Skip to contentSkip to conversation

partly correct routing

LARTC Stefan Bayer [email protected] 2 participants 2 messages Dec 4, 2000

lore
Share & tools
lore

Stefan Bayer [email protected]

author
#0 lore raw

<PRE>Hello!
I want to use my isdn (ippp0) connection for ftp transfer and my adsl (eth0/ppp0) connection for all other transfer from my LAN (eth1) connected to the router.
I managed to set up iproute2 with fwmarks to send out packet to ippp0, but the data connection is done by adsl.
What do I have to set up to get this working correctly?
my iptables setup:
$IPTABLES -A PREROUTING -t mangle -p TCP -d ! $LOCALNET --dport 21 -j MARK --set-mark 1
$IPTABLES -A PREROUTING -t mangle -p UDP -d ! $LOCALNET --dport 21 -j MARK --set-mark 1
$IPTABLES -A PREROUTING -t mangle -p TCP -d ! $LOCALNET --dport 20 -j MARK --set-mark 1
$IPTABLES -A PREROUTING -t mangle -p UDP -d ! $LOCALNET --dport 20 -j MARK --set-mark 1

routing in table ippp0:
ip route list table ippp0
195.3.65.72 dev ippp0 proto kernel scope link src 212.183.78.79 default via 195.3.65.72 dev ippp0

other routing:
ip route list
212.88.181.5 dev ppp0 proto kernel scope link src 212.88.xxx.xxx 195.3.65.0/24 dev ippp0 proto kernel scope link src 212.183.78.79 10.0.0.0/24 dev eth0 proto kernel scope link src 10.0.0.2 192.168.2.0/24 dev eth1 proto kernel scope link src 192.168.2.1 127.0.0.0/8 dev lo scope link
default via 212.88.181.5 dev ppp0

ip rule list

0:      from all lookup local 
32765:  from all fwmark        1 lookup ippp0 
32766:  from all lookup main 
32767:  from all lookup default
Signature · 12 lines
thanx
Stefan
Email: <A HREF="mailto:[email protected]">[email protected]</A>
----------------------------------------------------
My Box said: &quot;Install Win95 or better ...&quot; So I installed Linux.

Microsoft gives you Windows
Linux gives you the whole house
	


</PRE>
#1 lore raw

<PRE>I think you misunderstand the FTP protocol. The FTP commands are sent to the server's port 21 and the data is sent FROM the server port 20 to a local unprivileged port (&gt;1024).

I think you should set your mark dependant on source port instead of destination port.

Another way: use passive FTP, where the client initiates the connection to a unprivileged server port.

(I know I don't give all the answers here, but hope it's a good start for you.

On Mon, 4 Dec 2000, Stefan Bayer wrote:

&gt;<i> Hello!
</I>&gt;<i> I want to use my isdn (ippp0) connection for ftp transfer and my adsl </I>&gt;<i> (eth0/ppp0) connection for all other transfer from my LAN (eth1) connected to </I>&gt;<i> the router.
</I>&gt;<i> I managed to set up iproute2 with fwmarks to send out packet to ippp0, but </I>&gt;<i> the data connection is done by adsl.
</I>&gt;<i> What do I have to set up to get this working correctly? </I>&gt;<i> my iptables setup:
</I>&gt;<i> $IPTABLES -A PREROUTING -t mangle -p TCP -d ! $LOCALNET --dport 21 -j MARK </I>&gt;<i> --set-mark 1
</I>&gt;<i> $IPTABLES -A PREROUTING -t mangle -p UDP -d ! $LOCALNET --dport 21 -j MARK </I>&gt;<i> --set-mark 1
</I>&gt;<i> $IPTABLES -A PREROUTING -t mangle -p TCP -d ! $LOCALNET --dport 20 -j MARK </I>&gt;<i> --set-mark 1
</I>&gt;<i> $IPTABLES -A PREROUTING -t mangle -p UDP -d ! $LOCALNET --dport 20 -j MARK </I>&gt;<i> --set-mark 1
</I>&gt;<i>
</I>&gt;<i> routing in table ippp0:
</I>&gt;<i> ip route list table ippp0
</I>&gt;<i> 195.3.65.72 dev ippp0 proto kernel scope link src 212.183.78.79 </I>&gt;<i> default via 195.3.65.72 dev ippp0
</I>&gt;<i>
</I>&gt;<i> other routing:
</I>&gt;<i> ip route list
</I>&gt;<i> 212.88.181.5 dev ppp0 proto kernel scope link src 212.88.xxx.xxx </I>&gt;<i> 195.3.65.0/24 dev ippp0 proto kernel scope link src 212.183.78.79 </I>&gt;<i> 10.0.0.0/24 dev eth0 proto kernel scope link src 10.0.0.2 </I>&gt;<i> 192.168.2.0/24 dev eth1 proto kernel scope link src 192.168.2.1 </I>&gt;<i> 127.0.0.0/8 dev lo scope link
</I>&gt;<i> default via 212.88.181.5 dev ppp0
</I>&gt;<i>
</I>&gt;<i>
</I>&gt;<i> ip rule list

</I>&gt;<i> 0:      from all lookup local
</I>&gt;<i> 32765:  from all fwmark        1 lookup ippp0
</I>&gt;<i> 32766:  from all lookup main
</I>&gt;<i> 32767:  from all lookup default

</I>

</PRE>