IP Telephony with HTB or IMQ
Hello all,
Please, does anyone have a setup where HTB or IMQ was used to set aside uplink/downlink speed for IP Telephony, in other to have clear voice quality?
K
_________________________________________________________________
Add photos to your messages with MSN 8. Get 2 months FREE*.
http://join.msn.com/?pageþatures/featuredemail
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Don't expect good quality if use local QoS for incomming data. To have real non-best effort you need to have QoS on both sides of link - when transmitting packets. Then yes - HTB should be able to do it using priorities. But I doubd you can do it if IMQ is in the way. devik
Quoted 8 lines · Chijioke Kalu
Hello all,
Please, does anyone have a setup where HTB or IMQ was used to set aside uplink/downlink speed for IP Telephony, in other to have clear voice quality?
K
Quoted 10 lines
_________________________________________________________________
Add photos to your messages with MSN 8. Get 2 months FREE*.
http://join.msn.com/?pageþatures/featuredemail_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Ok by me, am just desperate, after reading the documentation and tried differing configs, i was not successful, thus decided to ask experts, I will wait till monday
thank you
--------------------------------
Sorry I answer some mails if it is under 30seconds or so. I have no time to write/test such config but I'm sure someone will do it at least at Monday.
devik
Quoted 3 lines · Chijioke Kalu
Hi Devik,
this could be asking too much, ave just finished compiling kernel with
htb
Quoted 1 line
patch, and the htb is functioning, do you mind giving me a sample config
I
Quoted 23 lines
can use to achieve this, if it aint too much of a bother.
which setup do u prefer:
Setup A
eth0 - Internet
eth1 - 20 LAN computers + 1 IP TelephonySetup B
eth0 - Internet
eth1 - 20 LAN Computers
eth2 - 1 IP TelephonyAny choice u make is ok with me, I would just like to see your working sample HTB script.
Thanks
K
Quoted 12 lines
Don't expect good quality if use local QoS for incomming data. To have real non-best effort you need to have QoS on both sides of link - when transmitting packets. Then yes - HTB should be able to do it using priorities. But I doubd you can do it if IMQ is in the way. devik
Quoted 3 lines · Chijioke Kalu
Hello all,
Please, does anyone have a setup where HTB or IMQ was used to set
aside
Quoted 16 lines
Quoted 5 lines
uplink/downlink speed for IP Telephony, in other to have clear voice quality?
K
Quoted 10 lines
_________________________________________________________________
Add photos to your messages with MSN 8. Get 2 months FREE*.
http://join.msn.com/?pageþatures/featuredemail_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 7 lines
_________________________________________________________________
STOP MORE SPAM with the new MSN 8 and get 2 months FREE*
http://join.msn.com/?pageþatures/junkmail
_________________________________________________________________
STOP MORE SPAM with the new MSN 8 and get 2 months FREE*
http://join.msn.com/?pageþatures/junkmail
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Yes if you consider transmission over internet. Unfortunately it is mostly best effort medium and workable VoIP is possible mainly because of huge BW after user's access line .. And there is still no compatible Diffserv marking working over whole Internet.
Quoted 45 lines · On Sat, 5 Jul 2003, Gerry Creager N5JXS wrote:
In fact, it's more complicated than Devik offers. QoS should be set, AND compatible marking taking place on both sides of the link as stated.
However, while it's extremely important that both participating
networks agree on marking and queuing, if the ISPs and carriers are congested and do not participate in mark recognition and appropriate queuing. it falls back to a best effort, lossy network, regardless of what you do at the edges.gerry
Quoted 30 lines · Martin Devera
Don't expect good quality if use local QoS for incomming data. To have real non-best effort you need to have QoS on both sides of link - when transmitting packets. Then yes - HTB should be able to do it using priorities. But I doubd you can do it if IMQ is in the way. devik
Quoted 8 lines · Chijioke Kalu
Hello all,
Please, does anyone have a setup where HTB or IMQ was used to set aside uplink/downlink speed for IP Telephony, in other to have clear voice quality?
K
Quoted 10 lines
_________________________________________________________________
Add photos to your messages with MSN 8. Get 2 months FREE*.
http://join.msn.com/?pageþatures/featuredemail_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/Quoted 3 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 10 lines
--
Gerry Creager -- [email protected]
Network Engineering -- AATLT, Texas A&M University
Cell: 979.229.5301 Office: 979.458.4020 FAX: 979.847.8578
Page: 979.228.0173
Office: 903A Eller Bldg, TAMU, College Station, TX 77843
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/