HTB and metro+int. limits
Thanks for your replay, it really helps, but to take the question further, from what you have seen in my sample script, how should I classify packets with "tc" ? I don't know how to put them in separate classes,. What I have in my script will only shape metro traffic, but for international how would the "tc" command be?
Something like:/sbin/tc class add dev eth2 parent 1:2 classid 2:11 htb rate 50kbit ceil 100kbit prio 5/sbin/tc filter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip dst 192.168.254.10 flowid 1:11
Would this be the correct commands?
Thanks again.
Alex
---begin my script----
sbin/tc qdisc add dev eth2 root handle 1: htb default 10 /sbin/tc class add dev eth2 parent 1: classid 1:1 htb rate 10M #metro/sbin/tc class add dev eth2 parent 1:1 classid 1:10 htb rate 10M /sbin/tc filter add dev eth2 protocol ip parent 1:10 prio 3 handle 6 flowid 1:10
#international/sbin/tc class add dev eth2 parent 1:1 classid 1:2 htb rate 10M /sbin/tc filter add dev eth2 protocol ip parent 1:10 prio 3 handle 5 flowid 1:2
/sbin/tc class add dev eth2 parent 1:1 classid 1:11 htb rate 50kbit ceil 100kbit prio 5/sbin/tc filter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip dst 192.168.254.10 flowid 1:11
/sbin/tc class add dev eth2 parent 1:1 classid 1:12 htb rate 50kbit ceil 100kbit prio 5/sbin/tc filter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip dst 192.168.254.11 flowid 1:12
....etc
--end--
----- Original Message -----
From: <[email protected]>
To: "Alex" <[email protected]>
Sent: Tuesday, September 30, 2003 9:07 PM
Subject: Re: HTB and metro+int. limits
Quoted 6 lines
Alex
Quoted 2 lines · Alex
Hello,
I need to setup HTB to limit the bandwidth, but I need to have 2 types
of
Quoted 2 lines
Quoted 2 lines
limits, because my ISP gives me more bandwith for sites located in my country, than others located outside. I have setup the following script
in
Quoted 8 lines
Quoted 8 lines
which I mark packets with mark 6 for the ip clasess for the sites in my country. What I don't know is how to continue the script with assigning lower limits to everything else not going from ip's in --set-mark 6. Maybe some of can enlighten me about this.
Thanks,Alex
Quoted 8 lines
<snip>
......Quoted 6 lines
/sbin/iptables-t mangle -A PREROUTING -i eth2 -d 193.231.15.0/24 -j MARK --set-mark 6
#end metro
#
#2. Anything else/sbin/iptables-t mangle -A PREROUTING -i eth2 -d 0/0 -j MARK --set-mark
5
Quoted 4 lines
</snip>
This will not differentiate your traffic. Everything "-i eth2" will end
up
Quoted 2 lines
marked '5' because iptables will evaluate against every rule in order, eventually marking them '5' whether they have previously been marked '6'
or
Quoted 10 lines
not.
You need to create a new table with two commands for each address range. ie:
/sbin/iptables-t mangle -N MYMARKER/sbin/iptables-t mangle -A PREROUTING -i eth2 -j MYMARKER# and ... /sbin/iptables -t mangle -A MYMARKER -d 193.231.15.0/24 -j MARK --set-mark
6
Quoted 6 lines
/sbin/iptables-t mangle -A MYMARKER -d 193.231.15.0/24 -j RETURN# for each metro range, and finally .... /sbin/iptables -t mangle -A MYMARKER -j MARK --set-mark 5 /sbin/iptables -t mangle -A MYMARKER -j RETURNThe separate table and the 'RETURN' statements give you the
"short-circuit"
Quoted 8 lines
evaluation you require.
BTW: You might be able to consolidate your metro class-C's into fewer (larger) CIDR ranges to speed evaluation. ( Your upstream provider has likely been allocated them in this manner )
mulc
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 11 lines · Alex
Thanks for your replay, it really helps, but to take the question further, from what you have seen in my sample script, how should I classify packets with "tc" ? I don't know how to put them in separate classes,. What I have in my script will only shape metro traffic, but for international how would the "tc" command be?
Something like:/sbin/tcclass add dev eth2 parent 1:2 classid 2:11 htb rate 50kbit ceil 100kbit prio 5/sbin/tcfilter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip dst 192.168.254.10 flowid 1:11
Would this be the correct commands?
No. You create a class with a wrong number. If the parent class is 1:x, the class name has to be 1:y.
Quoted 10 lines
Thanks again.
Alex
---begin my script----
sbin/tc qdisc add dev eth2 root handle 1: htb default 10/sbin/tcclass add dev eth2 parent 1: classid 1:1 htb rate 10M #metro/sbin/tcclass add dev eth2 parent 1:1 classid 1:10 htb rate 10M/sbin/tcfilter add dev eth2 protocol ip parent 1:10 prio 3 handle 6 flowid 1:10
This filter will not do much (typo?). You attach it to class 1:10 (the parent parameter). This should be 1: so all packets leaving eth2 will be checked against this filter.
And is 10M working? Normally 10mbit is used.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
I'm sorry, but I'm still confused about assigning separate limits for metro and international traffic.
After I mark metro traffic with --set-mark 6 and int. traffic with --set-mark 5 what's the next step?
Can someone give me an example? It seems that my approach is somehow wrong after marking of the packets.
Thanks again.
Alex
----- Original Message -----
From: "Stef Coene" <[email protected]>
To: "Alex" <[email protected]>; "Lartc" <[email protected]>; <[email protected]>
Sent: Wednesday, October 01, 2003 12:59 PM
Subject: Re: [LARTC] Re: HTB and metro+int. limits
Quoted 2 lines · Alex
Quoted 1 line
Thanks for your replay, it really helps, but to take the question
further,
Quoted 1 line
Quoted 1 line
from what you have seen in my sample script, how should I classify
packets
Quoted 1 line
Quoted 1 line
with "tc" ? I don't know how to put them in separate classes,. What I
have
Quoted 1 line
Quoted 1 line
in my script will only shape metro traffic, but for international how
would
Quoted 5 lines
Quoted 5 lines
the "tc" command be?
Something like:/sbin/tcclass add dev eth2 parent 1:2 classid 2:11 htb rate 50kbit ceil 100kbit prio 5/sbin/tcfilter add dev eth2 parent 1:0 protocol ip prio 5 u32 match ip
dst
Quoted 3 lines
Quoted 2 lines
192.168.254.10 flowid 1:11
Would this be the correct commands?No. You create a class with a wrong number. If the parent class is 1:x,
the
Quoted 11 lines
class name has to be 1:y.
Quoted 9 lines
Thanks again.
Alex
---begin my script----
sbin/tc qdisc add dev eth2 root handle 1: htb default 10/sbin/tcclass add dev eth2 parent 1: classid 1:1 htb rate 10M #metro/sbin/tcclass add dev eth2 parent 1:1 classid 1:10 htb rate 10M/sbin/tcfilter add dev eth2 protocol ip parent 1:10 prio 3 handle 6
flowid
Quoted 2 lines
Quoted 1 line
1:10
This filter will not do much (typo?). You attach it to class 1:10 (the
parent
Quoted 4 lines
parameter). This should be 1: so all packets leaving eth2 will be checked against this filter.
And is 10M working? Normally 10mbit is used.
Quoted 11 lines
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/