Upgrading Linux, Sound is Gone
I have an AOpen FX-3D sound board which I run in Sound Blaster emulation mode and it was working fine under Linux 2.0.34. I upgraded Linux to 2.0.36 and I can't get the sound to work.
Trying to initializing the sound board gives me:
sb: Interrupt test on IRQ7 failed - device disabled
I've tried fooling around with isapnptools but I don't get anywhere.
cat'ting /snd/sndstat gives:
Sound Driver:3.5.4-960630 (Thu Mar 18 21:23:59 EST 1999 root, Linux melake 2.0.36 #2 Tue Mar 16 17:51:55 EST 1999 i686 unknown)
Kernel: Linux melake 2.0.36 #6 Thu Mar 18 21:35:19 EST 1999 i686 Config options: 880002
Installed drivers:
Type 1: OPL-2/OPL-3 FM
Type 2: Sound Blaster
Card config:
Sound Blaster at 0x220 irq 7 drq 1,5
(OPL-2/OPL-3 FM at 0x388 drq 0)
Audio devices:
Synth devices:
Midi devices: NOT ENABLED IN CONFIG
Timers:
0: System clock
Mixers:
I had compiled 2.0.34 as i386. I compiled 2.0.36 as i686. Could that be making the difference?
Does anyone have any suggestions short of going back to 2.0.34?
Marshall Lake - [email protected] - http://melake.erols.com
http://melake.erols.com/~the-beach http://melake.erols.com/~genealogy
Usally IRQ is for the printer port. You might try disabling that in your BIOS.
For example, here are my interrupts:
0: 148784957 timer 1: 443152 keyboard 2: 0 cascade 3: 730500 NE2000 7: 11496998 sound blaster 12: 10422617 PS/2 Mouse 13: 1 math error
14: 10713065 + ide0
15: 28095811 + ide1
my ESS sound card is on IRQ 7 but I have my printer port disabled (or on a different IRQ) in my BIOS.
If you can change your printer port IRQ you have to disable it and install a printer port card.
-- Adrian St.Onge
Quoted 42 lines · Marshall Lake
I have an AOpen FX-3D sound board which I run in Sound Blaster emulation mode and it was working fine under Linux 2.0.34. I upgraded Linux to 2.0.36 and I can't get the sound to work.
Trying to initializing the sound board gives me:
sb: Interrupt test on IRQ7 failed - device disabledI've tried fooling around with isapnptools but I don't get anywhere.
cat'ting /snd/sndstat gives:
Sound Driver:3.5.4-960630 (Thu Mar 18 21:23:59 EST 1999 root, Linux melake 2.0.36 #2 Tue Mar 16 17:51:55 EST 1999 i686 unknown)
Kernel: Linux melake 2.0.36 #6 Thu Mar 18 21:35:19 EST 1999 i686 Config options: 880002Installed drivers:
Type 1: OPL-2/OPL-3 FM
Type 2: Sound BlasterCard config:
Sound Blaster at0x220irq 7 drq 1,5
(OPL-2/OPL-3 FM at0x388drq 0)Audio devices:
Synth devices:
Midi devices: NOT ENABLED IN CONFIG
Timers:
0: System clockMixers:
I had compiled 2.0.34 as i386. I compiled 2.0.36 as i686. Could that be making the difference?
Does anyone have any suggestions short of going back to 2.0.34?
Marshall Lake - [email protected] - http://melake.erols.com
http://melake.erols.com/~the-beach http://melake.erols.com/~genealogy