Skip to contentSkip to conversation

spi: spi-mem: Add driver for Aspeed SMC controllers

PATCH New Cédric Le Goater 1 participant 12 messages Mar 4, 2022

Subsystems (6)
lore
Share & tools
lore

Cédric Le Goater

author maintainer
#0 lore raw

v3 cover spi: spi-mem: Add driver for Aspeed SMC controllers

Hi,

This series adds a new SPI driver using the spi-mem interface for the Aspeed static memory controllers of the AST2600, AST2500 and AST2400 SoCs.

* AST2600 Firmware SPI Memory Controller (FMC)
* AST2600 SPI Flash Controller (SPI1 and SPI2)
* AST2500 Firmware SPI Memory Controller (FMC)
* AST2500 SPI Flash Controller (SPI1 and SPI2)
* AST2400 New Static Memory Controller (also referred as FMC)
* AST2400 SPI Flash Controller (SPI)

It is based on the current OpenBMC kernel driver [1], using directly the MTD SPI-NOR interface and on a patchset [2] previously proposed adding support for the AST2600 only. This driver takes a slightly different approach to cover all 6 controllers.

It does not make use of the controller register disabling Address and Data byte lanes because is not available on the AST2400 SoC. We could introduce a specific handler for new features available on recent SoCs if needed. As there is not much difference on performance, the driver chooses the common denominator: "User mode" which has been heavily tested in [1]. "User mode" is also used as a fall back method when flash device mapping window is too small.

Problems to address with spi-mem were the configuration of the mapping windows and the calibration of the read timings. The driver handles them in the direct mapping handler when some knowledge on the size of the flash device is know. It is not perfect but not incorrect either. The algorithm is one from [1] because it doesn't require the DMA registers which are not available on all controllers.

Direct mapping for writes is not supported (yet). I have seen some corruption with writes and I preferred to use the safer and proven method of the initial driver [1]. We can improve that later.

The driver supports Quad SPI RX transfers on the AST2600 SoC but it didn't have the expected results. Therefore it is not activated yet. There are some issues on the pinctrl to investigate first.

The series does not remove the current Aspeed SMC driver but prepares ground for its removal by changing its CONFIG option. This last step can be addressed as a followup when the new driver using the spi-mem interface has been sufficiently exposed.

Tested on:

* OpenPOWER Palmetto (AST2400)
* Facebook Wedge 100 BMC (AST2400) by Tao Ren <[email protected]>
* Evaluation board (AST2500)
* Inspur FP5280G2 BMC (AST2500) by John Wang <[email protected]>
* Facebook Backpack CMM BMC (AST2500) by Tao Ren <[email protected]>
* OpenPOWER Witherspoon (AST2500)
* Evaluation board (AST2600 A0 and A3)
* Rainier board (AST2600)

[1] https://github.com/openbmc/linux/blob/dev-5.15/drivers/mtd/spi-nor/controllers/aspeed-smc.c
[2] https://patchwork.ozlabs.org/project/linux-aspeed/list/?series=212394

Thanks,

C.

Changes in v3:

- Fixed compile warning on aspeed_spi_dirmap_read() prototype reported by kernel test robot
- Removed unnecessary entry in ast2600-fmc.yaml
- New patch from Tao to set spi-max-frequency on all FMC devices

Changes in v2:

- Fixed dt_binding_check warnings (Rob)
- New entry in MAINTAINERS
- Addressed Lukas comments regarding the SPI controller registration and device removal. Checked with driver bind/unbind
- Introduced setup and cleanup handlers and removed routine looping on the DT children properties (Pratyush)
- Clarified in commit log requirements for training.
- Removed defconfig changes of patch 1 since they were reverted in the last patch (Joel)

C?dric Le Goater (10):
mtd: spi-nor: aspeed: Rename Kconfig option
ARM: dts: aspeed: Adjust "reg" property of FMC/SPI controllers
dt-bindings: spi: Add Aspeed SMC controllers device tree binding
spi: spi-mem: Add driver for Aspeed SMC controllers
spi: aspeed: Add support for direct mapping
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Calibrate read timings
ARM: dts: aspeed: Enable Dual SPI RX transfers

Tao Ren (1):
ARM: dts: aspeed-g4: Set spi-max-frequency for all flashes

 drivers/spi/spi-aspeed-smc.c                  | 1184 +++++++++++++++++
 .../bindings/spi/aspeed,ast2600-fmc.yaml      |   87 ++
 MAINTAINERS                                   |   10 +
 arch/arm/boot/dts/aspeed-g4.dtsi              |   16 +-
 arch/arm/boot/dts/aspeed-g5.dtsi              |   16 +-
 arch/arm/boot/dts/aspeed-g6.dtsi              |   17 +-
 drivers/mtd/spi-nor/controllers/Kconfig       |    4 +-
 drivers/mtd/spi-nor/controllers/Makefile      |    2 +-
 drivers/spi/Kconfig                           |   11 +
 drivers/spi/Makefile                          |    1 +
 10 files changed, 1329 insertions(+), 19 deletions(-)
 create mode 100644 drivers/spi/spi-aspeed-smc.c
 create mode 100644 Documentation/devicetree/bindings/spi/aspeed,ast2600-fmc.yaml
Signature · 1 line
2.34.1
author maintainer
#1 lore raw

PATCH v3 1/11 mtd: spi-nor: aspeed: Rename Kconfig option

To prepare transition to the new Aspeed SMC SPI controller driver using the spi-mem interface, change the kernel CONFIG option of the current driver to reflect that the implementation uses the MTD SPI-NOR interface. Once the new driver is sufficiently exposed, we should remove the old one.

---
 drivers/mtd/spi-nor/controllers/Kconfig  | 2 +-
 drivers/mtd/spi-nor/controllers/Makefile | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)
drivers/mtd/spi-nor/controllers/Kconfig +1 -1
index 5c0e0ec2e6d1..876a47042fec 100644
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0-only
-config SPI_ASPEED_SMC
+config SPI_ASPEED_SMC_MTD_SPI_NOR
 	tristate "Aspeed flash controllers in SPI mode"
 	depends on ARCH_ASPEED || COMPILE_TEST
 	depends on HAS_IOMEM && OF
drivers/mtd/spi-nor/controllers/Makefile +1 -1
index e7abba491d98..1e28297fb1e8 100644
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_SPI_ASPEED_SMC)	+= aspeed-smc.o
+obj-$(CONFIG_SPI_ASPEED_SMC_MTD_SPI_NOR)	+= aspeed-smc.o
 obj-$(CONFIG_SPI_HISI_SFC)	+= hisi-sfc.o
 obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
 obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
Signature · 1 line
2.34.1
author maintainer
#2 lore raw

PATCH v3 2/11 ARM: dts: aspeed: Adjust "reg" property of FMC/SPI controllers

In reply to Cédric Le Goater

This is compatible with the current driver and addresses issues when running 'make dt_binding_check'.

---
 arch/arm/boot/dts/aspeed-g4.dtsi | 6 ++----
 arch/arm/boot/dts/aspeed-g5.dtsi | 9 +++------
 arch/arm/boot/dts/aspeed-g6.dtsi | 9 +++------
 3 files changed, 8 insertions(+), 16 deletions(-)
arch/arm/boot/dts/aspeed-g4.dtsi +2 -4
index f14dace34c5a..9ae67e83cf60 100644
@@ -54,8 +54,7 @@ ahb {
 		ranges;
 
 		fmc: spi at 1e620000 {
-			reg = < 0x1e620000 0x94
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0x94>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2400-fmc";
@@ -91,8 +90,7 @@ flash at 4 {
 		};
 
 		spi: spi at 1e630000 {
-			reg = < 0x1e630000 0x18
-				0x30000000 0x10000000 >;
+			reg = <0x1e630000 0x18>, <0x30000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2400-spi";
arch/arm/boot/dts/aspeed-g5.dtsi +3 -6
index 7495f93c5069..c3e0a8e13c8a 100644
@@ -55,8 +55,7 @@ ahb {
 		ranges;
 
 		fmc: spi at 1e620000 {
-			reg = < 0x1e620000 0xc4
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-fmc";
@@ -84,8 +83,7 @@ flash at 2 {
 		};
 
 		spi1: spi at 1e630000 {
-			reg = < 0x1e630000 0xc4
-				0x30000000 0x08000000 >;
+			reg = <0x1e630000 0xc4>, <0x30000000 0x08000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-spi";
@@ -106,8 +104,7 @@ flash at 1 {
 		};
 
 		spi2: spi at 1e631000 {
-			reg = < 0x1e631000 0xc4
-				0x38000000 0x08000000 >;
+			reg = <0x1e631000 0xc4>, <0x38000000 0x08000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-spi";
arch/arm/boot/dts/aspeed-g6.dtsi +3 -6
index c32e87fad4dc..1ad05dde19d2 100644
@@ -95,8 +95,7 @@ gic: interrupt-controller at 40461000 {
 			};
 
 		fmc: spi at 1e620000 {
-			reg = < 0x1e620000 0xc4
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-fmc";
@@ -124,8 +123,7 @@ flash at 2 {
 		};
 
 		spi1: spi at 1e630000 {
-			reg = < 0x1e630000 0xc4
-				0x30000000 0x10000000 >;
+			reg = <0x1e630000 0xc4>, <0x30000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-spi";
@@ -146,8 +144,7 @@ flash at 1 {
 		};
 
 		spi2: spi at 1e631000 {
-			reg = < 0x1e631000 0xc4
-				0x50000000 0x10000000 >;
+			reg = <0x1e631000 0xc4>, <0x50000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-spi";
Signature · 1 line
2.34.1
author maintainer
#3 lore raw

PATCH v3 3/11 dt-bindings: spi: Add Aspeed SMC controllers device tree binding

In reply to Cédric Le Goater

The "interrupt" property is optional because it is only necessary for controllers supporting DMAs (Not implemented yet in the new driver).

---
 .../bindings/spi/aspeed,ast2600-fmc.yaml      | 87 +++++++++++++++++++
 MAINTAINERS                                   |  9 ++
 2 files changed, 96 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/aspeed,ast2600-fmc.yaml
Documentation/devicetree/bindings/spi/aspeed,ast2600-fmc.yaml new file +87 -0
new file mode 100644
index 000000000000..e16bbcd38560
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/aspeed,ast2600-fmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Aspeed SMC controllers bindings
+
+maintainers:
+  - Chin-Ting Kuo <[email protected]>
+  - C?dric Le Goater <[email protected]>
+
+description: |
+  This binding describes the Aspeed Static Memory Controllers (FMC and
+  SPI) of the AST2400, AST2500 and AST2600 SOCs.
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+properties:
+  compatible:
+    enum:
+      - aspeed,ast2600-fmc
+      - aspeed,ast2600-spi
+      - aspeed,ast2500-fmc
+      - aspeed,ast2500-spi
+      - aspeed,ast2400-fmc
+      - aspeed,ast2400-spi
+
+  reg:
+    items:
+      - description: registers
+      - description: memory mapping
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+patternProperties:
+  "@[0-9a-f]+":
+    type: object
+
+    properties:
+      spi-rx-bus-width:
+        enum: [1, 2, 4]
+
+required:
+  - compatible
+  - reg
+  - clocks
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/aspeed-scu-ic.h>
+    #include <dt-bindings/clock/ast2600-clock.h>
+
+    spi at 1e620000 {
+        reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        compatible = "aspeed,ast2600-fmc";
+        clocks = <&syscon ASPEED_CLK_AHB>;
+        interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+        flash at 0 {
+                reg = < 0 >;
+                compatible = "jedec,spi-nor";
+                spi-max-frequency = <50000000>;
+                spi-rx-bus-width = <2>;
+        };
+        flash at 1 {
+                reg = < 1 >;
+                compatible = "jedec,spi-nor";
+                spi-max-frequency = <50000000>;
+                spi-rx-bus-width = <2>;
+        };
+        flash at 2 {
+                reg = < 2 >;
+                compatible = "jedec,spi-nor";
+                spi-max-frequency = <50000000>;
+                spi-rx-bus-width = <2>;
+        };
+    };
MAINTAINERS +9 -0
index 4175103e928d..f5ab77548ef6 100644
@@ -2925,6 +2925,15 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/mmc/aspeed,sdhci.yaml
 F:	drivers/mmc/host/sdhci-of-aspeed*
 
+ASPEED SMC SPI DRIVER
+M:	Chin-Ting Kuo <[email protected]>
+M:	C?dric Le Goater <[email protected]>
+L:	linux-aspeed at lists.ozlabs.org (moderated for non-subscribers)
+L:	openbmc at lists.ozlabs.org (moderated for non-subscribers)
+L:	linux-spi at vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/spi/aspeed,ast2600-fmc.yaml
+
 ASPEED VIDEO ENGINE DRIVER
 M:	Eddie James <[email protected]>
 L:	linux-media at vger.kernel.org
Signature · 1 line
2.34.1
author maintainer
#4 lore raw

PATCH v3 4/11 spi: spi-mem: Add driver for Aspeed SMC controllers

In reply to Cédric Le Goater

This SPI driver adds support for the Aspeed static memory controllers of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.

* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.

* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.

* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver . single, dual mode.

* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.

* AST2400 New Static Memory Controller (also referred as FMC) . BMC firmware
. New register set
. 5 chip select pins (CE0 ? CE4)
. supports NOR flash, NAND flash and SPI flash memory. . single, dual and quad mode.

Each controller has a memory range on which flash devices contents are mapped. Each device is assigned a window that can be changed at bootime with the Segment Address Registers.

Each SPI flash device can then be accessed in two modes: Command and User. When in User mode, SPI transfers are initiated with accesses to the memory segment of a device. When in Command mode, memory operations on the memory segment of a device generate SPI commands automatically using a Control Register for the settings.

This initial patch adds support for User mode. Command mode needs a little more work to check that the memory window on the AHB bus fits the device size. It will come later when support for direct mapping is added.

Single and dual mode RX transfers are supported. Other types than SPI are not supported.

---
 drivers/spi/spi-aspeed-smc.c            | 709 ++++++++++++++++++++++++
 MAINTAINERS                             |   1 +
 drivers/mtd/spi-nor/controllers/Kconfig |   2 +-
 drivers/spi/Kconfig                     |  11 +
 drivers/spi/Makefile                    |   1 +
 5 files changed, 723 insertions(+), 1 deletion(-)
 create mode 100644 drivers/spi/spi-aspeed-smc.c
drivers/spi/spi-aspeed-smc.c new file +709 -0
new file mode 100644
index 000000000000..997ec2e45118
@@ -0,0 +1,709 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * ASPEED FMC/SPI Memory Controller Driver
+ *
+ * Copyright (c) 2015-2022, IBM Corporation.
+ * Copyright (c) 2020, ASPEED Corporation.
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+#define DEVICE_NAME "spi-aspeed-smc"
+
+/* Type setting Register */
+#define CONFIG_REG			0x0
+#define   CONFIG_TYPE_SPI		0x2
+
+/* CE Control Register */
+#define CE_CTRL_REG			0x4
+
+/* CEx Control Register */
+#define CE0_CTRL_REG			0x10
+#define   CTRL_IO_MODE_MASK		GENMASK(30, 28)
+#define   CTRL_IO_SINGLE_DATA	        0x0
+#define   CTRL_IO_DUAL_DATA		BIT(29)
+#define   CTRL_IO_QUAD_DATA		BIT(30)
+#define   CTRL_COMMAND_SHIFT		16
+#define   CTRL_IO_DUMMY_SET(dummy)					\
+	(((((dummy) >> 2) & 0x1) << 14) | (((dummy) & 0x3) << 6))
+#define   CTRL_CE_STOP_ACTIVE		BIT(2)
+#define   CTRL_IO_MODE_CMD_MASK		GENMASK(1, 0)
+#define   CTRL_IO_MODE_NORMAL		0x0
+#define   CTRL_IO_MODE_READ		0x1
+#define   CTRL_IO_MODE_WRITE		0x2
+#define   CTRL_IO_MODE_USER		0x3
+
+#define   CTRL_IO_CMD_MASK		0xf0ff40c3
+
+/* CEx Address Decoding Range Register */
+#define CE0_SEGMENT_ADDR_REG		0x30
+
+enum aspeed_spi_ctl_reg_value {
+	ASPEED_SPI_BASE,
+	ASPEED_SPI_READ,
+	ASPEED_SPI_WRITE,
+	ASPEED_SPI_MAX,
+};
+
+struct aspeed_spi;
+
+struct aspeed_spi_chip {
+	struct aspeed_spi	*aspi;
+	u32			 cs;
+	void __iomem		*ctl;
+	void __iomem		*ahb_base;
+	u32			 ahb_window_size;
+	u32			 ctl_val[ASPEED_SPI_MAX];
+	u32			 clk_freq;
+};
+
+struct aspeed_spi_data {
+	u32	ctl0;
+	u32	max_cs;
+	bool	hastype;
+	u32	mode_bits;
+	u32	we0;
+
+	u32 (*segment_start)(struct aspeed_spi *aspi, u32 reg);
+	u32 (*segment_end)(struct aspeed_spi *aspi, u32 reg);
+	u32 (*segment_reg)(struct aspeed_spi *aspi, u32 start, u32 end);
+};
+
+#define ASPEED_SPI_MAX_NUM_CS	5
+
+struct aspeed_spi {
+	const struct aspeed_spi_data	*data;
+
+	void __iomem		*regs;
+	void __iomem		*ahb_base;
+	u32			 ahb_base_phy;
+	u32			 ahb_window_size;
+	struct device		*dev;
+
+	struct clk		*clk;
+	u32			 clk_freq;
+
+	struct aspeed_spi_chip	 chips[ASPEED_SPI_MAX_NUM_CS];
+};
+
+static u32 aspeed_spi_get_io_mode(const struct spi_mem_op *op)
+{
+	switch (op->data.buswidth) {
+	case 1:
+		return CTRL_IO_SINGLE_DATA;
+	case 2:
+		return CTRL_IO_DUAL_DATA;
+	case 4:
+		return CTRL_IO_QUAD_DATA;
+	default:
+		return CTRL_IO_SINGLE_DATA;
+	}
+}
+
+static void aspeed_spi_set_io_mode(struct aspeed_spi_chip *chip, u32 io_mode)
+{
+	u32 ctl;
+
+	if (io_mode > 0) {
+		ctl = readl(chip->ctl) & ~CTRL_IO_MODE_MASK;
+		ctl |= io_mode;
+		writel(ctl, chip->ctl);
+	}
+}
+
+static void aspeed_spi_start_user(struct aspeed_spi_chip *chip)
+{
+	u32 ctl = chip->ctl_val[ASPEED_SPI_BASE];
+
+	ctl |= CTRL_IO_MODE_USER | CTRL_CE_STOP_ACTIVE;
+	writel(ctl, chip->ctl);
+
+	ctl &= ~CTRL_CE_STOP_ACTIVE;
+	writel(ctl, chip->ctl);
+}
+
+static void aspeed_spi_stop_user(struct aspeed_spi_chip *chip)
+{
+	u32 ctl = chip->ctl_val[ASPEED_SPI_READ] |
+		CTRL_IO_MODE_USER | CTRL_CE_STOP_ACTIVE;
+
+	writel(ctl, chip->ctl);
+
+	/* Restore defaults */
+	writel(chip->ctl_val[ASPEED_SPI_READ], chip->ctl);
+}
+
+static int aspeed_spi_read_from_ahb(void *buf, void __iomem *src, size_t len)
+{
+	size_t offset = 0;
+
+	if (IS_ALIGNED((uintptr_t)src, sizeof(uintptr_t)) &&
+	    IS_ALIGNED((uintptr_t)buf, sizeof(uintptr_t))) {
+		ioread32_rep(src, buf, len >> 2);
+		offset = len & ~0x3;
+		len -= offset;
+	}
+	ioread8_rep(src, (u8 *)buf + offset, len);
+	return 0;
+}
+
+static int aspeed_spi_write_to_ahb(void __iomem *dst, const void *buf, size_t len)
+{
+	size_t offset = 0;
+
+	if (IS_ALIGNED((uintptr_t)dst, sizeof(uintptr_t)) &&
+	    IS_ALIGNED((uintptr_t)buf, sizeof(uintptr_t))) {
+		iowrite32_rep(dst, buf, len >> 2);
+		offset = len & ~0x3;
+		len -= offset;
+	}
+	iowrite8_rep(dst, (const u8 *)buf + offset, len);
+	return 0;
+}
+
+static void aspeed_spi_send_cmd_addr(struct aspeed_spi_chip *chip, u8 addr_nbytes,
+				     u64 offset, u32 opcode)
+{
+	struct aspeed_spi *aspi = chip->aspi;
+	__be32 temp;
+	u32 cmdaddr;
+
+	switch (addr_nbytes) {
+	default:
+		dev_warn_once(aspi->dev, "Unexpected address width %u, defaulting to 3",
+			      addr_nbytes);
+		fallthrough;
+	case 3:
+		cmdaddr = offset & 0xFFFFFF;
+		cmdaddr |= opcode << 24;
+
+		temp = cpu_to_be32(cmdaddr);
+		aspeed_spi_write_to_ahb(chip->ahb_base, &temp, 4);
+		break;
+	case 4:
+		temp = cpu_to_be32(offset);
+		aspeed_spi_write_to_ahb(chip->ahb_base, &opcode, 1);
+		aspeed_spi_write_to_ahb(chip->ahb_base, &temp, 4);
+		break;
+	}
+}
+
+static int aspeed_spi_read_reg(struct aspeed_spi_chip *chip,
+			       const struct spi_mem_op *op)
+{
+	aspeed_spi_start_user(chip);
+	aspeed_spi_write_to_ahb(chip->ahb_base, &op->cmd.opcode, 1);
+	aspeed_spi_read_from_ahb(op->data.buf.in,
+				 chip->ahb_base, op->data.nbytes);
+	aspeed_spi_stop_user(chip);
+	return 0;
+}
+
+static int aspeed_spi_write_reg(struct aspeed_spi_chip *chip,
+				const struct spi_mem_op *op)
+{
+	aspeed_spi_start_user(chip);
+	aspeed_spi_write_to_ahb(chip->ahb_base, &op->cmd.opcode, 1);
+	aspeed_spi_write_to_ahb(chip->ahb_base, op->data.buf.out,
+				op->data.nbytes);
+	aspeed_spi_stop_user(chip);
+	return 0;
+}
+
+static ssize_t aspeed_spi_read_user(struct aspeed_spi_chip *chip,
+				    const struct spi_mem_op *op,
+				    u64 offset, size_t len, void *buf)
+{
+	int io_mode = aspeed_spi_get_io_mode(op);
+	u8 dummy = 0xFF;
+	int i;
+
+	aspeed_spi_start_user(chip);
+	aspeed_spi_send_cmd_addr(chip, op->addr.nbytes, offset, op->cmd.opcode);
+	if (op->dummy.buswidth && op->dummy.nbytes) {
+		for (i = 0; i < op->dummy.nbytes / op->dummy.buswidth; i++)
+			aspeed_spi_write_to_ahb(chip->ahb_base, &dummy,	sizeof(dummy));
+	}
+
+	aspeed_spi_set_io_mode(chip, io_mode);
+
+	aspeed_spi_read_from_ahb(buf, chip->ahb_base, len);
+	aspeed_spi_stop_user(chip);
+	return 0;
+}
+
+static ssize_t aspeed_spi_write_user(struct aspeed_spi_chip *chip,
+				     const struct spi_mem_op *op)
+{
+	aspeed_spi_start_user(chip);
+	aspeed_spi_send_cmd_addr(chip, op->addr.nbytes, op->addr.val, op->cmd.opcode);
+	aspeed_spi_write_to_ahb(chip->ahb_base, op->data.buf.out, op->data.nbytes);
+	aspeed_spi_stop_user(chip);
+	return 0;
+}
+
+/* support for 1-1-1, 1-1-2 or 1-1-4 */
+static bool aspeed_spi_supports_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	if (op->cmd.buswidth > 1)
+		return false;
+
+	if (op->addr.nbytes != 0) {
+		if (op->addr.buswidth > 1 || op->addr.nbytes > 4)
+			return false;
+	}
+
+	if (op->dummy.nbytes != 0) {
+		if (op->dummy.buswidth > 1 || op->dummy.nbytes > 7)
+			return false;
+	}
+
+	if (op->data.nbytes != 0 && op->data.buswidth > 4)
+		return false;
+
+	return spi_mem_default_supports_op(mem, op);
+}
+
+static int do_aspeed_spi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct aspeed_spi *aspi = spi_controller_get_devdata(mem->spi->master);
+	struct aspeed_spi_chip *chip = &aspi->chips[mem->spi->chip_select];
+	u32 addr_mode, addr_mode_backup;
+	u32 ctl_val;
+	int ret = 0;
+
+	dev_dbg(aspi->dev,
+		"CE%d %s OP %#x mode:%d.%d.%d.%d naddr:%#x ndummies:%#x len:%#x",
+		chip->cs, op->data.dir == SPI_MEM_DATA_IN ? "read" : "write",
+		op->cmd.opcode, op->cmd.buswidth, op->addr.buswidth,
+		op->dummy.buswidth, op->data.buswidth,
+		op->addr.nbytes, op->dummy.nbytes, op->data.nbytes);
+
+	addr_mode = readl(aspi->regs + CE_CTRL_REG);
+	addr_mode_backup = addr_mode;
+
+	ctl_val = chip->ctl_val[ASPEED_SPI_BASE];
+	ctl_val &= ~CTRL_IO_CMD_MASK;
+
+	ctl_val |= op->cmd.opcode << CTRL_COMMAND_SHIFT;
+
+	/* 4BYTE address mode */
+	if (op->addr.nbytes) {
+		if (op->addr.nbytes == 4)
+			addr_mode |= (0x11 << chip->cs);
+		else
+			addr_mode &= ~(0x11 << chip->cs);
+	}
+
+	if (op->dummy.buswidth && op->dummy.nbytes)
+		ctl_val |= CTRL_IO_DUMMY_SET(op->dummy.nbytes / op->dummy.buswidth);
+
+	if (op->data.nbytes != 0) {
+		if (op->data.buswidth)
+			ctl_val |= aspeed_spi_get_io_mode(op);
+	}
+
+	if (op->data.dir == SPI_MEM_DATA_OUT)
+		ctl_val |= CTRL_IO_MODE_WRITE;
+	else
+		ctl_val |= CTRL_IO_MODE_READ;
+
+	if (addr_mode != addr_mode_backup)
+		writel(addr_mode, aspi->regs + CE_CTRL_REG);
+	writel(ctl_val, chip->ctl);
+
+	if (op->data.dir == SPI_MEM_DATA_IN) {
+		if (!op->addr.nbytes)
+			ret = aspeed_spi_read_reg(chip, op);
+		else
+			ret = aspeed_spi_read_user(chip, op, op->addr.val,
+						   op->data.nbytes, op->data.buf.in);
+	} else {
+		if (!op->addr.nbytes)
+			ret = aspeed_spi_write_reg(chip, op);
+		else
+			ret = aspeed_spi_write_user(chip, op);
+	}
+
+	/* Restore defaults */
+	if (addr_mode != addr_mode_backup)
+		writel(addr_mode_backup, aspi->regs + CE_CTRL_REG);
+	writel(chip->ctl_val[ASPEED_SPI_READ], chip->ctl);
+	return ret;
+}
+
+static int aspeed_spi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	int ret;
+
+	ret = do_aspeed_spi_exec_op(mem, op);
+	if (ret)
+		dev_err(&mem->spi->dev, "operation failed: %d\n", ret);
+	return ret;
+}
+
+static const char *aspeed_spi_get_name(struct spi_mem *mem)
+{
+	struct aspeed_spi *aspi = spi_controller_get_devdata(mem->spi->master);
+	struct device *dev = aspi->dev;
+
+	return devm_kasprintf(dev, GFP_KERNEL, "%s.%d", dev_name(dev), mem->spi->chip_select);
+}
+
+struct aspeed_spi_window {
+	u32 cs;
+	u32 offset;
+	u32 size;
+};
+
+static void aspeed_spi_get_windows(struct aspeed_spi *aspi,
+				   struct aspeed_spi_window windows[ASPEED_SPI_MAX_NUM_CS])
+{
+	const struct aspeed_spi_data *data = aspi->data;
+	u32 reg_val;
+	u32 cs;
+
+	for (cs = 0; cs < aspi->data->max_cs; cs++) {
+		reg_val = readl(aspi->regs + CE0_SEGMENT_ADDR_REG + cs * 4);
+		windows[cs].cs = cs;
+		windows[cs].size = data->segment_end(aspi, reg_val) -
+			data->segment_start(aspi, reg_val);
+		windows[cs].offset = cs ? windows[cs - 1].offset + windows[cs - 1].size : 0;
+		dev_vdbg(aspi->dev, "CE%d offset=0x%.8x size=0x%x\n", cs,
+			 windows[cs].offset, windows[cs].size);
+	}
+}
+
+/*
+ * On the AST2600, some CE windows are closed by default at reset but
+ * U-Boot should open all.
+ */
+static int aspeed_spi_chip_set_default_window(struct aspeed_spi_chip *chip)
+{
+	struct aspeed_spi *aspi = chip->aspi;
+	struct aspeed_spi_window windows[ASPEED_SPI_MAX_NUM_CS] = { 0 };
+	struct aspeed_spi_window *win = &windows[chip->cs];
+
+	aspeed_spi_get_windows(aspi, windows);
+
+	chip->ahb_base = aspi->ahb_base + win->offset;
+	chip->ahb_window_size = win->size;
+
+	dev_dbg(aspi->dev, "CE%d default window [ 0x%.8x - 0x%.8x ] %dMB",
+		chip->cs, aspi->ahb_base_phy + win->offset,
+		aspi->ahb_base_phy + win->offset + win->size - 1,
+		win->size >> 20);
+
+	return chip->ahb_window_size ? 0 : -1;
+}
+
+static const struct spi_controller_mem_ops aspeed_spi_mem_ops = {
+	.supports_op = aspeed_spi_supports_op,
+	.exec_op = aspeed_spi_exec_op,
+	.get_name = aspeed_spi_get_name,
+};
+
+static void aspeed_spi_chip_set_type(struct aspeed_spi *aspi, unsigned int cs, int type)
+{
+	u32 reg;
+
+	reg = readl(aspi->regs + CONFIG_REG);
+	reg &= ~(0x3 << (cs * 2));
+	reg |= type << (cs * 2);
+	writel(reg, aspi->regs + CONFIG_REG);
+}
+
+static void aspeed_spi_chip_enable(struct aspeed_spi *aspi, unsigned int cs, bool enable)
+{
+	u32 we_bit = BIT(aspi->data->we0 + cs);
+	u32 reg = readl(aspi->regs + CONFIG_REG);
+
+	if (enable)
+		reg |= we_bit;
+	else
+		reg &= ~we_bit;
+	writel(reg, aspi->regs + CONFIG_REG);
+}
+
+static int aspeed_spi_setup(struct spi_device *spi)
+{
+	struct aspeed_spi *aspi = spi_controller_get_devdata(spi->master);
+	const struct aspeed_spi_data *data = aspi->data;
+	unsigned int cs = spi->chip_select;
+	struct aspeed_spi_chip *chip = &aspi->chips[cs];
+
+	chip->aspi = aspi;
+	chip->cs = cs;
+	chip->ctl = aspi->regs + data->ctl0 + cs * 4;
+
+	/* The driver only supports SPI type flash */
+	if (data->hastype)
+		aspeed_spi_chip_set_type(aspi, cs, CONFIG_TYPE_SPI);
+
+	if (aspeed_spi_chip_set_default_window(chip) < 0) {
+		dev_warn(aspi->dev, "CE%d window invalid", cs);
+		return -EINVAL;
+	}
+
+	aspeed_spi_chip_enable(aspi, cs, true);
+
+	chip->ctl_val[ASPEED_SPI_BASE] = CTRL_CE_STOP_ACTIVE | CTRL_IO_MODE_USER;
+
+	dev_dbg(aspi->dev, "CE%d setup done\n", cs);
+	return 0;
+}
+
+static void aspeed_spi_cleanup(struct spi_device *spi)
+{
+	struct aspeed_spi *aspi = spi_controller_get_devdata(spi->master);
+	unsigned int cs = spi->chip_select;
+
+	aspeed_spi_chip_enable(aspi, cs, false);
+
+	dev_dbg(aspi->dev, "CE%d cleanup done\n", cs);
+}
+
+static void aspeed_spi_enable(struct aspeed_spi *aspi, bool enable)
+{
+	int cs;
+
+	for (cs = 0; cs < aspi->data->max_cs; cs++)
+		aspeed_spi_chip_enable(aspi, cs, enable);
+}
+
+static int aspeed_spi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct aspeed_spi_data *data;
+	struct spi_controller *ctlr;
+	struct aspeed_spi *aspi;
+	struct resource *res;
+	int ret;
+
+	data = of_device_get_match_data(&pdev->dev);
+	if (!data)
+		return -ENODEV;
+
+	ctlr = devm_spi_alloc_master(dev, sizeof(*aspi));
+	if (!ctlr)
+		return -ENOMEM;
+
+	aspi = spi_controller_get_devdata(ctlr);
+	platform_set_drvdata(pdev, aspi);
+	aspi->data = data;
+	aspi->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	aspi->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(aspi->regs)) {
+		dev_err(dev, "missing AHB register window\n");
+		return PTR_ERR(aspi->regs);
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	aspi->ahb_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(aspi->ahb_base)) {
+		dev_err(dev, "missing AHB mapping window\n");
+		return PTR_ERR(aspi->ahb_base);
+	}
+
+	aspi->ahb_window_size = resource_size(res);
+	aspi->ahb_base_phy = res->start;
+
+	aspi->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(aspi->clk)) {
+		dev_err(dev, "missing clock\n");
+		return PTR_ERR(aspi->clk);
+	}
+
+	aspi->clk_freq = clk_get_rate(aspi->clk);
+	if (!aspi->clk_freq) {
+		dev_err(dev, "invalid clock\n");
+		return -EINVAL;
+	}
+
+	ret = clk_prepare_enable(aspi->clk);
+	if (ret) {
+		dev_err(dev, "can not enable the clock\n");
+		return ret;
+	}
+
+	/* IRQ is for DMA, which the driver doesn't support yet */
+
+	ctlr->mode_bits = SPI_RX_DUAL | SPI_TX_DUAL | data->mode_bits;
+	ctlr->bus_num = pdev->id;
+	ctlr->mem_ops = &aspeed_spi_mem_ops;
+	ctlr->setup = aspeed_spi_setup;
+	ctlr->cleanup = aspeed_spi_cleanup;
+	ctlr->num_chipselect = data->max_cs;
+	ctlr->dev.of_node = dev->of_node;
+
+	ret = devm_spi_register_controller(dev, ctlr);
+	if (ret) {
+		dev_err(&pdev->dev, "spi_register_controller failed\n");
+		goto disable_clk;
+	}
+	return 0;
+
+disable_clk:
+	clk_disable_unprepare(aspi->clk);
+	return ret;
+}
+
+static int aspeed_spi_remove(struct platform_device *pdev)
+{
+	struct aspeed_spi *aspi = platform_get_drvdata(pdev);
+
+	aspeed_spi_enable(aspi, false);
+	clk_disable_unprepare(aspi->clk);
+	return 0;
+}
+
+/*
+ * AHB mappings
+ */
+
+/*
+ * The Segment Registers of the AST2400 and AST2500 use a 8MB unit.
+ * The address range is encoded with absolute addresses in the overall
+ * mapping window.
+ */
+static u32 aspeed_spi_segment_start(struct aspeed_spi *aspi, u32 reg)
+{
+	return ((reg >> 16) & 0xFF) << 23;
+}
+
+static u32 aspeed_spi_segment_end(struct aspeed_spi *aspi, u32 reg)
+{
+	return ((reg >> 24) & 0xFF) << 23;
+}
+
+static u32 aspeed_spi_segment_reg(struct aspeed_spi *aspi, u32 start, u32 end)
+{
+	return (((start >> 23) & 0xFF) << 16) | (((end >> 23) & 0xFF) << 24);
+}
+
+/*
+ * The Segment Registers of the AST2600 use a 1MB unit. The address
+ * range is encoded with offsets in the overall mapping window.
+ */
+
+#define AST2600_SEG_ADDR_MASK 0x0ff00000
+
+static u32 aspeed_spi_segment_ast2600_start(struct aspeed_spi *aspi,
+					    u32 reg)
+{
+	u32 start_offset = (reg << 16) & AST2600_SEG_ADDR_MASK;
+
+	return aspi->ahb_base_phy + start_offset;
+}
+
+static u32 aspeed_spi_segment_ast2600_end(struct aspeed_spi *aspi,
+					  u32 reg)
+{
+	u32 end_offset = reg & AST2600_SEG_ADDR_MASK;
+
+	/* segment is disabled */
+	if (!end_offset)
+		return aspi->ahb_base_phy;
+
+	return aspi->ahb_base_phy + end_offset + 0x100000;
+}
+
+static u32 aspeed_spi_segment_ast2600_reg(struct aspeed_spi *aspi,
+					  u32 start, u32 end)
+{
+	/* disable zero size segments */
+	if (start == end)
+		return 0;
+
+	return ((start & AST2600_SEG_ADDR_MASK) >> 16) |
+		((end - 1) & AST2600_SEG_ADDR_MASK);
+}
+
+/*
+ * Platform definitions
+ */
+static const struct aspeed_spi_data ast2400_fmc_data = {
+	.max_cs	       = 5,
+	.hastype       = true,
+	.we0	       = 16,
+	.ctl0	       = CE0_CTRL_REG,
+	.segment_start = aspeed_spi_segment_start,
+	.segment_end   = aspeed_spi_segment_end,
+	.segment_reg   = aspeed_spi_segment_reg,
+};
+
+static const struct aspeed_spi_data ast2500_fmc_data = {
+	.max_cs	       = 3,
+	.hastype       = true,
+	.we0	       = 16,
+	.ctl0	       = CE0_CTRL_REG,
+	.segment_start = aspeed_spi_segment_start,
+	.segment_end   = aspeed_spi_segment_end,
+	.segment_reg   = aspeed_spi_segment_reg,
+};
+
+static const struct aspeed_spi_data ast2500_spi_data = {
+	.max_cs	       = 2,
+	.hastype       = false,
+	.we0	       = 16,
+	.ctl0	       = CE0_CTRL_REG,
+	.segment_start = aspeed_spi_segment_start,
+	.segment_end   = aspeed_spi_segment_end,
+	.segment_reg   = aspeed_spi_segment_reg,
+};
+
+static const struct aspeed_spi_data ast2600_fmc_data = {
+	.max_cs	       = 3,
+	.hastype       = false,
+	.mode_bits     = SPI_RX_QUAD | SPI_RX_QUAD,
+	.we0	       = 16,
+	.ctl0	       = CE0_CTRL_REG,
+	.segment_start = aspeed_spi_segment_ast2600_start,
+	.segment_end   = aspeed_spi_segment_ast2600_end,
+	.segment_reg   = aspeed_spi_segment_ast2600_reg,
+};
+
+static const struct aspeed_spi_data ast2600_spi_data = {
+	.max_cs	       = 2,
+	.hastype       = false,
+	.mode_bits     = SPI_RX_QUAD | SPI_RX_QUAD,
+	.we0	       = 16,
+	.ctl0	       = CE0_CTRL_REG,
+	.segment_start = aspeed_spi_segment_ast2600_start,
+	.segment_end   = aspeed_spi_segment_ast2600_end,
+	.segment_reg   = aspeed_spi_segment_ast2600_reg,
+};
+
+static const struct of_device_id aspeed_spi_matches[] = {
+	{ .compatible = "aspeed,ast2400-fmc", .data = &ast2400_fmc_data },
+	{ .compatible = "aspeed,ast2500-fmc", .data = &ast2500_fmc_data },
+	{ .compatible = "aspeed,ast2500-spi", .data = &ast2500_spi_data },
+	{ .compatible = "aspeed,ast2600-fmc", .data = &ast2600_fmc_data },
+	{ .compatible = "aspeed,ast2600-spi", .data = &ast2600_spi_data },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, aspeed_spi_matches);
+
+static struct platform_driver aspeed_spi_driver = {
+	.probe			= aspeed_spi_probe,
+	.remove			= aspeed_spi_remove,
+	.driver	= {
+		.name		= DEVICE_NAME,
+		.of_match_table = aspeed_spi_matches,
+	}
+};
+
+module_platform_driver(aspeed_spi_driver);
+
+MODULE_DESCRIPTION("ASPEED Static Memory Controller Driver");
+MODULE_AUTHOR("Chin-Ting Kuo <[email protected]>");
+MODULE_AUTHOR("Cedric Le Goater <[email protected]>");
+MODULE_LICENSE("GPL v2");
MAINTAINERS +1 -0
index f5ab77548ef6..cb163052fe61 100644
@@ -2933,6 +2933,7 @@ L:	openbmc at lists.ozlabs.org (moderated for non-subscribers)
 L:	linux-spi at vger.kernel.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/spi/aspeed,ast2600-fmc.yaml
+F:	drivers/spi/spi-aspeed-smc.c
 
 ASPEED VIDEO ENGINE DRIVER
 M:	Eddie James <[email protected]>
drivers/mtd/spi-nor/controllers/Kconfig +1 -1
index 876a47042fec..35f18c01b1d8 100644
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config SPI_ASPEED_SMC_MTD_SPI_NOR
 	tristate "Aspeed flash controllers in SPI mode"
-	depends on ARCH_ASPEED || COMPILE_TEST
+	depends on (ARCH_ASPEED && !SPI_ASPEED_SMC) || COMPILE_TEST
 	depends on HAS_IOMEM && OF
 	help
 	  This enables support for the Firmware Memory controller (FMC)
drivers/spi/Kconfig +11 -0
index 83e352b0c8f9..dc44493439fb 100644
@@ -101,6 +101,17 @@ config SPI_ARMADA_3700
 	  This enables support for the SPI controller present on the
 	  Marvell Armada 3700 SoCs.
 
+config SPI_ASPEED_SMC
+	tristate "Aspeed flash controllers in SPI mode"
+	depends on (ARCH_ASPEED && !CONFIG_SPI_ASPEED_SMC_MTD_SPI_NOR) || COMPILE_TEST
+	depends on OF
+	help
+	  This enables support for the Firmware Memory controller (FMC)
+	  in the Aspeed AST2600, AST2500 and AST2400 SoCs when attached
+	  to SPI NOR chips, and support for the SPI flash memory
+	  controller (SPI) for the host firmware. The implementation
+	  only supports SPI NOR.
+
 config SPI_ATMEL
 	tristate "Atmel SPI Controller"
 	depends on ARCH_AT91 || COMPILE_TEST
drivers/spi/Makefile +1 -0
index 699db95c8441..3dd0e649be94 100644
@@ -19,6 +19,7 @@ obj-$(CONFIG_SPI_ALTERA_CORE)		+= spi-altera-core.o
 obj-$(CONFIG_SPI_ALTERA_DFL)		+= spi-altera-dfl.o
 obj-$(CONFIG_SPI_AR934X)		+= spi-ar934x.o
 obj-$(CONFIG_SPI_ARMADA_3700)		+= spi-armada-3700.o
+obj-$(CONFIG_SPI_ASPEED_SMC)		+= spi-aspeed-smc.o
 obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATMEL_QUADSPI)		+= atmel-quadspi.o
 obj-$(CONFIG_SPI_AT91_USART)		+= spi-at91-usart.o
Signature · 1 line
2.34.1
author maintainer
#5 lore raw

PATCH v3 5/11 spi: aspeed: Add support for direct mapping

In reply to Cédric Le Goater

Use direct mapping to read the flash device contents. This operation mode is called "Command mode" on Aspeed SoC SMC controllers. It uses a Control Register for the settings to apply when a memory operation is performed on the flash device mapping window.

If the window is not big enough, fall back to the "User mode" to perform the read.

Since direct mapping now handles all reads of the flash device contents, also use memcpy_fromio for other address spaces, such as SFDP.

Direct mapping for writes will come later when validated.

---
 drivers/spi/spi-aspeed-smc.c | 67 ++++++++++++++++++++++++++++++++++--
 1 file changed, 65 insertions(+), 2 deletions(-)
drivers/spi/spi-aspeed-smc.c +65 -2
index 997ec2e45118..0951766baef4 100644
@@ -322,8 +322,8 @@ static int do_aspeed_spi_exec_op(struct spi_mem *mem, const struct spi_mem_op *o
 		if (!op->addr.nbytes)
 			ret = aspeed_spi_read_reg(chip, op);
 		else
-			ret = aspeed_spi_read_user(chip, op, op->addr.val,
-						   op->data.nbytes, op->data.buf.in);
+			memcpy_fromio(op->data.buf.in, chip->ahb_base + op->addr.val,
+				      op->data.nbytes);
 	} else {
 		if (!op->addr.nbytes)
 			ret = aspeed_spi_write_reg(chip, op);
@@ -403,10 +403,73 @@ static int aspeed_spi_chip_set_default_window(struct aspeed_spi_chip *chip)
 	return chip->ahb_window_size ? 0 : -1;
 }
 
+static int aspeed_spi_dirmap_create(struct spi_mem_dirmap_desc *desc)
+{
+	struct aspeed_spi *aspi = spi_controller_get_devdata(desc->mem->spi->master);
+	struct aspeed_spi_chip *chip = &aspi->chips[desc->mem->spi->chip_select];
+	struct spi_mem_op *op = &desc->info.op_tmpl;
+	u32 ctl_val;
+	int ret = 0;
+
+	chip->clk_freq = desc->mem->spi->max_speed_hz;
+
+	/* Only for reads */
+	if (op->data.dir != SPI_MEM_DATA_IN)
+		return -EOPNOTSUPP;
+
+	if (desc->info.length > chip->ahb_window_size)
+		dev_warn(aspi->dev, "CE%d window (%dMB) too small for mapping",
+			 chip->cs, chip->ahb_window_size >> 20);
+
+	/* Define the default IO read settings */
+	ctl_val = readl(chip->ctl) & ~CTRL_IO_CMD_MASK;
+	ctl_val |= aspeed_spi_get_io_mode(op) |
+		op->cmd.opcode << CTRL_COMMAND_SHIFT |
+		CTRL_IO_DUMMY_SET(op->dummy.nbytes / op->dummy.buswidth) |
+		CTRL_IO_MODE_READ;
+
+	/* Tune 4BYTE address mode */
+	if (op->addr.nbytes) {
+		u32 addr_mode = readl(aspi->regs + CE_CTRL_REG);
+
+		if (op->addr.nbytes == 4)
+			addr_mode |= (0x11 << chip->cs);
+		else
+			addr_mode &= ~(0x11 << chip->cs);
+		writel(addr_mode, aspi->regs + CE_CTRL_REG);
+	}
+
+	/* READ mode is the controller default setting */
+	chip->ctl_val[ASPEED_SPI_READ] = ctl_val;
+	writel(chip->ctl_val[ASPEED_SPI_READ], chip->ctl);
+
+	dev_info(aspi->dev, "CE%d read buswidth:%d [0x%08x]\n",
+		 chip->cs, op->data.buswidth, chip->ctl_val[ASPEED_SPI_READ]);
+
+	return ret;
+}
+
+static ssize_t aspeed_spi_dirmap_read(struct spi_mem_dirmap_desc *desc,
+				      u64 offset, size_t len, void *buf)
+{
+	struct aspeed_spi *aspi = spi_controller_get_devdata(desc->mem->spi->master);
+	struct aspeed_spi_chip *chip = &aspi->chips[desc->mem->spi->chip_select];
+
+	/* Switch to USER command mode if mapping window is too small */
+	if (chip->ahb_window_size < offset + len)
+		aspeed_spi_read_user(chip, &desc->info.op_tmpl, offset, len, buf);
+	else
+		memcpy_fromio(buf, chip->ahb_base + offset, len);
+
+	return len;
+}
+
 static const struct spi_controller_mem_ops aspeed_spi_mem_ops = {
 	.supports_op = aspeed_spi_supports_op,
 	.exec_op = aspeed_spi_exec_op,
 	.get_name = aspeed_spi_get_name,
+	.dirmap_create = aspeed_spi_dirmap_create,
+	.dirmap_read = aspeed_spi_dirmap_read,
 };
 
 static void aspeed_spi_chip_set_type(struct aspeed_spi *aspi, unsigned int cs, int type)
Signature · 1 line
2.34.1
author maintainer
#6 lore raw

PATCH v3 6/11 spi: aspeed: Adjust direct mapping to device size

In reply to Cédric Le Goater

The segment registers of the FMC/SPI controllers provide a way to configure the mapping window of the flash device contents on the AHB bus. Adjust this window to the size of the spi-mem mapping.

Things get more complex with multiple devices. The driver needs to also adjust the window of the next device to make sure that there is no overlap, even if there is no available device. The proposal below is not perfect but it is covering all the cases we have seen on different boards with one and two devices on the same bus.

---
 drivers/spi/spi-aspeed-smc.c | 88 ++++++++++++++++++++++++++++++++++++
 1 file changed, 88 insertions(+)
drivers/spi/spi-aspeed-smc.c +88 -0
index 0951766baef4..9f7910e79ae8 100644
@@ -403,6 +403,92 @@ static int aspeed_spi_chip_set_default_window(struct aspeed_spi_chip *chip)
 	return chip->ahb_window_size ? 0 : -1;
 }
 
+static int aspeed_spi_set_window(struct aspeed_spi *aspi,
+				 const struct aspeed_spi_window *win)
+{
+	u32 start = aspi->ahb_base_phy + win->offset;
+	u32 end = start + win->size;
+	void __iomem *seg_reg = aspi->regs + CE0_SEGMENT_ADDR_REG + win->cs * 4;
+	u32 seg_val_backup = readl(seg_reg);
+	u32 seg_val = aspi->data->segment_reg(aspi, start, end);
+
+	if (seg_val == seg_val_backup)
+		return 0;
+
+	writel(seg_val, seg_reg);
+
+	/*
+	 * Restore initial value if something goes wrong else we could
+	 * loose access to the chip.
+	 */
+	if (seg_val != readl(seg_reg)) {
+		dev_err(aspi->dev, "CE%d invalid window [ 0x%.8x - 0x%.8x ] %dMB",
+			win->cs, start, end - 1, win->size >> 20);
+		writel(seg_val_backup, seg_reg);
+		return -EIO;
+	}
+
+	if (win->size)
+		dev_dbg(aspi->dev, "CE%d new window [ 0x%.8x - 0x%.8x ] %dMB",
+			win->cs, start, end - 1,  win->size >> 20);
+	else
+		dev_dbg(aspi->dev, "CE%d window closed", win->cs);
+
+	return 0;
+}
+
+/*
+ * Yet to be done when possible :
+ * - Align mappings on flash size (we don't have the info)
+ * - ioremap each window, not strictly necessary since the overall window
+ *   is correct.
+ */
+static int aspeed_spi_chip_adjust_window(struct aspeed_spi_chip *chip,
+					 u32 local_offset, u32 size)
+{
+	struct aspeed_spi *aspi = chip->aspi;
+	struct aspeed_spi_window windows[ASPEED_SPI_MAX_NUM_CS] = { 0 };
+	struct aspeed_spi_window *win = &windows[chip->cs];
+	int ret;
+
+	aspeed_spi_get_windows(aspi, windows);
+
+	/* Adjust this chip window */
+	win->offset += local_offset;
+	win->size = size;
+
+	if (win->offset + win->size > aspi->ahb_window_size) {
+		win->size = aspi->ahb_window_size - win->offset;
+		dev_warn(aspi->dev, "CE%d window resized to %dMB", chip->cs, win->size >> 20);
+	}
+
+	ret = aspeed_spi_set_window(aspi, win);
+	if (ret)
+		return ret;
+
+	/* Update chip mapping info */
+	chip->ahb_base = aspi->ahb_base + win->offset;
+	chip->ahb_window_size = win->size;
+
+	/*
+	 * Also adjust next chip window to make sure that it does not
+	 * overlap with the current window.
+	 */
+	if (chip->cs < aspi->data->max_cs - 1) {
+		struct aspeed_spi_window *next = &windows[chip->cs + 1];
+
+		/* Change offset and size to keep the same end address */
+		if ((next->offset + next->size) > (win->offset + win->size))
+			next->size = (next->offset + next->size) - (win->offset + win->size);
+		else
+			next->size = 0;
+		next->offset = win->offset + win->size;
+
+		aspeed_spi_set_window(aspi, next);
+	}
+	return 0;
+}
+
 static int aspeed_spi_dirmap_create(struct spi_mem_dirmap_desc *desc)
 {
 	struct aspeed_spi *aspi = spi_controller_get_devdata(desc->mem->spi->master);
@@ -417,6 +503,8 @@ static int aspeed_spi_dirmap_create(struct spi_mem_dirmap_desc *desc)
 	if (op->data.dir != SPI_MEM_DATA_IN)
 		return -EOPNOTSUPP;
 
+	aspeed_spi_chip_adjust_window(chip, desc->info.offset, desc->info.length);
+
 	if (desc->info.length > chip->ahb_window_size)
 		dev_warn(aspi->dev, "CE%d window (%dMB) too small for mapping",
 			 chip->cs, chip->ahb_window_size >> 20);
Signature · 1 line
2.34.1
author maintainer
#7 lore raw

PATCH v3 7/11 spi: aspeed: Workaround AST2500 limitations

In reply to Cédric Le Goater

It is not possible to configure a full 128MB window for a chip of the same size on the AST2500 SPI controller. For this case, the maximum window size is restricted to 120MB for CE0.

---
 drivers/spi/spi-aspeed-smc.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/spi/spi-aspeed-smc.c +12 -0
index 9f7910e79ae8..ab6fa5cfad9c 100644
@@ -443,6 +443,8 @@ static int aspeed_spi_set_window(struct aspeed_spi *aspi,
  * - ioremap each window, not strictly necessary since the overall window
  *   is correct.
  */
+static const struct aspeed_spi_data ast2500_spi_data;
+
 static int aspeed_spi_chip_adjust_window(struct aspeed_spi_chip *chip,
 					 u32 local_offset, u32 size)
 {
@@ -451,6 +453,16 @@ static int aspeed_spi_chip_adjust_window(struct aspeed_spi_chip *chip,
 	struct aspeed_spi_window *win = &windows[chip->cs];
 	int ret;
 
+	/*
+	 * Due to an HW issue on the AST2500 SPI controller, the CE0
+	 * window size should be smaller than the maximum 128MB.
+	 */
+	if (aspi->data == &ast2500_spi_data && chip->cs == 0 && size == SZ_128M) {
+		size = 120 << 20;
+		dev_info(aspi->dev, "CE%d window resized to %dMB (AST2500 HW quirk)",
+			 chip->cs, size >> 20);
+	}
+
 	aspeed_spi_get_windows(aspi, windows);
 
 	/* Adjust this chip window */
Signature · 1 line
2.34.1
author maintainer
#8 lore raw

PATCH v3 8/11 spi: aspeed: Add support for the AST2400 SPI controller

In reply to Cédric Le Goater

Extend the driver for the AST2400 SPI Flash Controller (SPI). This controller has a slightly different interface which requires adaptation of the 4B handling. Summary of features :

. host Firmware
. 1 chip select pin (CE0)
. slightly different register set, between AST2500 and the legacy
controller
. no segment registers
. single, dual mode.

---
 drivers/spi/spi-aspeed-smc.c | 33 ++++++++++++++++++++++++++++++++-
 1 file changed, 32 insertions(+), 1 deletion(-)
drivers/spi/spi-aspeed-smc.c +32 -1
index ab6fa5cfad9c..7f306da7c44e 100644
@@ -30,6 +30,7 @@
 #define   CTRL_IO_DUAL_DATA		BIT(29)
 #define   CTRL_IO_QUAD_DATA		BIT(30)
 #define   CTRL_COMMAND_SHIFT		16
+#define   CTRL_IO_ADDRESS_4B		BIT(13)	/* AST2400 SPI only */
 #define   CTRL_IO_DUMMY_SET(dummy)					\
 	(((((dummy) >> 2) & 0x1) << 14) | (((dummy) & 0x3) << 6))
 #define   CTRL_CE_STOP_ACTIVE		BIT(2)
@@ -270,6 +271,8 @@ static bool aspeed_spi_supports_op(struct spi_mem *mem, const struct spi_mem_op
 	return spi_mem_default_supports_op(mem, op);
 }
 
+static const struct aspeed_spi_data ast2400_spi_data;
+
 static int do_aspeed_spi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
 {
 	struct aspeed_spi *aspi = spi_controller_get_devdata(mem->spi->master);
@@ -299,6 +302,9 @@ static int do_aspeed_spi_exec_op(struct spi_mem *mem, const struct spi_mem_op *o
 			addr_mode |= (0x11 << chip->cs);
 		else
 			addr_mode &= ~(0x11 << chip->cs);
+
+		if (op->addr.nbytes == 4 && chip->aspi->data == &ast2400_spi_data)
+			ctl_val |= CTRL_IO_ADDRESS_4B;
 	}
 
 	if (op->dummy.buswidth && op->dummy.nbytes)
@@ -390,7 +396,13 @@ static int aspeed_spi_chip_set_default_window(struct aspeed_spi_chip *chip)
 	struct aspeed_spi_window windows[ASPEED_SPI_MAX_NUM_CS] = { 0 };
 	struct aspeed_spi_window *win = &windows[chip->cs];
 
-	aspeed_spi_get_windows(aspi, windows);
+	/* No segment registers for the AST2400 SPI controller */
+	if (aspi->data == &ast2400_spi_data) {
+		win->offset = 0;
+		win->size = aspi->ahb_window_size;
+	} else {
+		aspeed_spi_get_windows(aspi, windows);
+	}
 
 	chip->ahb_base = aspi->ahb_base + win->offset;
 	chip->ahb_window_size = win->size;
@@ -453,6 +465,10 @@ static int aspeed_spi_chip_adjust_window(struct aspeed_spi_chip *chip,
 	struct aspeed_spi_window *win = &windows[chip->cs];
 	int ret;
 
+	/* No segment registers for the AST2400 SPI controller */
+	if (aspi->data == &ast2400_spi_data)
+		return 0;
+
 	/*
 	 * Due to an HW issue on the AST2500 SPI controller, the CE0
 	 * window size should be smaller than the maximum 128MB.
@@ -537,6 +553,12 @@ static int aspeed_spi_dirmap_create(struct spi_mem_dirmap_desc *desc)
 		else
 			addr_mode &= ~(0x11 << chip->cs);
 		writel(addr_mode, aspi->regs + CE_CTRL_REG);
+
+		/* AST2400 SPI controller sets 4BYTE address mode in
+		 * CE0 Control Register
+		 */
+		if (op->addr.nbytes == 4 && chip->aspi->data == &ast2400_spi_data)
+			ctl_val |= CTRL_IO_ADDRESS_4B;
 	}
 
 	/* READ mode is the controller default setting */
@@ -803,6 +825,14 @@ static const struct aspeed_spi_data ast2400_fmc_data = {
 	.segment_reg   = aspeed_spi_segment_reg,
 };
 
+static const struct aspeed_spi_data ast2400_spi_data = {
+	.max_cs	       = 1,
+	.hastype       = false,
+	.we0	       = 0,
+	.ctl0	       = 0x04,
+	/* No segment registers */
+};
+
 static const struct aspeed_spi_data ast2500_fmc_data = {
 	.max_cs	       = 3,
 	.hastype       = true,
@@ -847,6 +877,7 @@ static const struct aspeed_spi_data ast2600_spi_data = {
 
 static const struct of_device_id aspeed_spi_matches[] = {
 	{ .compatible = "aspeed,ast2400-fmc", .data = &ast2400_fmc_data },
+	{ .compatible = "aspeed,ast2400-spi", .data = &ast2400_spi_data },
 	{ .compatible = "aspeed,ast2500-fmc", .data = &ast2500_fmc_data },
 	{ .compatible = "aspeed,ast2500-spi", .data = &ast2500_spi_data },
 	{ .compatible = "aspeed,ast2600-fmc", .data = &ast2600_fmc_data },
Signature · 1 line
2.34.1
author maintainer
#9 lore raw

PATCH v3 9/11 spi: aspeed: Calibrate read timings

In reply to Cédric Le Goater

To accommodate the different response time of SPI transfers on different boards and different SPI NOR devices, the Aspeed controllers provide a set of Read Timing Compensation registers to tune the timing delays depending on the frequency being used. The AST2600 SoC has one of these registers per device. On the AST2500 and AST2400 SoCs, the timing register is shared by all devices which is problematic to get good results other than for one device.

The algorithm first reads a golden buffer at low speed and then performs reads with different clocks and delay cycle settings to find a breaking point. This selects a default good frequency for the CEx control register. The current settings are a bit optimistic as we pick the first delay giving good results. A safer approach would be to determine an interval and choose the middle value.

Calibration is performed when the direct mapping for reads is created. Since the underlying spi-nor object needs to be initialized to create the spi_mem operation for direct mapping, we should be fine. Having a specific API would clarify the requirements though.

---
 drivers/spi/spi-aspeed-smc.c | 281 +++++++++++++++++++++++++++++++++++
 1 file changed, 281 insertions(+)
drivers/spi/spi-aspeed-smc.c +281 -0
index 7f306da7c44e..660451667a39 100644
@@ -33,6 +33,8 @@
 #define   CTRL_IO_ADDRESS_4B		BIT(13)	/* AST2400 SPI only */
 #define   CTRL_IO_DUMMY_SET(dummy)					\
 	(((((dummy) >> 2) & 0x1) << 14) | (((dummy) & 0x3) << 6))
+#define   CTRL_FREQ_SEL_SHIFT		8
+#define   CTRL_FREQ_SEL_MASK		GENMASK(11, CTRL_FREQ_SEL_SHIFT)
 #define   CTRL_CE_STOP_ACTIVE		BIT(2)
 #define   CTRL_IO_MODE_CMD_MASK		GENMASK(1, 0)
 #define   CTRL_IO_MODE_NORMAL		0x0
@@ -45,6 +47,9 @@
 /* CEx Address Decoding Range Register */
 #define CE0_SEGMENT_ADDR_REG		0x30
 
+/* CEx Read timing compensation register */
+#define CE0_TIMING_COMPENSATION_REG	0x94
+
 enum aspeed_spi_ctl_reg_value {
 	ASPEED_SPI_BASE,
 	ASPEED_SPI_READ,
@@ -70,10 +75,15 @@ struct aspeed_spi_data {
 	bool	hastype;
 	u32	mode_bits;
 	u32	we0;
+	u32	timing;
+	u32	hclk_mask;
+	u32	hdiv_max;
 
 	u32 (*segment_start)(struct aspeed_spi *aspi, u32 reg);
 	u32 (*segment_end)(struct aspeed_spi *aspi, u32 reg);
 	u32 (*segment_reg)(struct aspeed_spi *aspi, u32 start, u32 end);
+	int (*calibrate)(struct aspeed_spi_chip *chip, u32 hdiv,
+			 const u8 *golden_buf, u8 *test_buf);
 };
 
 #define ASPEED_SPI_MAX_NUM_CS	5
@@ -517,6 +527,8 @@ static int aspeed_spi_chip_adjust_window(struct aspeed_spi_chip *chip,
 	return 0;
 }
 
+static int aspeed_spi_do_calibration(struct aspeed_spi_chip *chip);
+
 static int aspeed_spi_dirmap_create(struct spi_mem_dirmap_desc *desc)
 {
 	struct aspeed_spi *aspi = spi_controller_get_devdata(desc->mem->spi->master);
@@ -565,6 +577,8 @@ static int aspeed_spi_dirmap_create(struct spi_mem_dirmap_desc *desc)
 	chip->ctl_val[ASPEED_SPI_READ] = ctl_val;
 	writel(chip->ctl_val[ASPEED_SPI_READ], chip->ctl);
 
+	ret = aspeed_spi_do_calibration(chip);
+
 	dev_info(aspi->dev, "CE%d read buswidth:%d [0x%08x]\n",
 		 chip->cs, op->data.buswidth, chip->ctl_val[ASPEED_SPI_READ]);
 
@@ -812,6 +826,249 @@ static u32 aspeed_spi_segment_ast2600_reg(struct aspeed_spi *aspi,
 		((end - 1) & AST2600_SEG_ADDR_MASK);
 }
 
+/*
+ * Read timing compensation sequences
+ */
+
+#define CALIBRATE_BUF_SIZE SZ_16K
+
+static bool aspeed_spi_check_reads(struct aspeed_spi_chip *chip,
+				   const u8 *golden_buf, u8 *test_buf)
+{
+	int i;
+
+	for (i = 0; i < 10; i++) {
+		memcpy_fromio(test_buf, chip->ahb_base, CALIBRATE_BUF_SIZE);
+		if (memcmp(test_buf, golden_buf, CALIBRATE_BUF_SIZE) != 0) {
+#if defined(VERBOSE_DEBUG)
+			print_hex_dump_bytes(DEVICE_NAME "  fail: ", DUMP_PREFIX_NONE,
+					     test_buf, 0x100);
+#endif
+			return false;
+		}
+	}
+	return true;
+}
+
+#define FREAD_TPASS(i)	(((i) / 2) | (((i) & 1) ? 0 : 8))
+
+/*
+ * The timing register is shared by all devices. Only update for CE0.
+ */
+static int aspeed_spi_calibrate(struct aspeed_spi_chip *chip, u32 hdiv,
+				const u8 *golden_buf, u8 *test_buf)
+{
+	struct aspeed_spi *aspi = chip->aspi;
+	const struct aspeed_spi_data *data = aspi->data;
+	int i;
+	int good_pass = -1, pass_count = 0;
+	u32 shift = (hdiv - 1) << 2;
+	u32 mask = ~(0xfu << shift);
+	u32 fread_timing_val = 0;
+
+	/* Try HCLK delay 0..5, each one with/without delay and look for a
+	 * good pair.
+	 */
+	for (i = 0; i < 12; i++) {
+		bool pass;
+
+		if (chip->cs == 0) {
+			fread_timing_val &= mask;
+			fread_timing_val |= FREAD_TPASS(i) << shift;
+			writel(fread_timing_val, aspi->regs + data->timing);
+		}
+		pass = aspeed_spi_check_reads(chip, golden_buf, test_buf);
+		dev_dbg(aspi->dev,
+			"  * [%08x] %d HCLK delay, %dns DI delay : %s",
+			fread_timing_val, i / 2, (i & 1) ? 0 : 4,
+			pass ? "PASS" : "FAIL");
+		if (pass) {
+			pass_count++;
+			if (pass_count == 3) {
+				good_pass = i - 1;
+				break;
+			}
+		} else {
+			pass_count = 0;
+		}
+	}
+
+	/* No good setting for this frequency */
+	if (good_pass < 0)
+		return -1;
+
+	/* We have@least one pass of margin, let's use first pass */
+	if (chip->cs == 0) {
+		fread_timing_val &= mask;
+		fread_timing_val |= FREAD_TPASS(good_pass) << shift;
+		writel(fread_timing_val, aspi->regs + data->timing);
+	}
+	dev_dbg(aspi->dev, " * -> good is pass %d [0x%08x]",
+		good_pass, fread_timing_val);
+	return 0;
+}
+
+static bool aspeed_spi_check_calib_data(const u8 *test_buf, u32 size)
+{
+	const u32 *tb32 = (const u32 *)test_buf;
+	u32 i, cnt = 0;
+
+	/* We check if we have enough words that are neither all 0
+	 * nor all 1's so the calibration can be considered valid.
+	 *
+	 * I use an arbitrary threshold for now of 64
+	 */
+	size >>= 2;
+	for (i = 0; i < size; i++) {
+		if (tb32[i] != 0 && tb32[i] != 0xffffffff)
+			cnt++;
+	}
+	return cnt >= 64;
+}
+
+static const u32 aspeed_spi_hclk_divs[] = {
+	0xf, /* HCLK */
+	0x7, /* HCLK/2 */
+	0xe, /* HCLK/3 */
+	0x6, /* HCLK/4 */
+	0xd, /* HCLK/5 */
+};
+
+#define ASPEED_SPI_HCLK_DIV(i) \
+	(aspeed_spi_hclk_divs[(i) - 1] << CTRL_FREQ_SEL_SHIFT)
+
+static int aspeed_spi_do_calibration(struct aspeed_spi_chip *chip)
+{
+	struct aspeed_spi *aspi = chip->aspi;
+	const struct aspeed_spi_data *data = aspi->data;
+	u32 ahb_freq = aspi->clk_freq;
+	u32 max_freq = chip->clk_freq;
+	u32 ctl_val;
+	u8 *golden_buf = NULL;
+	u8 *test_buf = NULL;
+	int i, rc, best_div = -1;
+
+	dev_dbg(aspi->dev, "calculate timing compensation - AHB freq: %d MHz",
+		ahb_freq / 1000000);
+
+	/*
+	 * use the related low frequency to get check calibration data
+	 * and get golden data.
+	 */
+	ctl_val = chip->ctl_val[ASPEED_SPI_READ] & data->hclk_mask;
+	writel(ctl_val, chip->ctl);
+
+	test_buf = kzalloc(CALIBRATE_BUF_SIZE * 2, GFP_KERNEL);
+	if (!test_buf)
+		return -ENOMEM;
+
+	golden_buf = test_buf + CALIBRATE_BUF_SIZE;
+
+	memcpy_fromio(golden_buf, chip->ahb_base, CALIBRATE_BUF_SIZE);
+	if (!aspeed_spi_check_calib_data(golden_buf, CALIBRATE_BUF_SIZE)) {
+		dev_info(aspi->dev, "Calibration area too uniform, using low speed");
+		goto no_calib;
+	}
+
+#if defined(VERBOSE_DEBUG)
+	print_hex_dump_bytes(DEVICE_NAME "  good: ", DUMP_PREFIX_NONE,
+			     golden_buf, 0x100);
+#endif
+
+	/* Now we iterate the HCLK dividers until we find our breaking point */
+	for (i = ARRAY_SIZE(aspeed_spi_hclk_divs); i > data->hdiv_max - 1; i--) {
+		u32 tv, freq;
+
+		freq = ahb_freq / i;
+		if (freq > max_freq)
+			continue;
+
+		/* Set the timing */
+		tv = chip->ctl_val[ASPEED_SPI_READ] | ASPEED_SPI_HCLK_DIV(i);
+		writel(tv, chip->ctl);
+		dev_dbg(aspi->dev, "Trying HCLK/%d [%08x] ...", i, tv);
+		rc = data->calibrate(chip, i, golden_buf, test_buf);
+		if (rc == 0)
+			best_div = i;
+	}
+
+	/* Nothing found ? */
+	if (best_div < 0) {
+		dev_warn(aspi->dev, "No good frequency, using dumb slow");
+	} else {
+		dev_dbg(aspi->dev, "Found good read timings at HCLK/%d", best_div);
+
+		/* Record the freq */
+		for (i = 0; i < ASPEED_SPI_MAX; i++)
+			chip->ctl_val[i] = (chip->ctl_val[i] & data->hclk_mask) |
+				ASPEED_SPI_HCLK_DIV(best_div);
+	}
+
+no_calib:
+	writel(chip->ctl_val[ASPEED_SPI_READ], chip->ctl);
+	kfree(test_buf);
+	return 0;
+}
+
+#define TIMING_DELAY_DI		BIT(3)
+#define TIMING_DELAY_HCYCLE_MAX	5
+#define TIMING_REG_AST2600(chip)				\
+	((chip)->aspi->regs + (chip)->aspi->data->timing +	\
+	 (chip)->cs * 4)
+
+static int aspeed_spi_ast2600_calibrate(struct aspeed_spi_chip *chip, u32 hdiv,
+					const u8 *golden_buf, u8 *test_buf)
+{
+	struct aspeed_spi *aspi = chip->aspi;
+	int hcycle;
+	u32 shift = (hdiv - 2) << 3;
+	u32 mask = ~(0xfu << shift);
+	u32 fread_timing_val = 0;
+
+	for (hcycle = 0; hcycle <= TIMING_DELAY_HCYCLE_MAX; hcycle++) {
+		int delay_ns;
+		bool pass = false;
+
+		fread_timing_val &= mask;
+		fread_timing_val |= hcycle << shift;
+
+		/* no DI input delay first  */
+		writel(fread_timing_val, TIMING_REG_AST2600(chip));
+		pass = aspeed_spi_check_reads(chip, golden_buf, test_buf);
+		dev_dbg(aspi->dev,
+			"  * [%08x] %d HCLK delay, DI delay none : %s",
+			fread_timing_val, hcycle, pass ? "PASS" : "FAIL");
+		if (pass)
+			return 0;
+
+		/* Add DI input delays  */
+		fread_timing_val &= mask;
+		fread_timing_val |= (TIMING_DELAY_DI | hcycle) << shift;
+
+		for (delay_ns = 0; delay_ns < 0x10; delay_ns++) {
+			fread_timing_val &= ~(0xf << (4 + shift));
+			fread_timing_val |= delay_ns << (4 + shift);
+
+			writel(fread_timing_val, TIMING_REG_AST2600(chip));
+			pass = aspeed_spi_check_reads(chip, golden_buf, test_buf);
+			dev_dbg(aspi->dev,
+				"  * [%08x] %d HCLK delay, DI delay %d.%dns : %s",
+				fread_timing_val, hcycle, (delay_ns + 1) / 2,
+				(delay_ns + 1) & 1 ? 5 : 5, pass ? "PASS" : "FAIL");
+			/*
+			 * TODO: This is optimistic. We should look
+			 * for a working interval and save the middle
+			 * value in the read timing register.
+			 */
+			if (pass)
+				return 0;
+		}
+	}
+
+	/* No good setting for this frequency */
+	return -1;
+}
+
 /*
  * Platform definitions
  */
@@ -820,6 +1077,10 @@ static const struct aspeed_spi_data ast2400_fmc_data = {
 	.hastype       = true,
 	.we0	       = 16,
 	.ctl0	       = CE0_CTRL_REG,
+	.timing	       = CE0_TIMING_COMPENSATION_REG,
+	.hclk_mask     = 0xfffff0ff,
+	.hdiv_max      = 1,
+	.calibrate     = aspeed_spi_calibrate,
 	.segment_start = aspeed_spi_segment_start,
 	.segment_end   = aspeed_spi_segment_end,
 	.segment_reg   = aspeed_spi_segment_reg,
@@ -830,6 +1091,10 @@ static const struct aspeed_spi_data ast2400_spi_data = {
 	.hastype       = false,
 	.we0	       = 0,
 	.ctl0	       = 0x04,
+	.timing	       = 0x14,
+	.hclk_mask     = 0xfffff0ff,
+	.hdiv_max      = 1,
+	.calibrate     = aspeed_spi_calibrate,
 	/* No segment registers */
 };
 
@@ -838,6 +1103,10 @@ static const struct aspeed_spi_data ast2500_fmc_data = {
 	.hastype       = true,
 	.we0	       = 16,
 	.ctl0	       = CE0_CTRL_REG,
+	.timing	       = CE0_TIMING_COMPENSATION_REG,
+	.hclk_mask     = 0xfffff0ff,
+	.hdiv_max      = 1,
+	.calibrate     = aspeed_spi_calibrate,
 	.segment_start = aspeed_spi_segment_start,
 	.segment_end   = aspeed_spi_segment_end,
 	.segment_reg   = aspeed_spi_segment_reg,
@@ -848,6 +1117,10 @@ static const struct aspeed_spi_data ast2500_spi_data = {
 	.hastype       = false,
 	.we0	       = 16,
 	.ctl0	       = CE0_CTRL_REG,
+	.timing	       = CE0_TIMING_COMPENSATION_REG,
+	.hclk_mask     = 0xfffff0ff,
+	.hdiv_max      = 1,
+	.calibrate     = aspeed_spi_calibrate,
 	.segment_start = aspeed_spi_segment_start,
 	.segment_end   = aspeed_spi_segment_end,
 	.segment_reg   = aspeed_spi_segment_reg,
@@ -859,6 +1132,10 @@ static const struct aspeed_spi_data ast2600_fmc_data = {
 	.mode_bits     = SPI_RX_QUAD | SPI_RX_QUAD,
 	.we0	       = 16,
 	.ctl0	       = CE0_CTRL_REG,
+	.timing	       = CE0_TIMING_COMPENSATION_REG,
+	.hclk_mask     = 0xf0fff0ff,
+	.hdiv_max      = 2,
+	.calibrate     = aspeed_spi_ast2600_calibrate,
 	.segment_start = aspeed_spi_segment_ast2600_start,
 	.segment_end   = aspeed_spi_segment_ast2600_end,
 	.segment_reg   = aspeed_spi_segment_ast2600_reg,
@@ -870,6 +1147,10 @@ static const struct aspeed_spi_data ast2600_spi_data = {
 	.mode_bits     = SPI_RX_QUAD | SPI_RX_QUAD,
 	.we0	       = 16,
 	.ctl0	       = CE0_CTRL_REG,
+	.timing	       = CE0_TIMING_COMPENSATION_REG,
+	.hclk_mask     = 0xf0fff0ff,
+	.hdiv_max      = 2,
+	.calibrate     = aspeed_spi_ast2600_calibrate,
 	.segment_start = aspeed_spi_segment_ast2600_start,
 	.segment_end   = aspeed_spi_segment_ast2600_end,
 	.segment_reg   = aspeed_spi_segment_ast2600_reg,
Signature · 1 line
2.34.1
author maintainer
#10 lore raw

PATCH v3 10/11 ARM: dts: aspeed: Enable Dual SPI RX transfers

In reply to Cédric Le Goater

All these controllers support at least Dual SPI. Update the DTs.

---
 arch/arm/boot/dts/aspeed-g4.dtsi | 6 ++++++
 arch/arm/boot/dts/aspeed-g5.dtsi | 7 +++++++
 arch/arm/boot/dts/aspeed-g6.dtsi | 8 ++++++++
 3 files changed, 21 insertions(+)
arch/arm/boot/dts/aspeed-g4.dtsi +6 -0
index 9ae67e83cf60..31e6569db97e 100644
@@ -64,27 +64,32 @@ fmc: spi at 1e620000 {
 			flash at 0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
 				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash at 1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 3 {
 				reg = < 3 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 4 {
 				reg = < 4 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -100,6 +105,7 @@ flash at 0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
arch/arm/boot/dts/aspeed-g5.dtsi +7 -0
index c3e0a8e13c8a..29bf017899b6 100644
@@ -66,18 +66,21 @@ flash at 0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -93,12 +96,14 @@ flash at 0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -114,12 +119,14 @@ flash at 0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
arch/arm/boot/dts/aspeed-g6.dtsi +8 -0
index 1ad05dde19d2..ce93c56a21a7 100644
@@ -106,18 +106,21 @@ flash at 0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -133,12 +136,14 @@ flash at 0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -154,18 +159,21 @@ flash at 0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash at 2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
Signature · 1 line
2.34.1
author maintainer
#11 lore raw

PATCH v3 11/11 ARM: dts: aspeed-g4: Set spi-max-frequency for all flashes

In reply to Cédric Le Goater

From: Tao Ren <[email protected]>

Set "spi-max-frequency" to 50 MHz for all the flashes under the FMC controller to ensure the clock frequency is calculated correctly.

---
 arch/arm/boot/dts/aspeed-g4.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm/boot/dts/aspeed-g4.dtsi +4 -0
index 31e6569db97e..d3d919dcb8d4 100644
@@ -72,24 +72,28 @@ flash at 1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash at 2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash at 3 {
 				reg = < 3 >;
 				compatible = "jedec,spi-nor";
 				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash at 4 {
 				reg = < 4 >;
 				compatible = "jedec,spi-nor";
 				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 		};
Signature · 1 line
2.34.1