Skip to contentSkip to conversation

htb v3 not as good as htb v2?

LARTC Anton Yurchenko 5 participants 6 messages Oct 8, 2003 – Oct 9, 2003

lore
Share & tools
lore
#0 lore raw

Hello,

I`ve been using htb v2 for more then a year without any major problems. Recently I needed to upgrade to newer kernel becouse of non LARTC related issues. After installing 2.4.22 when the htb qdisc was attached to the interface even without any rules, I was not able to send more ~1mbit through the interface. After I reversed the htb3 patch and rebuild with htb2 everything works as normal. Has anyone experienced the same issue? thanks

Signature · 7 lines
Anton Yurchenko<[email protected]>
Digital Generation


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw

Hello Anton,

Wednesday, October 8, 2003, 4:49:30 PM, you wrote:

I am using HTB3 with more than 10 megabits customers, and amount of classes about 100-200 without any problem.
Only one what i do - i make filter with lowest priority, to not pass ass unclassified traffic to default class, just to drop it. I think you just need review your classes, because also if you have any rate more 468 Kbit, you need change r2q or quantum.

AY> Hello,

AY> I`ve been using htb v2 for more then a year without any major problems. AY> Recently I needed to upgrade to newer kernel becouse of non LARTC AY> related issues. After installing 2.4.22 when the htb qdisc was attached AY> to the interface even without any rules, I was not able to send more AY> ~1mbit through the interface. After I reversed the htb3 patch and AY> rebuild with htb2 everything works as normal. Has anyone experienced the AY> same issue? thanks

Signature · 6 lines
Best regards,
 Denis                            mailto:[email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Anton Yurchenko

I've used HTB and CBQ to protect MPEG2 traffic streams from UDP traffic over 100 Mb/s interfaces. I have not yet attempted this with 1000 Mb/s interfaces, but I hope to get to that this year (it it much more difficult to measure accurately at this speed).

Quoted 9 lines · Anton Yurchenko

Hello,

I`ve been using htb v2 for more then a year without any major problems. Recently I needed to upgrade to newer kernel becouse of non LARTC related issues. After installing 2.4.22 when the htb qdisc was attached to the interface even without any rules, I was not able to send more ~1mbit through the interface. After I reversed the htb3 patch and rebuild with htb2 everything works as normal. Has anyone experienced the same issue? thanks

Signature · 3 lines
    Lawrence MacIntyre     865.574.8696     [email protected]
               Oak Ridge National Laboratory
High Performance Information Infrastructure Technology Group
#3 lore raw
In reply to Anton Yurchenko
Quoted 10 lines · Anton Yurchenko

Hello,

I`ve been using htb v2 for more then a year without any major problems. Recently I needed to upgrade to newer kernel becouse of non LARTC related issues. After installing 2.4.22 when the htb qdisc was attached to the interface even without any rules, I was not able to send more ~1mbit through the interface. After I reversed the htb3 patch and rebuild with htb2 everything works as normal. Has anyone experienced the same issue? thanks

check your burst and quantum settings. maybe they are too low.

bye,
wilfried

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to Anton Yurchenko
Quoted 12 lines · [email protected] wrote:

Hello Anton,

Wednesday, October 8, 2003, 4:49:30 PM, you wrote:

I am using HTB3 with more than 10 megabits customers, and amount of classes about 100-200 without any problem.
Only one what i do - i make filter with lowest priority, to not pass ass unclassified traffic to default class, just to drop it. I think you just need review your classes, because also if you have any rate more 468 Kbit, you need change r2q or quantum.

the problem was observed even when only adding a qdisc, no classes. how can this be?

Quoted 15 lines

AY> Hello,

AY> I`ve been using htb v2 for more then a year without any major problems. AY> Recently I needed to upgrade to newer kernel becouse of non LARTC AY> related issues. After installing 2.4.22 when the htb qdisc was attached AY> to the interface even without any rules, I was not able to send more AY> ~1mbit through the interface. After I reversed the htb3 patch and AY> rebuild with htb2 everything works as normal. Has anyone experienced the AY> same issue? thanks

Signature · 7 lines
Anton Yurchenko<[email protected]>
Digital Generation


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#5 lore raw
In reply to Anton Yurchenko
Quoted 12 lines · Anton Yurchenko
Quoted 10 lines · [email protected] wrote:

Hello Anton,

Wednesday, October 8, 2003, 4:49:30 PM, you wrote:

I am using HTB3 with more than 10 megabits customers, and amount of classes about 100-200 without any problem.
Only one what i do - i make filter with lowest priority, to not pass ass unclassified traffic to default class, just to drop it. I think you just need review your classes, because also if you have any rate more 468 Kbit, you need change r2q or quantum.

Quoted 2 lines

the problem was observed even when only adding a qdisc, no classes. how can this be?

What's the output of
tc -s -d qdisc show dev eth0
tc -s -d class show dev eth0

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/