ARM: OMAP3: cm-t35: add EHCI support
Subsystems (3)
PATCH 1/1 ARM: OMAP3: cm-t35: add EHCI support
This patch adds support for EHCI on CM-T35.
It depends on basic CM-T35 board support ([1]) and EHCI updates in the linux-omap tree.
[1] http://thread.gmane.org/gmane.linux.ports.arm.omap/24938
---
--- arch/arm/mach-omap2/board-cm-t35.c | 17 +++++++++++++++++ 1 files changed, 17 insertions(+), 0 deletions(-)
arch/arm/mach-omap2/board-cm-t35.c +17 -0
@@ -352,6 +352,17 @@ static struct twl4030_hsmmc_info mmc[] = { {}/* Terminator */ }; +static struct ehci_hcd_omap_platform_data ehci_pdata = { + .port_mode[0 ] =EHCI_HCD_OMAP_MODE_PHY , + .port_mode[1 ] =EHCI_HCD_OMAP_MODE_PHY , + .port_mode[2 ] =EHCI_HCD_OMAP_MODE_UNKNOWN , + + .phy_reset = true, + .reset_gpio_port[0 ] = -EINVAL , + .reset_gpio_port[1 ] = -EINVAL , + .reset_gpio_port[2 ] = -EINVAL +}; +static int cm_t35_twl_gpio_setup (struct device *dev,unsigned gpio,unsigned ngpio) {
@@ -377,6 +388,12 @@ static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio, cm_t35_vmmc1_supply.dev = mmc[0 ].dev; cm_t35_vsim_supply.dev = mmc[0 ].dev; +/* setup USB with proper PHY reset GPIOs */ + ehci_pdata.reset_gpio_port[0 ] = gpio +6 ; + ehci_pdata.reset_gpio_port[1 ] = gpio +7 ; + +usb_ehci_init (&ehci_pdata); +return 0 ; }
Signature · 6 lines
1.6.0.6 -- Sincerely yours, Mike.
Tony Lindgren
maintainerPATCH 1/1 ARM: OMAP3: cm-t35: add EHCI support
This patch has been applied to the linux-omap
by youw fwiendly patch wobot.
Branch in linux-omap: ehci
Initial commit ID (Likely to change): 6a0dc193cf2e6055ffd9b1c34fa9f99e5836aabf
PatchWorks
http://patchwork.kernel.org/patch/53620/
Git (Likely to change, and takes a while to get mirrored)
http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=6a0dc193cf2e6055ffd9b1c34fa9f99e5836aabf
Quoted 17 lines
This patch adds support for EHCI on CM-T35.
It depends on basic CM-T35 board support ([1]) and EHCI updates in the linux-omap tree.[1] http://thread.gmane.org/gmane.linux.ports.arm.omap/24938
---Signed-off-by Mike Rapoport <[email protected]>--- arch/arm/mach-omap2/board-cm-t35.c | 17 +++++++++++++++++ 1 files changed, 17 insertions(+), 0 deletions(-)arch/arm/mach-omap2/board-cm-t35.c +0
-0
arch/arm/mach-omap2/board-cm-t35.c static struct twl4030_hsmmc_info mmc[] = { · line 359
Quoted 8 lines
arch/arm/mach-omap2/board-cm-t35.c +5
-0@@ -352,6 +352,17 @@ static struct twl4030_hsmmc_info mmc[] = { {}/* Terminator */ }; +static struct ehci_hcd_omap_platform_data ehci_pdata = { + .port_mode[0 ] =EHCI_HCD_OMAP_MODE_PHY , + .port_mode[1 ] =EHCI_HCD_OMAP_MODE_PHY , + .port_mode[2 ] =EHCI_HCD_OMAP_MODE_UNKNOWN , +
I haven't been following l-o for a while - I just got back. Is there a link to some documentation for this board (I'm just curious about the EHCI connections)?
Are you using Port1 and Port2 both? What PHY is connected to the ports?
arch/arm/mach-omap2/board-cm-t35.c static struct twl4030_hsmmc_info mmc[] = { · line 363
Quoted 4 lines
arch/arm/mach-omap2/board-cm-t35.c +4
-0+ .phy_reset = true, + .reset_gpio_port[0] = -EINVAL, + .reset_gpio_port[1 ] = -EINVAL , + .reset_gpio_port[2] = -EINVAL
You set these reset gpios below.
I guess you don't need to initialize them here.
- Anand
Quoted 27 lines
arch/arm/mach-omap2/board-cm-t35.c +8
-0+}; +static int cm_t35_twl_gpio_setup (struct device *dev,unsigned gpio,unsigned ngpio) {@@ -377,6 +388,12 @@ static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio, cm_t35_vmmc1_supply.dev = mmc[0 ].dev; cm_t35_vsim_supply.dev = mmc[0 ].dev; +/* setup USB with proper PHY reset GPIOs */ + ehci_pdata.reset_gpio_port[0 ] = gpio +6 ; + ehci_pdata.reset_gpio_port[1 ] = gpio +7 ; + +usb_ehci_init (&ehci_pdata); +return 0 ; }Signature · 6 lines
1.6.0.6 -- Sincerely yours, Mike.