Skip to contentSkip to conversation

Upgrading Linux, Sound is Gone

DISCUSSION Marshall Lake 2 participants 2 messages Mar 19, 1999 – Mar 20, 1999 Sound

lore
Share & tools
lore
#0 lore raw

I have an AOpen FX-3D sound board which I run in Sound Blaster emulation mode and it was working fine under Linux 2.0.34. I upgraded Linux to 2.0.36 and I can't get the sound to work.

Trying to initializing the sound board gives me:
sb: Interrupt test on IRQ7 failed - device disabled

I've tried fooling around with isapnptools but I don't get anywhere.

cat'ting /snd/sndstat gives:
Sound Driver:3.5.4-960630 (Thu Mar 18 21:23:59 EST 1999 root, Linux melake 2.0.36 #2 Tue Mar 16 17:51:55 EST 1999 i686 unknown)
Kernel: Linux melake 2.0.36 #6 Thu Mar 18 21:35:19 EST 1999 i686 Config options: 880002

Installed drivers:
Type 1: OPL-2/OPL-3 FM
Type 2: Sound Blaster

Card config:
Sound Blaster at 0x220 irq 7 drq 1,5
(OPL-2/OPL-3 FM at 0x388 drq 0)

Audio devices:

Synth devices:

Midi devices: NOT ENABLED IN CONFIG

Timers:
0: System clock

Mixers:

I had compiled 2.0.34 as i386. I compiled 2.0.36 as i686. Could that be making the difference?

Does anyone have any suggestions short of going back to 2.0.34?

Marshall Lake - [email protected] - http://melake.erols.com
http://melake.erols.com/~the-beach http://melake.erols.com/~genealogy

#1 lore raw

Usally IRQ is for the printer port. You might try disabling that in your BIOS.
For example, here are my interrupts:

 0:  148784957   timer
 1:     443152   keyboard
 2:          0   cascade
 3:     730500   NE2000
 7:   11496998   sound blaster
12:   10422617   PS/2 Mouse
13:          1   math error

14: 10713065 + ide0
15: 28095811 + ide1

my ESS sound card is on IRQ 7 but I have my printer port disabled (or on a different IRQ) in my BIOS.
If you can change your printer port IRQ you have to disable it and install a printer port card.

-- Adrian St.Onge

Quoted 42 lines · Marshall Lake

I have an AOpen FX-3D sound board which I run in Sound Blaster emulation mode and it was working fine under Linux 2.0.34. I upgraded Linux to 2.0.36 and I can't get the sound to work.

Trying to initializing the sound board gives me:
sb: Interrupt test on IRQ7 failed - device disabled

I've tried fooling around with isapnptools but I don't get anywhere.

cat'ting /snd/sndstat gives:
Sound Driver:3.5.4-960630 (Thu Mar 18 21:23:59 EST 1999 root, Linux melake 2.0.36 #2 Tue Mar 16 17:51:55 EST 1999 i686 unknown)
Kernel: Linux melake 2.0.36 #6 Thu Mar 18 21:35:19 EST 1999 i686 Config options: 880002

Installed drivers:
Type 1: OPL-2/OPL-3 FM
Type 2: Sound Blaster

Card config:
Sound Blaster at 0x220 irq 7 drq 1,5
(OPL-2/OPL-3 FM at 0x388 drq 0)

Audio devices:

Synth devices:

Midi devices: NOT ENABLED IN CONFIG

Timers:
0: System clock

Mixers:

I had compiled 2.0.34 as i386. I compiled 2.0.36 as i686. Could that be making the difference?

Does anyone have any suggestions short of going back to 2.0.34?

Marshall Lake - [email protected] - http://melake.erols.com
http://melake.erols.com/~the-beach http://melake.erols.com/~genealogy