spi: spi-mem: Add driver for Aspeed SMC controllers
Get series with b4
b4 am [email protected]Versions newest first · linked by author and title
- v3 Latest11 patches 0 repliesNew
- v210 patches 15 repliesSuperseded
- v110 patches 46 repliesSuperseded
Changes in v3 from the cover letter
- Fixed compile warning on aspeed_spi_dirmap_read() prototype reported by kernel test robot
- Removed unnecessary entry in ast2600-fmc.yaml
- New patch from Tao to set spi-max-frequency on all FMC devices
Patches in v3 No applies recorded yet
| # | Subject and files | Size | Replies | Applied |
|---|---|---|---|---|
| 1/11 | mtd: spi-nor: aspeed: Rename Kconfig optiondrivers/ drivers/ | +2 | 0 replies | |
| 2/11 | ARM: dts: aspeed: Adjust "reg" property of FMC/SPI controllersarch/ arch/ arch/ | +8 | 0 replies | |
| 3/11 | dt-bindings: spi: Add Aspeed SMC controllers device tree bindingDocumentation/ MAINTAINERS | +96 | 0 replies | |
| 4/11 | spi: spi-mem: Add driver for Aspeed SMC controllersMAINTAINERS drivers/ drivers/ +2 more | +723 | 0 replies | |
| 5/11 | spi: aspeed: Add support for direct mappingdrivers/ | +65 | 0 replies | |
| 6/11 | spi: aspeed: Adjust direct mapping to device sizedrivers/ | +88 | 0 replies | |
| 7/11 | spi: aspeed: Workaround AST2500 limitationsdrivers/ | +12 | 0 replies | |
| 8/11 | spi: aspeed: Add support for the AST2400 SPI controllerdrivers/ | +32 | 0 replies | |
| 9/11 | spi: aspeed: Calibrate read timingsdrivers/ | +281 | 0 replies | |
| 10/11 | ARM: dts: aspeed: Enable Dual SPI RX transfersarch/ arch/ arch/ | +21 | 0 replies | |
| 11/11 | ARM: dts: aspeed-g4: Set spi-max-frequency for all flashesarch/ | +4 | 0 replies |
Reviews trailers per patch
9 of 11 patches have a Reviewed-by or Acked-by.
| Patch | Joel Stanley | Tao Ren | Rob Herring |
|---|---|---|---|
| 1/11 | R-b T-b | T-b | |
| 2/11 | T-b | T-b | |
| 3/11 | T-b R-b | T-b | R-b |
| 4/11 | R-b T-b | T-b | |
| 5/11 | R-b T-b | T-b | |
| 6/11 | R-b T-b | T-b | |
| 7/11 | R-b T-b | T-b | |
| 8/11 | R-b T-b | T-b | |
| 9/11 | R-b T-b | T-b | |
| 10/11 | R-b T-b | T-b | |
| 11/11 |
Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes. Scroll the table sideways for all 3 reviewers.
Cover letter [PATCH v3 00/11] spi: spi-mem: Add driver for Aspeed SMC controllers
Hi,
This series adds a new SPI driver using the spi-mem interface for the Aspeed static memory controllers of the AST2600, AST2500 and AST2400 SoCs.
* AST2600 Firmware SPI Memory Controller (FMC)
* AST2600 SPI Flash Controller (SPI1 and SPI2)
* AST2500 Firmware SPI Memory Controller (FMC)
* AST2500 SPI Flash Controller (SPI1 and SPI2)
* AST2400 New Static Memory Controller (also referred as FMC)
* AST2400 SPI Flash Controller (SPI)
It is based on the current OpenBMC kernel driver [1], using directly the MTD SPI-NOR interface and on a patchset [2] previously proposed adding support for the AST2600 only. This driver takes a slightly different approach to cover all 6 controllers.
It does not make use of the controller register disabling Address and Data byte lanes because is not available on the AST2400 SoC. We could introduce a specific handler for new features available on recent SoCs if needed. As there is not much difference on performance, the driver chooses the common denominator: "User mode" which has been heavily tested in [1]. "User mode" is also used as a fall back method when flash device mapping window is too small.
Problems to address with spi-mem were the configuration of the mapping windows and the calibration of the read timings. The driver handles them in the direct mapping handler when some knowledge on the size of the flash device is know. It is not perfect but not incorrect either. The algorithm is one from [1] because it doesn't require the DMA registers which are not available on all controllers.
Direct mapping for writes is not supported (yet). I have seen some corruption with writes and I preferred to use the safer and proven method of the initial driver [1]. We can improve that later.
The driver supports Quad SPI RX transfers on the AST2600 SoC but it didn't have the expected results. Therefore it is not activated yet. There are some issues on the pinctrl to investigate first.
The series does not remove the current Aspeed SMC driver but prepares ground for its removal by changing its CONFIG option. This last step can be addressed as a followup when the new driver using the spi-mem interface has been sufficiently exposed.
Tested on:
* OpenPOWER Palmetto (AST2400)
* Facebook Wedge 100 BMC (AST2400) by Tao Ren <[email protected]>
* Evaluation board (AST2500)
* Inspur FP5280G2 BMC (AST2500) by John Wang <[email protected]>
* Facebook Backpack CMM BMC (AST2500) by Tao Ren <[email protected]>
* OpenPOWER Witherspoon (AST2500)
* Evaluation board (AST2600 A0 and A3)
* Rainier board (AST2600)
[1] https://github.com/openbmc/linux/blob/dev-5.15/drivers/mtd/spi-nor/controllers/aspeed-smc.c
[2] https://patchwork.ozlabs.org/project/linux-aspeed/list/?series=212394
Thanks,
C.
Changes in v3:
- Fixed compile warning on aspeed_spi_dirmap_read() prototype reported by kernel test robot
- Removed unnecessary entry in ast2600-fmc.yaml
- New patch from Tao to set spi-max-frequency on all FMC devices
Changes in v2:
- Fixed dt_binding_check warnings (Rob)
- New entry in MAINTAINERS
- Addressed Lukas comments regarding the SPI controller registration and device removal. Checked with driver bind/unbind
- Introduced setup and cleanup handlers and removed routine looping on the DT children properties (Pratyush)
- Clarified in commit log requirements for training.
- Removed defconfig changes of patch 1 since they were reverted in the last patch (Joel)
C?dric Le Goater (10):
mtd: spi-nor: aspeed: Rename Kconfig option
ARM: dts: aspeed: Adjust "reg" property of FMC/SPI controllers
dt-bindings: spi: Add Aspeed SMC controllers device tree binding
spi: spi-mem: Add driver for Aspeed SMC controllers
spi: aspeed: Add support for direct mapping
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Calibrate read timings
ARM: dts: aspeed: Enable Dual SPI RX transfers
Tao Ren (1):
ARM: dts: aspeed-g4: Set spi-max-frequency for all flashes
drivers/spi/spi-aspeed-smc.c | 1184 +++++++++++++++++ .../bindings/spi/aspeed,ast2600-fmc.yaml | 87 ++ MAINTAINERS | 10 + arch/arm/boot/dts/aspeed-g4.dtsi | 16 +- arch/arm/boot/dts/aspeed-g5.dtsi | 16 +- arch/arm/boot/dts/aspeed-g6.dtsi | 17 +- drivers/mtd/spi-nor/controllers/Kconfig | 4 +- drivers/mtd/spi-nor/controllers/Makefile | 2 +- drivers/spi/Kconfig | 11 + drivers/spi/Makefile | 1 + 10 files changed, 1329 insertions(+), 19 deletions(-) create mode 100644 drivers/spi/spi-aspeed-smc.c create mode 100644 Documentation/devicetree/bindings/spi/aspeed,ast2600-fmc.yaml
Signature · 1 line
2.34.1