Skip to contentSkip to conversation

QOS problems switching from CBQ to HTB.

LARTC Curtis V. Schleich 3 participants 7 messages Sep 15, 2003 – Sep 16, 2003

lore
Share & tools
lore
#0 lore raw

Hello all! So as not to inundate the entire list with a huge email, I have put together a web page that
explains my situation and problem in detail. Here is a quick summary:

                                  Internet
                                     |
                                     |
                                     |
                           CCAonline Router (Cisco)
                                     |
                                     |
                                     |
                                   (eth0)
                            Master CCAonline AP
                           HTB Bandwidth control
                                  (wlan0)
                                     |
                                     |
                                     |
                            =========                           /  /  /  /|\  \  \  \
                          /  /  /  / | \  \  \  \
                         /  /  /  /  |  \  \  \  \
                    (Lots of Wireless Clients) |  \
                                               /   \
                                              /     \
                                            AP1     AP2
                                           /          \
                                          /            \
                                      ====        ===                                     /  /|\  \      /  /|\  \
                                    /  / | \  \    /  / | \  \
                                  Other Wireless  Other Wireless
                                      Clients         Clients

Up until a few weeks ago, we had been using kernel version 2.4.18 and CBQ.init to control bandwidth. I set that up quite a long time ago, and only vaguely understood bandwidth control when I did, but it seemed to work well enough. A few weeks ago, the hard drive began to fail in our master AP. I had been working on designing its replacement anyway, so I was able to make it limp along until I got 'Son of Master AP' up and running. The problem we have now is that QOS is pretty crappy. I've read the LARTC HOWTO, and pretty much the entire docum.org site. I feel like I have a relatively good handle on the subject matter, but I'm not able to achieve good QOS. I'm mainly looking for advice and input on how best to fairly share the available bandwidth among the subscribers to our service. Ultimately we will want a higher priority level for business clients, but that can wait until the basics are under control. All details are available from
http://wireless.ccaonline.com/lartcThanks, everyone! This is a great list!Curtis V. Schleich,CCA and CCAonline,cvslist (at) ccaonline (dot) com

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Curtis V. Schleich
Quoted 24 lines · Curtis V. Schleich

Hello all! So as not to inundate the entire list with a huge email, I have put together a web page that
explains my situation and problem in detail. Here is a quick summary:

                                  Internet



                           CCAonline Router (Cisco)



                                   (eth0)
                            Master CCAonline AP
                           HTB Bandwidth control
                                  (wlan0)



                            =========>                            /  /  /  /|\  \  \  \
                          /  /  /  / | \  \  \  \
                         /  /  /  /  |  \  \  \  \
                    (Lots of Wireless Clients) |  \
                                               /   \
Quoted 8 lines
                                              /     \
                                            AP1     AP2
                                           /          \
                                          /            \
                                      ====        ===>                                      /  /|\  \      /  /|\  \
                                    /  / | \  \    /  / | \  \
                                  Other Wireless  Other Wireless
                                      Clients         Clients

Can you try to add "quantum 1500" or maybe 4000 to each class?

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to Curtis V. Schleich

Trying 4000 right now, I'll try 1500 after I have a chance to see if 4000 makes any difference. I have put new commands and stats (which I will update periodically over the next few hours) at the
http://wireless.ccaonline.com/lartc/ site. On initial examination it does not seem to be making any significant difference. I've still got very laggy ping times, which I did not have when we were using CBQ. During the HTB research, I did discover that my CBQ setup was probably weird. I had a class for each user directly off the root, and the total rates FAR exceeded the available bandwidth. So from what I read it was probably pretty whacked, but I always seemed to have stable pings under 10ms. These are all over the map (or graph as the case may be).

Anything else??

Thanks!!

CVS
----- Original Message -----
From: "Stef Coene" <[email protected]>
To: "Curtis V. Schleich" <[email protected]>; <[email protected]>
Sent: Monday, September 15, 2003 3:18 PM
Subject: Re: [LARTC] QOS problems switching from CBQ to HTB.

Quoted 2 lines · Curtis V. Schleich
Quoted 1 line

Hello all! So as not to inundate the entire list with a huge email, I

have

Quoted 31 lines
Quoted 23 lines

put together a web page that
explains my situation and problem in detail. Here is a quick summary:

                                  Internet



                           CCAonline Router (Cisco)



                                   (eth0)
                            Master CCAonline AP
                           HTB Bandwidth control
                                  (wlan0)



                            =========> >                            /  /  /  /|\  \  \  \
                          /  /  /  / | \  \  \  \
                         /  /  /  /  |  \  \  \  \
                    (Lots of Wireless Clients) |  \
                                               /   \
Quoted 8 lines
                                              /     \
                                            AP1     AP2
                                           /          \
                                          /            \
                                      ====        ===> >                                      /  /|\  \      /  /|\  \
                                    /  / | \  \    /  / | \  \
                                  Other Wireless  Other Wireless
                                      Clients         Clients
Quoted 10 lines

Can you try to add "quantum 1500" or maybe 4000 to each class?

Stef

Signature · 4 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to Curtis V. Schleich
Quoted 6 lines · Curtis V. Schleich

Trying 4000 right now, I'll try 1500 after I have a chance to see if 4000 makes any difference. I have put new commands and stats (which I will update periodically over the next few hours) at the
http://wireless.ccaonline.com/lartc/ site. On initial examination it does not seem to be making any significant difference. I've still got very laggy ping times, which I did not have when we were using CBQ.

just a red herring for you, ;-), but you may need to use some arbitrated channel access mechanism for this many users off one AP, viz WiCCP, otherwise channel contention will become an issue. This will likely cause high ping times.

/steve

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#5 lore raw
In reply to Curtis V. Schleich

Agreed, but just a few weeks ago, using CBQ, things were calm and stable. I can check to see if our overall data transfer is up from a month ago. Thanks for the fish!

CVS

----- Original Message -----
From: "Steve Wright" <[email protected]>
To: "Curtis V. Schleich" <[email protected]>
Cc: "Stef Coene" <[email protected]>; <[email protected]>
Sent: Monday, September 15, 2003 4:49 PM
Subject: Re: [LARTC] QOS problems switching from CBQ to HTB.

Quoted 2 lines · Curtis V. Schleich
Quoted 1 line

Trying 4000 right now, I'll try 1500 after I have a chance to see if

4000

Quoted 3 lines
Quoted 3 lines

makes any difference. I have put new commands and stats (which I will update periodically over the next few hours) at the
http://wireless.ccaonline.com/lartc/ site. On initial examination it

does

Quoted 1 line
Quoted 1 line

not seem to be making any significant difference. I've still got very

laggy

Quoted 9 lines
Quoted 1 line

ping times, which I did not have when we were using CBQ.

just a red herring for you, ;-), but you may need to use some arbitrated channel access mechanism for this many users off one AP, viz WiCCP, otherwise channel contention will become an issue. This will likely cause high ping times.

Quoted 6 lines

/steve

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#6 lore raw
In reply to Curtis V. Schleich
Quoted 11 lines · Curtis V. Schleich

Trying 4000 right now, I'll try 1500 after I have a chance to see if 4000 makes any difference. I have put new commands and stats (which I will update periodically over the next few hours) at the
http://wireless.ccaonline.com/lartc/ site. On initial examination it does not seem to be making any significant difference. I've still got very laggy ping times, which I did not have when we were using CBQ. During the HTB research, I did discover that my CBQ setup was probably weird. I had a class for each user directly off the root, and the total rates FAR exceeded the available bandwidth. So from what I read it was probably pretty whacked, but I always seemed to have stable pings under 10ms. These are all over the map (or graph as the case may be).

Can put your cbq setup on your web-server? So we can compare....

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/