Latest 2.6 IA64 Baseline (Mosberger) testing report (Boot hang)
ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100
Software Configuration:
-----------------------
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/11 (Shanghai time) Successfully automerged by bk without out any manually work.
ACPI Features Tested: (prioritized).
--------------------
1. Boot hang
Kernel hang after message:
<<2.6.config.ZIP>>
"ELILO boot : Loading vmlinux... Done"
Thanks,
Luming
It boots fine on Lion here, it looks like you might be using the wrong config? The config you attached is for ZX1/McKinley.
Matt
Quoted 33 lines · Luming
ACPI Test Report for 2.6 ia64 kernel ============> Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100Software Configuration:
-----------------------1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/11 (Shanghai time) Successfully automerged by bk without out any manually work.ACPI Features Tested: (prioritized).
--------------------
1. Boot hangKernel hang after message:
<<2.6.config.ZIP>>
"ELILO boot : Loading vmlinux... Done"Thanks,
Luming
I double-checked my config file. You are right. After correcting this mistake, I can successfully boot 2.6 on lion.
Thanks
Luming
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Matt Chapman
Sent: 2003?11?13? 11:14
To: Yu, Luming
Cc: linux-acpi; [email protected]
Subject: Re: Latest 2.6 IA64 Baseline (Mosberger) testing report (Boot hang)
It boots fine on Lion here, it looks like you might be using the wrong config? The config you attached is for ZX1/McKinley.
Matt
Quoted 26 lines · Luming
ACPI Test Report for 2.6 ia64 kernel ============> Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100Software Configuration:
-----------------------1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/11 (Shanghai time) Successfully automerged by bk without out any manually work.ACPI Features Tested: (prioritized).
--------------------
1. Boot hang
Quoted 7 lines
Kernel hang after message:
<<2.6.config.ZIP>>
"ELILO boot : Loading vmlinux... Done"Thanks,
Luming
-
To unsubscribe from this list: send the line "unsubscribe linux-ia64" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100
Software Configuration:
-----------------------
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/19 (Shanghai time) 2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 11/19 (Shanghai time) Successfully automerged by bk without out any manually work. 3. patch from http://bugzilla.kernel.org/show_bug.cgi?id=1533 to solve kernel unaligned access when pressing power button
ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. PS/2 keyboard only work for a few minutes, then hang
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok
CPU0 CPU1 CPU2 CPU3
29: 0 0 0 0 LSAPIC cmc_poll 30: 0 0 0 0 IO-SAPIC-level cpe_hndlr 31: 0 0 0 0 LSAPIC cmc_hndlr 32: 724 4 32 0 IO-SAPIC-edge i8042 33: 493 0 9 0 IO-SAPIC-edge ide1 34: 34 0 4 0 IO-SAPIC-edge ide0 36: 777 31 46 0 IO-SAPIC-edge i8042 39: 2 0 0 0 IO-SAPIC-level acpi 44: 16 0 3 0 IO-SAPIC-edge serial 45: 14 0 3 0 IO-SAPIC-edge serial 54: 1656 9 78 2 IO-SAPIC-level uhci_hcd 55: 1032 5 55 1 IO-SAPIC-level eth0 61: 5520 13 279 1 IO-SAPIC-level qla1280 232: 0 0 0 0 LSAPIC mca_rdzv 238: 0 0 0 0 LSAPIC perfmon 239: 354543 349871 349425 348988 LSAPIC timer 240: 0 0 0 0 LSAPIC mca_wkup 254: 154 126 218 183 LSAPIC IPI NMI: 0 0 0 0 ERR: 0
Problems:
1. PS/2 keyboard only work for a few minutes, then hang.
2.alloc 0x0-0xcf7 from PCI IO for PCI Bus 0000:00 failed. (known issue)
3.ACPI: No IRQ known for interrupt pin B of device 0000:00:03.3. (Known issue)
<<dmesg.26.ZIP>> <<2.6.config.ZIP>> <<lspci.26.ZIP>>
Thanks,
Luming
RE: Latest 2.6 IA64 Baseline (Mosberger) testing report
In reply to Yu, LumingIt boot with any hang, but Leagcy keyboard hang. --Luming
Quoted 80 lines
-----Original Message-----
From: Yu, Luming
Sent: 2003Äê11ÔÂ19ÈÕ 20:43
To: linux-acpi
Cc: [email protected]
Subject: Latest 2.6 IA64 Baseline (Mosberger) testing report (Boot hang)ACPI Test Report for 2.6 ia64 kernel ============> Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100Software Configuration:
-----------------------1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/19 (Shanghai time) 2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 11/19 (Shanghai time) Successfully automerged by bk without out any manually work. 3. patch from http://bugzilla.kernel.org/show_bug.cgi?id33 to solve kernel unaligned access when pressing power buttonACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. PS/2 keyboard only work for a few minutes, then hang
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested okCPU0 CPU1 CPU2 CPU3
29: 0 0 0 0 LSAPIC cmc_poll 30: 0 0 0 0 IO-SAPIC-level cpe_hndlr 31: 0 0 0 0 LSAPIC cmc_hndlr 32: 724 4 32 0 IO-SAPIC-edge i8042 33: 493 0 9 0 IO-SAPIC-edge ide1 34: 34 0 4 0 IO-SAPIC-edge ide0 36: 777 31 46 0 IO-SAPIC-edge i8042 39: 2 0 0 0 IO-SAPIC-level acpi 44: 16 0 3 0 IO-SAPIC-edge serial 45: 14 0 3 0 IO-SAPIC-edge serial 54: 1656 9 78 2 IO-SAPIC-level uhci_hcd 55: 1032 5 55 1 IO-SAPIC-level eth0 61: 5520 13 279 1 IO-SAPIC-level qla1280 232: 0 0 0 0 LSAPIC mca_rdzv 238: 0 0 0 0 LSAPIC perfmon 239: 354543 349871 349425 348988 LSAPIC timer 240: 0 0 0 0 LSAPIC mca_wkup 254: 154 126 218 183 LSAPIC IPI NMI: 0 0 0 0 ERR: 0Problems:
1. PS/2 keyboard only work for a few minutes, then hang.
2.alloc 0x0-0xcf7 from PCI IO for PCI Bus 0000:00 failed. (known issue)
3.ACPI: No IRQ known for interrupt pin B of device 0000:00:03.3. (Known issue)
<< File: dmesg.26.TXT (Compressed) >> << File: 2.6.config.TXT (Compressed) >> << File: lspci.26.TXT (Compressed) >>
Thanks,
Luming
Latest 2.6 IA64 Baseline (Mosberger) testing report
In reply to Yu, LumingACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100
Software Configuration:
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 11/26 (Shanghai time) 2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 11/26 (Shanghai time) failed.
3. patch from http://bugzilla.kernel.org/show_bug.cgi?id=1533 to solve kernel unaligned access when pressing power button
ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console Didn't test
3. PS/2 keyboard tested ok
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok
CPU0 CPU1 CPU2 CPU3
29: 0 0 0 0 LSAPIC cmc_poll 30: 0 0 0 0 IO-SAPIC-level cpe_hndlr 31: 0 0 0 0 LSAPIC cmc_hndlr 32: 1379 4 0 10 IO-SAPIC-edge i8042 33: 583 19 0 11 IO-SAPIC-edge ide1 34: 22 10 0 6 IO-SAPIC-edge ide0 36: 565 1 0 53 IO-SAPIC-edge i8042 39: 5 0 0 0 IO-SAPIC-level acpi 45: 11 5 0 0 IO-SAPIC-edge serial 54: 2415 4 0 0 IO-SAPIC-level uhci_hcd 55: 2958 46 4 2 IO-SAPIC-level eth0 61: 9152 320 3 15 IO-SAPIC-level qla1280 232: 0 0 0 0 LSAPIC mca_rdzv 238: 0 0 0 0 LSAPIC perfmon 239: 1899520 1894834 1889372 1883893 LSAPIC timer 240: 0 0 0 0 LSAPIC mca_wkup 254: 84 135 109 128 LSAPIC IPI NMI: 0 0 0 0 ERR: 0
Problems:
1. Failed to bk pull http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 , Error message was
" Entire repository is locked by:
RESYNC directory.
ERROR-Unable to lock repository for update"
2.alloc 0x0-0xcf7 from PCI IO for PCI Bus 0000:00 failed. (known issue)
3.ACPI: No IRQ known for interrupt pin B of device 0000:00:03.3. (Known issue)
<<2.6.config.ZIP>> <<dmesg.26.ZIP>> <<lspci.26.ZIP>>
Thanks
Luming
Latest 2.6 IA64 Baseline (Mosberger) testing report (Lion)
In reply to Yu, LumingACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100
Software Configuration:
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 12/3 (Shanghai time) 2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 12/3 (Shanghai time)
3.patch from http://bugzilla.kernel.org/show_bug.cgi?id=1533 to solve kernel unaligned access when pressing power button Resolved 1 conflict by hand.(Take change from linux-ia64-2.5)
ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. PS/2 keyboard After about 5 minutes, keyboard doesn't respond.
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok
CPU0 CPU1 CPU2 CPU3
29: 0 0 0 0 LSAPIC cmc_poll 30: 0 0 0 0 IO-SAPIC-level cpe_hndlr 31: 0 0 0 0 LSAPIC cmc_hndlr 32: 1407 2 10 21 IO-SAPIC-edge i8042 33: 638 0 0 2 IO-SAPIC-edge ide1 34: 12 0 12 14 IO-SAPIC-edge ide0 36: 465 32 21 0 IO-SAPIC-edge i8042 39: 4 0 0 0 IO-SAPIC-level acpi 44: 6 0 0 2 IO-SAPIC-edge serial 45: 15 0 0 2 IO-SAPIC-edge serial 54: 2082 4 30 0 IO-SAPIC-level uhci_hcd 55: 2184 0 28 52 IO-SAPIC-level eth0 61: 8850 1 15 279 IO-SAPIC-level qla1280 232: 0 0 0 0 LSAPIC mca_rdzv 238: 0 0 0 0 LSAPIC perfmon 239: 727038 722365 716577 711104 LSAPIC timer 240: 0 0 0 0 LSAPIC mca_wkup 254: 141 165 273 267 LSAPIC IPI NMI: 0 0 0 0 ERR: 0
Problems:
1.After login about 5 minutes, keyboard doesn't respond.
2.PCI: no interrupt route for 00:00:03 pin B. (Known issue)
3. alloc 0x0-0xcf7 from PCI IO for PCI Bus 00:00 failed (Known issue)
4. ide-floppy: hda: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
ide-floppy: hda: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
<<lspci.26.ZIP>> <<dmesg.26.ZIP>> <<2.6.config.ZIP>>
Thanks,
Luming
Latest 2.6 IA64 Baseline (Mosberger) testing report (Tiger)
In reply to Yu, LumingACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-Tiger
System Type: 4 way 900 Itanium2, tiger
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
MPT scsi host driver
Seagate ST318406LC boot drive
IDE floppy and CDROM
Serial console
USB mouse
Ethernet Pro 1000
Software Configuration:
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 12/3 (Shanghai time) 2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 12/3 (Shanghai time) 3. patch from http://bugzilla.kernel.org/show_bug.cgi?id=1634 to fix compile-time bug. Resolved 1 conflict by hand.(Take change from linux-ia64-2.5)
ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. ATI (run X window system) tested ok
4. PS/2 mouse tested ok
5. USB mouse tested ok
6. NIC (eg. Ping or ftp) tested ok
7. IDE (eg. r/w floppy or CDROM) tested ok
8. SCI (eg. Press power button) tested ok
9. Soft Power off tested ok
CPU0 CPU1 CPU2 CPU3
29: 0 0 0 0 LSAPIC cmc_poll 30: 0 0 0 0 IO-SAPIC-level cpe_hndlr 31: 0 0 0 0 LSAPIC cmc_hndlr 34: 1 0 63 0 IO-SAPIC-edge ide0 39: 0 0 4 0 IO-SAPIC-level acpi 45: 0 1 94 0 IO-SAPIC-edge serial 48: 0 0 0 0 IO-SAPIC-level ehci_hcd 49: 1 24 1812 0 IO-SAPIC-level uhci_hcd 50: 0 0 40 0 IO-SAPIC-level uhci_hcd 51: 0 2 399 0 IO-SAPIC-level eth0 56: 7 128 3828 0 IO-SAPIC-level ioc0 57: 0 0 42 0 IO-SAPIC-level ioc1 232: 0 0 0 0 LSAPIC mca_rdzv 238: 0 0 0 0 LSAPIC perfmon 239: 203826 198715 198222 197807 LSAPIC timer 240: 0 0 0 0 LSAPIC mca_wkup 254: 34 94 87 91 LSAPIC IPI NMI: 0 0 0 0 ERR: 0
Problems:
Please refer dmesg attached .
[Dmesg, /proc/interrupts, lspci -v , .config are attached below]
<<2.6.ZIP>>
Thanks,
Luming
Latest 2.6 IA64 Baseline (Mosberger) testing report (Lion)
In reply to Yu, LumingACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-LION
System Type: 4 way 800M Itanium, Lion
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
QLogic QLA12160, Seagate ST39205LC boot drive IDE floppy and CDROM
Serial console
PS/2 keyboard and mouse
USB mouse
Ethernet Pro 100
Software Configuration:
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 12/10 (Shanghai time)
Nothing to pull
2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 12/10 (Shanghai time)
Nothing to pull
Since nothing to pull, test result is quite like previous testing report.
ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. PS/2 keyboard tested ok
4. ATI (run X window system) tested ok
5. PS/2 mouse tested ok
6. USB mouse tested ok
7. NIC (eg. Ping or ftp) tested ok
8. IDE (eg. r/w floppy or CDROM) tested ok
9. SCI (eg. Press power button) tested ok
10. Soft Power off tested ok
CPU0 CPU1 CPU2 CPU3
29: 0 0 0 0 LSAPIC cmc_poll 30: 0 0 0 0 IO-SAPIC-level cpe_hndlr 31: 0 0 0 0 LSAPIC cmc_hndlr 32: 888 11 0 0 IO-SAPIC-edge i8042 33: 214 6 0 0 IO-SAPIC-edge ide1 34: 35 3 0 0 IO-SAPIC-edge ide0 36: 2527 100 9 16 IO-SAPIC-edge i8042 39: 4 0 0 0 IO-SAPIC-level acpi 45: 14 2 0 0 IO-SAPIC-edge serial 54: 621 34 0 0 IO-SAPIC-level uhci_hcd 55: 215 2 1 1 IO-SAPIC-level eth0 61: 5059 185 2 16 IO-SAPIC-level qla1280 232: 0 0 0 0 LSAPIC mca_rdzv 238: 0 0 0 0 LSAPIC perfmon 239: 260134 255454 255013 254565 LSAPIC timer 240: 0 0 0 0 LSAPIC mca_wkup 254: 37 116 119 124 LSAPIC IPI NMI: 0 0 0 0 ERR: 0
Problems:
1.PCI: no interrupt route for 00:00:03 pin B. (Known issue)
2.alloc 0x0-0xcf7 from PCI IO for PCI Bus 00:00 failed (Known issue)
<<dmesg.26.ZIP>> <<lspci.26.ZIP>> <<2.6.config.ZIP>>
Latest 2.6 IA64 Baseline (Mosberger) testing report (Tiger)
In reply to Yu, LumingACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-Tiger
System Type: 4 way 900 Itanium2, tiger
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
MPT scsi host driver
Seagate ST318406LC boot drive
IDE floppy and CDROM
Serial console
USB mouse
USB keyboard
Ethernet Pro 1000
Software Configuration:
1.Bk pull form http://lia64.bkbits.net/linux-ia64-2.5 on 12/10(Shanghai time)
Nothing to pull
2.bk pull from http://linux-acpi.bkbits.net/linux-acpi-test-2.6.0 on 12/10 (Shanghai time)
Nothing to pull
3. patch from http://bugzilla.kernel.org/show_bug.cgi?id=1634 to fix compile-time bug. Auto-merged without any manual work.
ACPI Features Tested: (prioritized).
--------------------
1. Boot tested ok
2. serial console tested ok
3. ATI (run X window system) tested ok
4. usb keyboard tested ok
5. USB mouse tested ok
6. NIC (eg. Ping or ftp) tested ok
7. IDE (eg. r/w floppy or CDROM) tested ok
8. SCI (eg. Press power button) tested ok
9. Soft Power off tested ok
€€€€€€€€€€€€€€€€€ CPU0 CPU1 CPU2 CPU3
34: 1 0 0 63 IO-SAPIC-edge ide0 39: 0 0 0 9 IO-SAPIC-level acpi 45: 0 4 0 3 IO-SAPIC-edge serial 48: 0 0 0 0 IO-SAPIC-level ehci_hcd 49: 1 7 0 1096 IO-SAPIC-level uhci_hcd 50: 0 0 0 0 IO-SAPIC-level uhci_hcd 51: 0 29 0 824 IO-SAPIC-level eth0 56: 4 56 0 4056 IO-SAPIC-level ioc0 57: 0 0 0 42 IO-SAPIC-level ioc1 238: 0 0 0 0 LSAPIC perfmon 239: 234862 229739 229290 228792 LSAPIC timer 254: 37 89 92 94 LSAPIC IPI NMI: 0 0 0 0 ERR: 0
[Dmesg, /proc/interrupts, lspci -v , .config are attached in 2.4.log below]
<<2.6.ZIP>>