Skip to contentSkip to conversation

Latest 2.6 IA64 Baseline (Mosberger) testing report (Boot hang)

DISCUSSION Yu, Luming 2 participants 10 messages Nov 12, 2003 – Dec 10, 2003

lore
Share & tools
lore

Yu, Luming

author
#0 lore raw

ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100

Software Configuration:
-----------------------

	1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/11 (Shanghai time)

	Successfully automerged by bk without out any manually work.

ACPI Features Tested: (prioritized).
--------------------
1. Boot hang

Kernel hang after message:
<<2.6.config.ZIP>>
"ELILO boot : Loading vmlinux... Done"

Thanks,
Luming

#1 lore raw

It boots fine on Lion here, it looks like you might be using the wrong config? The config you attached is for ZX1/McKinley.

Matt

Quoted 33 lines · Luming

ACPI Test Report for 2.6 ia64 kernel ============> Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100

Software Configuration:
-----------------------

	1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/11 (Shanghai time)

	Successfully automerged by bk without out any manually work.

ACPI Features Tested: (prioritized).
--------------------
1. Boot hang

Kernel hang after message:
<<2.6.config.ZIP>>
"ELILO boot : Loading vmlinux... Done"

Thanks,
Luming

author
#2 lore raw
In reply to Yu, Luming

I double-checked my config file. You are right. After correcting this mistake, I can successfully boot 2.6 on lion.

Thanks
Luming

-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Matt Chapman
Sent: 2003?11?13? 11:14
To: Yu, Luming
Cc: linux-acpi; [email protected]
Subject: Re: Latest 2.6 IA64 Baseline (Mosberger) testing report (Boot hang)

It boots fine on Lion here, it looks like you might be using the wrong config? The config you attached is for ZX1/McKinley.

Matt

Quoted 26 lines · Luming

ACPI Test Report for 2.6 ia64 kernel ============> Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100

Software Configuration:
-----------------------

	1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/11 (Shanghai time)

	Successfully automerged by bk without out any manually work.

ACPI Features Tested: (prioritized).
--------------------
1. Boot hang

Quoted 7 lines

Kernel hang after message:
<<2.6.config.ZIP>>
"ELILO boot : Loading vmlinux... Done"

Thanks,
Luming

-
To unsubscribe from this list: send the line "unsubscribe linux-ia64" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

author
#3 lore raw
In reply to Yu, Luming

ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100

Software Configuration:
-----------------------

	1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/19 (Shanghai time)
	2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 11/19 (Shanghai time)
	Successfully automerged by bk without out any manually work.

	3. patch from http://bugzilla.kernel.org/show_bug.cgi?id=1533 to solve  kernel unaligned access when pressing power button

ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. PS/2 keyboard only work for a few minutes, then hang
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok

CPU0 CPU1 CPU2 CPU3

 29:          0          0          0          0          LSAPIC  cmc_poll
 30:          0          0          0          0  IO-SAPIC-level  cpe_hndlr
 31:          0          0          0          0          LSAPIC  cmc_hndlr
 32:        724          4         32          0   IO-SAPIC-edge  i8042
 33:        493          0          9          0   IO-SAPIC-edge  ide1
 34:         34          0          4          0   IO-SAPIC-edge  ide0
 36:        777         31         46          0   IO-SAPIC-edge  i8042
 39:          2          0          0          0  IO-SAPIC-level  acpi
 44:         16          0          3          0   IO-SAPIC-edge  serial
 45:         14          0          3          0   IO-SAPIC-edge  serial
 54:       1656          9         78          2  IO-SAPIC-level  uhci_hcd
 55:       1032          5         55          1  IO-SAPIC-level  eth0
 61:       5520         13        279          1  IO-SAPIC-level  qla1280
232:          0          0          0          0          LSAPIC  mca_rdzv
238:          0          0          0          0          LSAPIC  perfmon
239:     354543     349871     349425     348988          LSAPIC  timer
240:          0          0          0          0          LSAPIC  mca_wkup
254:        154        126        218        183          LSAPIC  IPI
NMI:          0          0          0          0
ERR:          0

Problems:

1. PS/2 keyboard only work for a few minutes, then hang.

2.alloc 0x0-0xcf7 from PCI IO for PCI Bus 0000:00 failed. (known issue)

3.ACPI: No IRQ known for interrupt pin B of device 0000:00:03.3. (Known issue)

<<dmesg.26.ZIP>> <<2.6.config.ZIP>> <<lspci.26.ZIP>>
Thanks,
Luming

author
#4 lore raw

RE: Latest 2.6 IA64 Baseline (Mosberger) testing report

In reply to Yu, Luming

It boot with any hang, but Leagcy keyboard hang. --Luming

Quoted 80 lines

-----Original Message-----
From: Yu, Luming
Sent: 2003Äê11ÔÂ19ÈÕ 20:43
To: linux-acpi
Cc: [email protected]
Subject: Latest 2.6 IA64 Baseline (Mosberger) testing report (Boot hang)

ACPI Test Report for 2.6 ia64 kernel ============> Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100

Software Configuration:
-----------------------

	1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/19 (Shanghai time)
	2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 11/19 (Shanghai time)
	Successfully automerged by bk without out any manually work.

	3. patch from http://bugzilla.kernel.org/show_bug.cgi?id33 to solve  kernel unaligned access when pressing power button

ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. PS/2 keyboard only work for a few minutes, then hang
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok

CPU0 CPU1 CPU2 CPU3

 29:          0          0          0          0          LSAPIC  cmc_poll
 30:          0          0          0          0  IO-SAPIC-level  cpe_hndlr
 31:          0          0          0          0          LSAPIC  cmc_hndlr
 32:        724          4         32          0   IO-SAPIC-edge  i8042
 33:        493          0          9          0   IO-SAPIC-edge  ide1
 34:         34          0          4          0   IO-SAPIC-edge  ide0
 36:        777         31         46          0   IO-SAPIC-edge  i8042
 39:          2          0          0          0  IO-SAPIC-level  acpi
 44:         16          0          3          0   IO-SAPIC-edge  serial
 45:         14          0          3          0   IO-SAPIC-edge  serial
 54:       1656          9         78          2  IO-SAPIC-level  uhci_hcd
 55:       1032          5         55          1  IO-SAPIC-level  eth0
 61:       5520         13        279          1  IO-SAPIC-level  qla1280
232:          0          0          0          0          LSAPIC  mca_rdzv
238:          0          0          0          0          LSAPIC  perfmon
239:     354543     349871     349425     348988          LSAPIC  timer
240:          0          0          0          0          LSAPIC  mca_wkup
254:        154        126        218        183          LSAPIC  IPI
NMI:          0          0          0          0
ERR:          0

Problems:

1. PS/2 keyboard only work for a few minutes, then hang.

2.alloc 0x0-0xcf7 from PCI IO for PCI Bus 0000:00 failed. (known issue)

3.ACPI: No IRQ known for interrupt pin B of device 0000:00:03.3. (Known issue)

<< File: dmesg.26.TXT (Compressed) >> << File: 2.6.config.TXT (Compressed) >> << File: lspci.26.TXT (Compressed) >>
Thanks,
Luming

author
#5 lore raw

Latest 2.6 IA64 Baseline (Mosberger) testing report

In reply to Yu, Luming

ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100

Software Configuration:

	1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/26 (Shanghai time)

	2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 11/26 (Shanghai time)
		failed. 

3. patch from http://bugzilla.kernel.org/show_bug.cgi?id=1533 to solve kernel unaligned access when pressing power button

ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console Didn't test
3. PS/2 keyboard tested ok
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok

CPU0 CPU1 CPU2 CPU3

 29:          0          0          0          0          LSAPIC  cmc_poll
 30:          0          0          0          0  IO-SAPIC-level  cpe_hndlr
 31:          0          0          0          0          LSAPIC  cmc_hndlr
 32:       1379          4          0         10   IO-SAPIC-edge  i8042
 33:        583         19          0         11   IO-SAPIC-edge  ide1
 34:         22         10          0          6   IO-SAPIC-edge  ide0
 36:        565          1          0         53   IO-SAPIC-edge  i8042
 39:          5          0          0          0  IO-SAPIC-level  acpi
 45:         11          5          0          0   IO-SAPIC-edge  serial
 54:       2415          4          0          0  IO-SAPIC-level  uhci_hcd
 55:       2958         46          4          2  IO-SAPIC-level  eth0
 61:       9152        320          3         15  IO-SAPIC-level  qla1280
232:          0          0          0          0          LSAPIC  mca_rdzv
238:          0          0          0          0          LSAPIC  perfmon
239:    1899520    1894834    1889372    1883893          LSAPIC  timer
240:          0          0          0          0          LSAPIC  mca_wkup
254:         84        135        109        128          LSAPIC  IPI
NMI:          0          0          0          0 
ERR:          0

Problems:

1. Failed to bk pull http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 , Error message was

" Entire repository is locked by:
RESYNC directory.
ERROR-Unable to lock repository for update"

2.alloc 0x0-0xcf7 from PCI IO for PCI Bus 0000:00 failed. (known issue)

3.ACPI: No IRQ known for interrupt pin B of device 0000:00:03.3. (Known issue)
<<2.6.config.ZIP>> <<dmesg.26.ZIP>> <<lspci.26.ZIP>>
Thanks
Luming

author
#6 lore raw

Latest 2.6 IA64 Baseline (Mosberger) testing report (Lion)

In reply to Yu, Luming

ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100

Software Configuration:

	1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 12/3 (Shanghai time)
	2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 12/3 (Shanghai time)

3.patch from http://bugzilla.kernel.org/show_bug.cgi?id=1533 to solve kernel unaligned access when pressing power button Resolved 1 conflict by hand.(Take change from linux-ia64-2.5)

ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. PS/2 keyboard After about 5 minutes, keyboard doesn't respond.
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok

CPU0 CPU1 CPU2 CPU3

 29:          0          0          0          0          LSAPIC  cmc_poll
 30:          0          0          0          0  IO-SAPIC-level  cpe_hndlr
 31:          0          0          0          0          LSAPIC  cmc_hndlr
 32:       1407          2         10         21   IO-SAPIC-edge  i8042
 33:        638          0          0          2   IO-SAPIC-edge  ide1
 34:         12          0         12         14   IO-SAPIC-edge  ide0
 36:        465         32         21          0   IO-SAPIC-edge  i8042
 39:          4          0          0          0  IO-SAPIC-level  acpi
 44:          6          0          0          2   IO-SAPIC-edge  serial
 45:         15          0          0          2   IO-SAPIC-edge  serial
 54:       2082          4         30          0  IO-SAPIC-level  uhci_hcd
 55:       2184          0         28         52  IO-SAPIC-level  eth0
 61:       8850          1         15        279  IO-SAPIC-level  qla1280
232:          0          0          0          0          LSAPIC  mca_rdzv
238:          0          0          0          0          LSAPIC  perfmon
239:     727038     722365     716577     711104          LSAPIC  timer
240:          0          0          0          0          LSAPIC  mca_wkup
254:        141        165        273        267          LSAPIC  IPI
NMI:          0          0          0          0
ERR:          0

Problems:

1.After login about 5 minutes, keyboard doesn't respond.

2.PCI: no interrupt route for 00:00:03 pin B. (Known issue)

3. alloc 0x0-0xcf7 from PCI IO for PCI Bus 00:00 failed (Known issue)

4. ide-floppy: hda: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
ide-floppy: hda: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
<<lspci.26.ZIP>> <<dmesg.26.ZIP>> <<2.6.config.ZIP>>
Thanks,
Luming

author
#7 lore raw

Latest 2.6 IA64 Baseline (Mosberger) testing report (Tiger)

In reply to Yu, Luming

ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-Tiger
System Type: 4 way 900 Itanium2, tiger
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
MPT scsi host driver
Seagate ST318406LC boot drive
IDE floppy and CDROM
Serial console
USB mouse
Ethernet Pro 1000

Software Configuration:

	1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 12/3 (Shanghai time)
	2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 12/3 (Shanghai time)
	3. patch from http://bugzilla.kernel.org/show_bug.cgi?id=1634 to fix compile-time bug.

	Resolved 1 conflict by hand.(Take change from linux-ia64-2.5)

ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. ATI (run X window system) tested ok
4. PS/2 mouse tested ok
5. USB mouse tested ok
6. NIC (eg. Ping or ftp) tested ok
7. IDE (eg. r/w floppy or CDROM) tested ok
8. SCI (eg. Press power button) tested ok
9. Soft Power off tested ok

CPU0 CPU1 CPU2 CPU3

 29:          0          0          0          0          LSAPIC  cmc_poll
 30:          0          0          0          0  IO-SAPIC-level  cpe_hndlr
 31:          0          0          0          0          LSAPIC  cmc_hndlr
 34:          1          0         63          0   IO-SAPIC-edge  ide0
 39:          0          0          4          0  IO-SAPIC-level  acpi
 45:          0          1         94          0   IO-SAPIC-edge  serial
 48:          0          0          0          0  IO-SAPIC-level  ehci_hcd
 49:          1         24       1812          0  IO-SAPIC-level  uhci_hcd
 50:          0          0         40          0  IO-SAPIC-level  uhci_hcd
 51:          0          2        399          0  IO-SAPIC-level  eth0
 56:          7        128       3828          0  IO-SAPIC-level  ioc0
 57:          0          0         42          0  IO-SAPIC-level  ioc1
232:          0          0          0          0          LSAPIC  mca_rdzv
238:          0          0          0          0          LSAPIC  perfmon
239:     203826     198715     198222     197807          LSAPIC  timer
240:          0          0          0          0          LSAPIC  mca_wkup
254:         34         94         87         91          LSAPIC  IPI
NMI:          0          0          0          0
ERR:          0

Problems:

Please refer dmesg attached .

[Dmesg, /proc/interrupts, lspci -v , .config are attached below]
<<2.6.ZIP>>
Thanks,
Luming

author
#8 lore raw

Latest 2.6 IA64 Baseline (Mosberger) testing report (Lion)

In reply to Yu, Luming

ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100

Software Configuration:
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 12/10 (Shanghai time)
Nothing to pull
2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 12/10 (Shanghai time)
Nothing to pull

Since nothing to pull, test result is quite like previous testing report.

ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. PS/2 keyboard tested ok
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok

CPU0 CPU1 CPU2 CPU3

 29:          0          0          0          0          LSAPIC  cmc_poll
 30:          0          0          0          0  IO-SAPIC-level  cpe_hndlr
 31:          0          0          0          0          LSAPIC  cmc_hndlr
 32:        888         11          0          0   IO-SAPIC-edge  i8042
 33:        214          6          0          0   IO-SAPIC-edge  ide1
 34:         35          3          0          0   IO-SAPIC-edge  ide0
 36:       2527        100          9         16   IO-SAPIC-edge  i8042
 39:          4          0          0          0  IO-SAPIC-level  acpi
 45:         14          2          0          0   IO-SAPIC-edge  serial
 54:        621         34          0          0  IO-SAPIC-level  uhci_hcd
 55:        215          2          1          1  IO-SAPIC-level  eth0
 61:       5059        185          2         16  IO-SAPIC-level  qla1280
232:          0          0          0          0          LSAPIC  mca_rdzv
238:          0          0          0          0          LSAPIC  perfmon
239:     260134     255454     255013     254565          LSAPIC  timer
240:          0          0          0          0          LSAPIC  mca_wkup
254:         37        116        119        124          LSAPIC  IPI
NMI:          0          0          0          0 
ERR:          0

Problems:
1.PCI: no interrupt route for 00:00:03 pin B. (Known issue)

2.alloc 0x0-0xcf7 from PCI IO for PCI Bus 00:00 failed (Known issue)

<<dmesg.26.ZIP>> <<lspci.26.ZIP>> <<2.6.config.ZIP>>

author
#9 lore raw

Latest 2.6 IA64 Baseline (Mosberger) testing report (Tiger)

In reply to Yu, Luming

ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-Tiger
System Type: 4 way 900 Itanium2, tiger
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
MPT scsi host driver
Seagate ST318406LC boot drive
IDE floppy and CDROM
Serial console
USB mouse
USB keyboard
Ethernet Pro 1000

Software Configuration:
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 12/10(Shanghai time)
Nothing to pull
2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 12/10 (Shanghai time)
Nothing to pull
3. patch from http://bugzilla.kernel.org/show_bug.cgi?id=1634 to fix compile-time bug. Auto-merged without any manual work.

ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. ATI (run X window system) tested ok
4. usb keyboard tested ok
5. USB mouse tested ok
6. NIC (eg. Ping or ftp) tested ok
7. IDE (eg. r/w floppy or CDROM) tested ok
8. SCI (eg. Press power button) tested ok
9. Soft Power off tested ok

€€€€€€€€€€€€€€€€€ CPU0 CPU1 CPU2 CPU3

 34:          1          0          0         63   IO-SAPIC-edge  ide0
 39:          0          0          0          9  IO-SAPIC-level  acpi
 45:          0          4          0          3   IO-SAPIC-edge  serial
 48:          0          0          0          0  IO-SAPIC-level  ehci_hcd
 49:          1          7          0       1096  IO-SAPIC-level  uhci_hcd
 50:          0          0          0          0  IO-SAPIC-level  uhci_hcd
 51:          0         29          0        824  IO-SAPIC-level  eth0
 56:          4         56          0       4056  IO-SAPIC-level  ioc0
 57:          0          0          0         42  IO-SAPIC-level  ioc1
238:          0          0          0          0          LSAPIC  perfmon
239:     234862     229739     229290     228792          LSAPIC  timer
254:         37         89         92         94          LSAPIC  IPI
NMI:          0          0          0          0
ERR:          0

[Dmesg, /proc/interrupts, lspci -v , .config are attached in 2.4.log below]
<<2.6.ZIP>>