through the tc_index field of the sk_buff or the exp bits of the shim header in an mpls cloud ? if so ,how it is done?
ashutosh.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
---------------------------------
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
I assume that your current ethernet card speed is 100 Mbit/s
Just do
mii-tool eth0 -A 10BaseT
and this will set your card to 10BaseT-only speeds.
If you get an error, your card does not support MII.
And, at last, this is not the right maillist for this question.
-- Nikolay Datchev
Quoted 18 lines · olagoke Metibemu
HELLO ALL,
I WILL BE VERY HAPPY IS ANY BODY ON THISLIST CAN TELL ME HOW TO SET MY ETHERNET LAN SPEED TO 10MBPS ON A REDHAT BOX.THANKS
GOKE
NEWBIEAshutosh Pattanaik <[email protected]> wrote:
hi everybody,
i just want to know if tc provides any bandwidth management through thetc_indexfield of thesk_buffor the exp bits of the shim header in an mpls cloud ? if so ,how it is done?
ashutosh.
Quoted 8 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/---------------------------------
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 5 lines · Nikolay Datchev
I assume that your current ethernet card speed is 100 Mbit/s
Just do
mii-tool eth0 -A 10BaseT
Or you could do,
tc qdisc add dev ethX root tbf rate 10Mbit latency 50ms burst 1540
(I'm really not sure about latency and burst, because I usually have the rate set at 220kbit. YMMV).
Quoted 11 lines
-- Nikolay Datchev
Quoted 7 lines · olagoke Metibemu
HELLO ALL,
I WILL BE VERY HAPPY IS ANY BODY ON THISLIST CAN TELL ME HOW TO SET MY ETHERNET LAN SPEED TO 10MBPS ON A REDHAT BOX.THANKS
GOKE
NEWBIE
Regards,
Brad Lay ( brad /at/ coombabah.net )
"I used to be indecisive, now I'm not so sure."
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 51 lines
--__--__--
Message: 2
Date: Sat, 28 Jun 2003 15:51:14 +1000 (EST)
From: Brad Lay <[email protected]>
To: Nikolay Datchev <[email protected]>
Cc: olagoke Metibemu <[email protected]>,
Ashutosh Pattanaik <[email protected]>, [email protected]
Subject: Re: [LARTC] does tc support mpls ?Quoted 7 lines · Nikolay Datchev
I assume that your current ethernet card speed is 100 Mbit/s
Just do
mii-tool eth0 -A 10BaseT
Or you could do,
tc qdisc add dev ethX root tbf rate 10Mbit latency 50ms burst 1540(I'm really not sure about latency and burst, because I usually have the rate set at 220kbit. YMMV).
Quoted 15 lines
-- Nikolay Datchev
Quoted 9 lines · olagoke Metibemu
HELLO ALL,
I WILL BE VERY HAPPY IS ANY BODY ON THISLIST CAN TELL ME HOW TO SET MY ETHERNET LAN SPEED TO 10MBPS ON A REDHAT BOX.THANKS
GOKE
NEWBIERegards,
Quoted 10 lines
Brad Lay ( brad /at/ coombabah.net )
"I used to be indecisive, now I'm not so sure."
--__--__--
You can use ethtool to set your ethernet speed, by using the following command
ethtool -s ethX [speed 10|100|1000] [duplex half|full]
ethtool is available over the Web on the SourceForge site at http://sourceforge.net/projects/gkernel/
-Srikanth.