snd_hda_intel on 2.6.16
Hi,
I read about a problem with snd_hda_intel latelly on 2.6.16. I was not having this on 2.6.15-19 but looks like it is "chip-monking"
I use linux2.6 git and it is still present. Just wanted to let you'll know about it.
Should anyone need any info, please let me know.
.Alejandro
Quoted 5 lines · Alejandro Bonilla
Hi,
I read about a problem with
snd_hda_intellatelly on 2.6.16. I was not having this on 2.6.15-19 but looks like it is "chip-monking"
Too cryptic. What exactly is the problem?
Quoted 5 lines
I use linux2.6 git and it is still present. Just wanted to let you'll know about it.
Should anyone need any info, please let me know.
Well, for starters, your hardware info ("hda-intel" describes 1000s of slightly different devices).
Does it work with the latest ALSA CVS or 1.0.11-rc4?
Lee
On Fri, 31 Mar 2006 11:40:58 -0500, Lee Revell wrote
Quoted 8 lines · Alejandro Bonilla
Quoted 5 lines
Hi,
I read about a problem with
snd_hda_intellatelly on 2.6.16. I was not having this on 2.6.15-19 but looks like it is "chip-monking"Too cryptic. What exactly is the problem?
The sound is like at 1.2x. Just a little bit faster but noticeable.
Quoted 9 lines
Quoted 6 lines
I use linux2.6 git and it is still present. Just wanted to let you'll know about it.
Should anyone need any info, please let me know.
Well, for starters, your hardware info ("hda-intel" describes 1000s of slightly different devices).
0000:00:1b.0 0403: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 30a0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 50
Region 0: Memory at d8240000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] #10 [0091]
Pretty much, I almost only know it is Conexant.
Quoted 2 lines
Does it work with the latest ALSA CVS or 1.0.11-rc4?
I don't know. It was working with 2.6.15-X
.Alejandro
Quoted 2 lines
Lee
Quoted 3 lines · Alejandro Bonilla
Quoted 1 line
Does it work with the latest ALSA CVS or 1.0.11-rc4?
I don't know. It was working with 2.6.15-X
Please test ALSA CVS or 1.0.11-rc4.
Lee
Quoted 4 lines · Alejandro Bonilla
Quoted 1 line
Does it work with the latest ALSA CVS or 1.0.11-rc4?
I don't know. It was working with 2.6.15-X
Disregard last message, it's probably easiest to test the [ALSA PATCH] that was just posted.
Lee
On Fri, 31 Mar 2006 12:07:12 -0500, Lee Revell wrote
Quoted 8 lines · Alejandro Bonilla
Quoted 4 lines
Quoted 1 line
Does it work with the latest ALSA CVS or 1.0.11-rc4?
I don't know. It was working with 2.6.15-X
Disregard last message, it's probably easiest to test the [ALSA PATCH] that was just posted.
I will git fetch soon and see if it got merged and test that out.
Thanks,
.Alejandro
Quoted 2 lines
Lee
At Fri, 31 Mar 2006 10:49:19 -0600,
Quoted 5 lines · Alejandro Bonilla
On Fri, 31 Mar 2006 11:40:58 -0500, Lee Revell wrote
Quoted 3 lines · Alejandro Bonilla
Quoted 2 lines
Hi,
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
I read about a problem with
snd_hda_intellatelly on 2.6.16. I was not having this on 2.6.15-19 but looks like it is "chip-monking"Too cryptic. What exactly is the problem?
The sound is like at 1.2x. Just a little bit faster but noticeable.
Faster? You mean pitch or only playback speed?
It's the first report I've heard. Usually, the regression is either noisy output or silence...
Try position_fix=1, or a different value, if the latest ALSA version still doesn't work.
Quoted 27 lines
Quoted 8 lines
Quoted 5 lines
I use linux2.6 git and it is still present. Just wanted to let you'll know about it.
Should anyone need any info, please let me know.
Well, for starters, your hardware info ("hda-intel" describes 1000s of slightly different devices).
0000:00:1b.0 0403: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 30a0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size:0x10(64 bytes)
Interrupt: pin A routed to IRQ 50
Region 0: Memory atd8240000(64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] #10 [0091]
Quoted 1 line
Pretty much, I almost only know it is Conexant.
Better check /proc/asound/card0/codec#* files.
Sigh, Conexant. It's a problematic one. They don't give any technical information.
Quoted 4 lines
Quoted 2 lines
Does it work with the latest ALSA CVS or 1.0.11-rc4?
I don't know. It was working with 2.6.15-X
Any other changes on your system except for kernel?
Takashi
On Fri, 31 Mar 2006 19:47:43 +0200, Takashi Iwai wrote
Quoted 8 lines
At Fri, 31 Mar 2006 10:49:19 -0600,
Quoted 6 lines · Alejandro Bonilla
On Fri, 31 Mar 2006 11:40:58 -0500, Lee Revell wrote
Quoted 4 lines · Alejandro Bonilla
Quoted 3 lines
Hi,
I read about a problem with
snd_hda_intellatelly on 2.6.16. I was not
having
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
this on 2.6.15-19 but looks like it is "chip-monking"
Too cryptic. What exactly is the problem?
The sound is like at 1.2x. Just a little bit faster but noticeable.
Faster? You mean pitch or only playback speed?
Yes, it is just a bit faster. In speed.
Quoted 5 lines
It's the first report I've heard. Usually, the regression is either noisy output or silence...
Try position_fix=1, or a different value, if the latest ALSA version still doesn't work.
root@ubuntu:~# echo 1 > /sys/bus/pci/drivers/HDA\ Intel/module/parameters/position_fix -bash: /sys/bus/pci/drivers/HDA Intel/module/parameters/position_fix: Permission denied
It might take me awhile to unload all the modules and try loading it again. :) I'll get back to you.
and
I will try the new patch when gets merged.
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
Quoted 6 lines
I use linux2.6 git and it is still present. Just wanted to let you'll know about it.
Should anyone need any info, please let me know.
Well, for starters, your hardware info ("hda-intel" describes 1000s of slightly different devices).
Quoted 15 lines
Quoted 7 lines
0000:00:1b.0 0403: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 30a0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-Quoted 8 lines
Latency: 0, Cache Line Size:
0x10(64 bytes)
Interrupt: pin A routed to IRQ 50
Region 0: Memory atd8240000(64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Quoted 6 lines
Quoted 4 lines
Address: 0000000000000000 Data: 0000 Capabilities: [70] #10 [0091]Pretty much, I almost only know it is Conexant.
Better check /proc/asound/card0/codec#* files.
The file is too big, any hint of what you might want to look at?
Quoted 3 lines
Sigh, Conexant. It's a problematic one. They don't give any technical information.
:|
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Does it work with the latest ALSA CVS or 1.0.11-rc4?
I don't know. It was working with 2.6.15-X
Any other changes on your system except for kernel?
No, if I boot back to 2.6.15-19 it works.
Quoted 2 lines
Takashi
--
Open WebMail Project (http://openwebmail.org)