Skip to contentSkip to conversation

does tc support mpls ?

LARTC Ashutosh Pattanaik 5 participants 5 messages Jun 27, 2003 – Jun 30, 2003

lore
Share & tools
lore
#1 lore raw

HELLO ALL,
I WILL BE VERY HAPPY IS ANY BODY ON THISLIST CAN TELL ME HOW TO SET MY ETHERNET LAN SPEED TO 10MBPS ON A REDHAT BOX.

THANKS

GOKE
NEWBIE

Ashutosh Pattanaik <[email protected]> wrote:
hi everybody,
i just want to know if tc provides any bandwidth management through the tc_index field of the sk_buff or the exp bits of the shim header in an mpls cloud ? if so ,how it is done?
ashutosh.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

---------------------------------
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!

#2 lore raw
In reply to Ashutosh Pattanaik

I assume that your current ethernet card speed is 100 Mbit/s

Just do

mii-tool eth0 -A 10BaseT

and this will set your card to 10BaseT-only speeds.

If you get an error, your card does not support MII.

And, at last, this is not the right maillist for this question.

-- Nikolay Datchev

Quoted 18 lines · olagoke Metibemu

HELLO ALL,
I WILL BE VERY HAPPY IS ANY BODY ON THISLIST CAN TELL ME HOW TO SET MY ETHERNET LAN SPEED TO 10MBPS ON A REDHAT BOX.

THANKS

GOKE
NEWBIE

Ashutosh Pattanaik <[email protected]> wrote:
hi everybody,
i just want to know if tc provides any bandwidth management through the tc_index field of the sk_buff or the exp bits of the shim header in an mpls cloud ? if so ,how it is done?
ashutosh.

Quoted 8 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

---------------------------------
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Ashutosh Pattanaik
Quoted 5 lines · Nikolay Datchev

I assume that your current ethernet card speed is 100 Mbit/s

Just do

mii-tool eth0 -A 10BaseT

Or you could do,
tc qdisc add dev ethX root tbf rate 10Mbit latency 50ms burst 1540

(I'm really not sure about latency and burst, because I usually have the rate set at 220kbit. YMMV).

Quoted 11 lines

-- Nikolay Datchev

Quoted 7 lines · olagoke Metibemu

HELLO ALL,
I WILL BE VERY HAPPY IS ANY BODY ON THISLIST CAN TELL ME HOW TO SET MY ETHERNET LAN SPEED TO 10MBPS ON A REDHAT BOX.

THANKS

GOKE
NEWBIE

Regards,

Brad Lay ( brad /at/ coombabah.net )

W) http://coombabah.net/

"I used to be indecisive, now I'm not so sure."
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to Ashutosh Pattanaik
Quoted 51 lines

--__--__--

Message: 2
Date: Sat, 28 Jun 2003 15:51:14 +1000 (EST)
From: Brad Lay <[email protected]>
To: Nikolay Datchev <[email protected]>
Cc: olagoke Metibemu <[email protected]>,
Ashutosh Pattanaik <[email protected]>, [email protected]
Subject: Re: [LARTC] does tc support mpls ?

Quoted 7 lines · Nikolay Datchev

I assume that your current ethernet card speed is 100 Mbit/s

Just do

mii-tool eth0 -A 10BaseT

Or you could do,
tc qdisc add dev ethX root tbf rate 10Mbit latency 50ms burst 1540

(I'm really not sure about latency and burst, because I usually have the rate set at 220kbit. YMMV).

Quoted 15 lines

-- Nikolay Datchev

Quoted 9 lines · olagoke Metibemu

HELLO ALL,
I WILL BE VERY HAPPY IS ANY BODY ON THISLIST CAN TELL ME HOW TO SET MY ETHERNET LAN SPEED TO 10MBPS ON A REDHAT BOX.

THANKS

GOKE
NEWBIE

Regards,

Quoted 10 lines

Brad Lay ( brad /at/ coombabah.net )

W) http://coombabah.net/

"I used to be indecisive, now I'm not so sure."

--__--__--

You can use ethtool to set your ethernet speed, by using the following command

ethtool -s ethX [speed 10|100|1000] [duplex half|full]

ethtool is available over the Web on the SourceForge site at http://sourceforge.net/projects/gkernel/

-Srikanth.