htb v3 not as good as htb v2?
Hello,
I`ve been using htb v2 for more then a year without any major problems. Recently I needed to upgrade to newer kernel becouse of non LARTC related issues. After installing 2.4.22 when the htb qdisc was attached to the interface even without any rules, I was not able to send more ~1mbit through the interface. After I reversed the htb3 patch and rebuild with htb2 everything works as normal. Has anyone experienced the same issue? thanks
Signature · 7 lines
Anton Yurchenko<[email protected]> Digital Generation _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hello Anton,
Wednesday, October 8, 2003, 4:49:30 PM, you wrote:
I am using HTB3 with more than 10 megabits customers, and amount of classes about 100-200 without any problem.
Only one what i do - i make filter with lowest priority, to not pass ass unclassified traffic to default class, just to drop it. I think you just need review your classes, because also if you have any rate more 468 Kbit, you need change r2q or quantum.
AY> Hello,
AY> I`ve been using htb v2 for more then a year without any major problems. AY> Recently I needed to upgrade to newer kernel becouse of non LARTC AY> related issues. After installing 2.4.22 when the htb qdisc was attached AY> to the interface even without any rules, I was not able to send more AY> ~1mbit through the interface. After I reversed the htb3 patch and AY> rebuild with htb2 everything works as normal. Has anyone experienced the AY> same issue? thanks
Signature · 6 lines
Best regards, Denis mailto:[email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
I've used HTB and CBQ to protect MPEG2 traffic streams from UDP traffic over 100 Mb/s interfaces. I have not yet attempted this with 1000 Mb/s interfaces, but I hope to get to that this year (it it much more difficult to measure accurately at this speed).
Quoted 9 lines · Anton Yurchenko
Hello,
I`ve been using htb v2 for more then a year without any major problems. Recently I needed to upgrade to newer kernel becouse of non LARTC related issues. After installing 2.4.22 when the htb qdisc was attached to the interface even without any rules, I was not able to send more ~1mbit through the interface. After I reversed the htb3 patch and rebuild with htb2 everything works as normal. Has anyone experienced the same issue? thanks
Signature · 3 lines
Lawrence MacIntyre 865.574.8696 [email protected] Oak Ridge National Laboratory High Performance Information Infrastructure Technology Group
Quoted 10 lines · Anton Yurchenko
Hello,
I`ve been using htb v2 for more then a year without any major problems. Recently I needed to upgrade to newer kernel becouse of non LARTC related issues. After installing 2.4.22 when the htb qdisc was attached to the interface even without any rules, I was not able to send more ~1mbit through the interface. After I reversed the htb3 patch and rebuild with htb2 everything works as normal. Has anyone experienced the same issue? thanks
check your burst and quantum settings. maybe they are too low.
bye,
wilfried
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 12 lines · [email protected] wrote:
Hello Anton,
Wednesday, October 8, 2003, 4:49:30 PM, you wrote:
I am using HTB3 with more than 10 megabits customers, and amount of classes about 100-200 without any problem.
Only one what i do - i make filter with lowest priority, to not pass ass unclassified traffic to default class, just to drop it. I think you just need review your classes, because also if you have any rate more 468 Kbit, you need change r2q or quantum.
the problem was observed even when only adding a qdisc, no classes. how can this be?
Quoted 15 lines
AY> Hello,
AY> I`ve been using htb v2 for more then a year without any major problems. AY> Recently I needed to upgrade to newer kernel becouse of non LARTC AY> related issues. After installing 2.4.22 when the htb qdisc was attached AY> to the interface even without any rules, I was not able to send more AY> ~1mbit through the interface. After I reversed the htb3 patch and AY> rebuild with htb2 everything works as normal. Has anyone experienced the AY> same issue? thanks
Signature · 7 lines
Anton Yurchenko<[email protected]> Digital Generation _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 12 lines · Anton Yurchenko
Quoted 10 lines · [email protected] wrote:
Hello Anton,
Wednesday, October 8, 2003, 4:49:30 PM, you wrote:
I am using HTB3 with more than 10 megabits customers, and amount of classes about 100-200 without any problem.
Only one what i do - i make filter with lowest priority, to not pass ass unclassified traffic to default class, just to drop it. I think you just need review your classes, because also if you have any rate more 468 Kbit, you need change r2q or quantum.
Quoted 2 lines
the problem was observed even when only adding a qdisc, no classes. how can this be?
What's the output of
tc -s -d qdisc show dev eth0
tc -s -d class show dev eth0
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/