Skip to contentSkip to conversation

Wondershaper modifications

LARTC Thomas Kirk 2 participants 2 messages Oct 9, 2003

lore
Share & tools
lore
#0 lore raw

Hep Dear Listmembers and Stef!

Setup

      Internet
        eth0
          |
          |

-----------------
| | | |
eth1 eth2 eth3 eth4 <--- Lan .10/24 .11/24 etc

All Lans are natted to eth0

Now i use wondershaper (1.1a) on eth0 to shap interactive traffic (work allready thanks!) But i have a special requirments for priorities
samba traffic from eth1 to internet. Ive done this with the following lines in iptables and wondershaper :

iptables :

$IPTABLES -A PREROUTING -t mangle -p tcp --dport 137:139 -i eth1 -j MARK --set-mark 2
$IPTABLES -A PREROUTING -t mangle -p udp --dport 137:139 -i eth1 -j MARK --set-mark 2

wondershaper :

tc filter add dev $DEV parent 1:0 protocol ip prio 1 handle 2 fw classid 1:10

This setup seems to work partly. When i browser network on anohter host over internet i get no lag and fast response (low latency). But when i try to edit file (3kb) it takes around 10 seconds to save the file? Since my connection is 2048/512 and ive set my UPLINKE0 it should take no more than 1-2 secs to update a file over internet? What am i overlooking here?

Signature · 13 lines
Venlig hilsen/Kind regards
Thomas Kirk
ARKENA
tlf/phone +4570233456
thomas(at)arkena(dot)com
Http://www.arkena.com


"It's naive to think you can change a person--except maybe that
boy who works in the library." -- Lisa Simpson
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw
Quoted 33 lines · Thomas Kirk

Hep Dear Listmembers and Stef!

Setup

Internet
eth0

-----------------

eth1 eth2 eth3 eth4 <--- Lan .10/24 .11/24 etc

All Lans are natted to eth0

Now i use wondershaper (1.1a) on eth0 to shap interactive traffic (work allready thanks!) But i have a special requirments for priorities
samba traffic from eth1 to internet. Ive done this with the following lines in iptables and wondershaper :

iptables :

$IPTABLES -A PREROUTING -t mangle -p tcp --dport 137:139 -i eth1 -j MARK --set-mark 2
$IPTABLES -A PREROUTING -t mangle -p udp --dport 137:139 -i eth1 -j MARK --set-mark 2

wondershaper :

tc filter add dev $DEV parent 1:0 protocol ip prio 1 handle 2 fw classid 1:10

Quoted 6 lines

This setup seems to work partly. When i browser network on anohter host over internet i get no lag and fast response (low latency). But when i try to edit file (3kb) it takes around 10 seconds to save the file? Since my connection is 2048/512 and ive set my UPLINKE0 it should take no more than 1-2 secs to update a file over internet? What am i overlooking here?

Can you check the timeout with a simple ping? And what about making a directory or copying a file ?

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/