Skip to contentSkip to conversation

HTB and metro+int. limits

LARTC Alex 2 participants 3 messages Sep 30, 2003 – Oct 1, 2003

lore
Share & tools
lore

Alex

author
#0 lore raw

Thanks for your replay, it really helps, but to take the question further, from what you have seen in my sample script, how should I classify packets with "tc" ? I don't know how to put them in separate classes,. What I have in my script will only shape metro traffic, but for international how would the "tc" command be?
Something like:
/sbin/tc class add dev eth2 parent 1:2 classid 2:11 htb rate 50kbit ceil 100kbit prio 5
/sbin/tc filter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip dst 192.168.254.10 flowid 1:11
Would this be the correct commands?

Thanks again.

Alex
---begin my script----
sbin/tc qdisc add dev eth2 root handle 1: htb default 10 /sbin/tc class add dev eth2 parent 1: classid 1:1 htb rate 10M #metro
/sbin/tc class add dev eth2 parent 1:1 classid 1:10 htb rate 10M /sbin/tc filter add dev eth2 protocol ip parent 1:10 prio 3 handle 6 flowid 1:10
#international
/sbin/tc class add dev eth2 parent 1:1 classid 1:2 htb rate 10M /sbin/tc filter add dev eth2 protocol ip parent 1:10 prio 3 handle 5 flowid 1:2

/sbin/tc class add dev eth2 parent 1:1 classid 1:11 htb rate 50kbit ceil 100kbit prio 5
/sbin/tc filter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip dst 192.168.254.10 flowid 1:11

/sbin/tc class add dev eth2 parent 1:1 classid 1:12 htb rate 50kbit ceil 100kbit prio 5
/sbin/tc filter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip dst 192.168.254.11 flowid 1:12
....etc
--end--
----- Original Message -----
From: <[email protected]>
To: "Alex" <[email protected]>
Sent: Tuesday, September 30, 2003 9:07 PM
Subject: Re: HTB and metro+int. limits

Quoted 6 lines

Alex

Quoted 2 lines · Alex

Hello,
I need to setup HTB to limit the bandwidth, but I need to have 2 types

of

Quoted 2 lines
Quoted 2 lines

limits, because my ISP gives me more bandwith for sites located in my country, than others located outside. I have setup the following script

in

Quoted 8 lines
Quoted 8 lines

which I mark packets with mark 6 for the ip clasess for the sites in my country. What I don't know is how to continue the script with assigning lower limits to everything else not going from ip's in --set-mark 6. Maybe some of can enlighten me about this.
Thanks,

Alex

Quoted 8 lines

<snip>
......

Quoted 6 lines

/sbin/iptables -t mangle -A PREROUTING -i eth2 -d 193.231.15.0/24 -j MARK --set-mark 6
#end metro
#
#2. Anything else
/sbin/iptables -t mangle -A PREROUTING -i eth2 -d 0/0 -j MARK --set-mark

5

Quoted 4 lines

</snip>

This will not differentiate your traffic. Everything "-i eth2" will end

up

Quoted 2 lines

marked '5' because iptables will evaluate against every rule in order, eventually marking them '5' whether they have previously been marked '6'

or

Quoted 10 lines

not.

You need to create a new table with two commands for each address range. ie:

/sbin/iptables -t mangle -N MYMARKER /sbin/iptables -t mangle -A PREROUTING -i eth2 -j MYMARKER

# and ...
/sbin/iptables -t mangle -A MYMARKER -d 193.231.15.0/24 -j MARK --set-mark

6

Quoted 6 lines

/sbin/iptables -t mangle -A MYMARKER -d 193.231.15.0/24 -j RETURN

# for each metro range, and finally ....
/sbin/iptables -t mangle -A MYMARKER -j MARK --set-mark 5
/sbin/iptables -t mangle -A MYMARKER -j RETURN

The separate table and the 'RETURN' statements give you the

"short-circuit"

Quoted 8 lines

evaluation you require.

BTW: You might be able to consolidate your metro class-C's into fewer (larger) CIDR ranges to speed evaluation. ( Your upstream provider has likely been allocated them in this manner )

mulc

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 11 lines · Alex

Thanks for your replay, it really helps, but to take the question further, from what you have seen in my sample script, how should I classify packets with "tc" ? I don't know how to put them in separate classes,. What I have in my script will only shape metro traffic, but for international how would the "tc" command be?
Something like:
/sbin/tc class add dev eth2 parent 1:2 classid 2:11 htb rate 50kbit ceil 100kbit prio 5
/sbin/tc filter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip dst 192.168.254.10 flowid 1:11
Would this be the correct commands?

No. You create a class with a wrong number. If the parent class is 1:x, the class name has to be 1:y.

Quoted 10 lines

Thanks again.

Alex
---begin my script----
sbin/tc qdisc add dev eth2 root handle 1: htb default 10 /sbin/tc class add dev eth2 parent 1: classid 1:1 htb rate 10M #metro
/sbin/tc class add dev eth2 parent 1:1 classid 1:10 htb rate 10M /sbin/tc filter add dev eth2 protocol ip parent 1:10 prio 3 handle 6 flowid 1:10

This filter will not do much (typo?). You attach it to class 1:10 (the parent parameter). This should be 1: so all packets leaving eth2 will be checked against this filter.
And is 10M working? Normally 10mbit is used.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
author
#2 lore raw
In reply to Alex

I'm sorry, but I'm still confused about assigning separate limits for metro and international traffic.
After I mark metro traffic with --set-mark 6 and int. traffic with --set-mark 5 what's the next step?
Can someone give me an example? It seems that my approach is somehow wrong after marking of the packets.

Thanks again.

Alex
----- Original Message -----
From: "Stef Coene" <[email protected]>
To: "Alex" <[email protected]>; "Lartc" <[email protected]>; <[email protected]>
Sent: Wednesday, October 01, 2003 12:59 PM
Subject: Re: [LARTC] Re: HTB and metro+int. limits

Quoted 2 lines · Alex
Quoted 1 line

Thanks for your replay, it really helps, but to take the question

further,

Quoted 1 line
Quoted 1 line

from what you have seen in my sample script, how should I classify

packets

Quoted 1 line
Quoted 1 line

with "tc" ? I don't know how to put them in separate classes,. What I

have

Quoted 1 line
Quoted 1 line

in my script will only shape metro traffic, but for international how

would

Quoted 5 lines
Quoted 5 lines

the "tc" command be?
Something like:
/sbin/tc class add dev eth2 parent 1:2 classid 2:11 htb rate 50kbit ceil 100kbit prio 5
/sbin/tc filter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip

dst

Quoted 3 lines
Quoted 2 lines

192.168.254.10 flowid 1:11
Would this be the correct commands?

No. You create a class with a wrong number. If the parent class is 1:x,

the

Quoted 11 lines

class name has to be 1:y.

Quoted 9 lines

Thanks again.

Alex
---begin my script----
sbin/tc qdisc add dev eth2 root handle 1: htb default 10 /sbin/tc class add dev eth2 parent 1: classid 1:1 htb rate 10M #metro
/sbin/tc class add dev eth2 parent 1:1 classid 1:10 htb rate 10M /sbin/tc filter add dev eth2 protocol ip parent 1:10 prio 3 handle 6

flowid

Quoted 2 lines
Quoted 1 line

1:10

This filter will not do much (typo?). You attach it to class 1:10 (the

parent

Quoted 4 lines

parameter). This should be 1: so all packets leaving eth2 will be checked against this filter.
And is 10M working? Normally 10mbit is used.

Quoted 11 lines

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/