Bandwith sharing in NAT environment.
Hi
I wish to implement Bandwith sharing in a NAT environment.
The question is whether I can classify input packets on the basis of ip-addresses (private LAN addresses)? These packets finally need to be NATed before going on to Internet.
Would the tc filters see the private addresses and put it in the appropriate classes or would the tc filters see only the NATed address and the filter would fail in putting the packets in the appropriate classes?
The n/w diag would be somewhat like this
private address LAN ips ------>iptables(NAT)------>Internet.
Can I mark packets using iptables matching source ip-address? What address will tc filter see when the private addresses are masqueraded ?
Any help is most welcome.
Cheers,
Rajesh
_______________________________________________
No banners. No pop-ups. No kidding.
Introducing My Way - http://www.myway.com
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 12 lines · Rajesh
Hi
I wish to implement Bandwith sharing in a NAT environment.
The question is whether I can classify input packets on the basis of ip-addresses (private LAN addresses)? These packets finally need to be NATed before going on to Internet.
Would the tc filters see the private addresses and put it in the appropriate classes or would the tc filters see only the NATed address and the filter would fail in putting the packets in the appropriate classes?
Quoted 5 lines
The n/w diag would be somewhat like this
private address LAN ips ------>iptables(NAT)------>Internet.
Can I mark packets using iptables matching source ip-address?
Yes.
Quoted 2 lines
What address will tc filter see when the private addresses are masqueraded ?
The ip address of your firewall. So you have to mark the packets in prerouting before the natting....
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 4 lines · Rajesh
Hi
I wish to implement Bandwith sharing in a NAT environment.
Quoted 9 lines
The question is whether I can classify input packets on the basis of ip-addresses (private LAN addresses)? These packets finally need to be NATed before going on to Internet.
Would the tc filters see the private addresses and put it in the appropriate classes or would the tc filters see only the NATed address and the filter would fail in putting the packets in the appropriate classes?
The n/w diag would be somewhat like this
private address LAN ips ------>iptables(NAT)------>Internet.
private address LAN ips ------>tc(netlink)--------->iptables(NAT)------>Internet
I feel this is how it is...so dnat will be after tc in LAN to WAN and snat will be before tc in WAN to LAN.
-Raghu
Quoted 11 lines
Can I mark packets using iptables matching source ip-address? What address will tc filter see when the private addresses are masqueraded ?
Any help is most welcome.
Cheers,
Rajesh
Quoted 10 lines
_______________________________________________
No banners. No pop-ups. No kidding.
Introducing My Way - http://www.myway.com
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
In a NAT environment, it is advisable to mark packets in prerouting stage. Subsequently, till the packets leaves the system , the mark will not be changed by any other process except a explicit mark iptables statement. Even if NAT changes IP address, the fw mark will still be the same allowing for classification. AFAIK, mark can have values rangign from 1 to 255.
Mohan
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Raghuveer
Sent: Thursday, August 14, 2003 4:33 PM
To: [email protected]
Cc: [email protected]
Subject: Re: [LARTC] Bandwith sharing in NAT environment.
Quoted 5 lines · Rajesh
Hi
I wish to implement Bandwith sharing in a NAT environment.
The question is whether I can classify input packets on the basis of
ip-addresses (private LAN addresses)? These packets finally need to be NATed before going on to Internet.
Quoted 2 lines
Would the tc filters see the private addresses and put it in the
appropriate classes or would the tc filters see only the NATed address and the filter would fail in putting the packets in the appropriate classes?
Quoted 6 lines
The n/w diag would be somewhat like this
private address LAN ips ------>iptables(NAT)------>Internet.
private address LAN
ips ------>tc(netlink)--------->iptables(NAT)------>Internet
I feel this is how it is...so dnat will be after tc in LAN to WAN and snat will be before tc in WAN to LAN.
-Raghu
Quoted 2 lines
Can I mark packets using iptables matching source ip-address? What address will tc filter see when the private addresses are masqueraded
?
Quoted 9 lines
Any help is most welcome.
Cheers,
Rajesh
Quoted 10 lines
_______________________________________________
No banners. No pop-ups. No kidding.
Introducing My Way - http://www.myway.com
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/