Skip to content

ARM: i.MX: nitrogen6x clean up

Stefano Babic u-boot 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest32 patches 0 repliesNew

Patches in v1 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/32nitrogen6x: implement board_cfb_skip() to disable text output+0 -00 replies
2/32nitrogen6x: simplify board_mmc_getcd+0 -00 replies
3/32nitrogen6x: configure SD2 pads for SDIO on USDHC2+0 -00 replies
4/32nitrogen6x: power-down miscellanous peripherals+0 -00 replies
5/32nitrogen6x: configure SGTL5000, CSI camera clock outputs+0 -00 replies
6/32nitrogen6x: staticize board file+0 -00 replies
7/32nitrogen6x: Allow U-Boot to be silent on UART2+0 -01 reply
8/32nitrogen6x: phy: add 100 us delay after phy reset+0 -00 replies
9/32nitrogen6x: prevent warnings about board_ehci* callbacks+0 -00 replies
10/32nitrogen6x: display: add support lvds jeida screen+0 -00 replies
11/32nitrogen6x: display: add qvga panel+0 -00 replies
12/32nitrogen6x: display: add support for LG-9.7 LVDS display+0 -00 replies
13/32nitrogen6x: display: add LDB-WXGA-S for SPWG 1280x800 displays+0 -00 replies
14/32nitrogen6x: display: add support for fusion 7 display+0 -00 replies
15/32nitrogen6x: display: add svga display (800x600)+0 -00 replies
16/32nitrogen6x: display: add Ampire 1024x600 panel+0 -00 replies
17/32nitrogen6x: display: add wvga-lvds panel+0 -00 replies
18/32nitrogen6x: display use I2C detect for HDMI+0 -00 replies
19/32nitrogen6x: config: add USB Mass Storage (ums) support+0 -00 replies
20/32nitrogen6x: config: allow boot to USB stick+0 -00 replies
21/32nitrogen6x: config: use FS_GENERIC load command+0 -00 replies
22/32nitrogen6x: config: add initrd_high+0 -00 replies
23/32nitrogen6x: config: expose SATA, then MMC over USB+0 -00 replies
24/32nitrogen6x: config: enable USB keyboard support+0 -00 replies
25/32nitrogen6x: config: add CONFIG_CMD_MEMTEST+0 -00 replies
26/32nitrogen6x: config: enable "i2c edid"+0 -00 replies
27/32nitrogen6x: config: allow more bootargs parameters+0 -00 replies
28/32nitrogen6x: config: disable logo+0 -00 replies
28/32nitrogen6x: config: disable logo+0 -00 replies
29/32nitrogen6x: config: configure usb_ether+0 -01 reply
29/32nitrogen6x: config: configure usb_ether+0 -01 reply
30/32nitrogen6x: config: add gpio command+0 -00 replies
31/32nitrogen6x: config: enable Android fastboot+0 -00 replies
32/32nitrogen6x: config: enable EXT4 filesystem+0 -00 replies

Reviews trailers per patch

2 of 34 patches have a Reviewed-by or Acked-by.

PatchStefano Babic
1/32
2/32
3/32
4/32
5/32
6/32
7/32
8/32
9/32
10/32
11/32
12/32
13/32
14/32
15/32
16/32
17/32
18/32
19/32
20/32
21/32
22/32
23/32
24/32
25/32
26/32
27/32
28/32A-b
28/32A-b
29/32
29/32
30/32
31/32
32/32

Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes.

Read the v1 thread

Cover letter [U-Boot] [PATCH 00/32] ARM: i.MX: nitrogen6x clean up

Hi Eric,

Quoted 6 lines · Eric Nelson

This collection of patches comprises a set of updates that have been lingering in our Github repository.

We're pushing them to main-line in preparation for the addition of a couple of boards that have also been lingering for a while.

Quoted 9 lines

Patches 1-9 are tweaks to the mx6qsabrelite/nitrogen6x initialization code.

Patches 10-18 add support for additional displays supported by the board(s) and tweak the HDMI detection.

Patches 19-32 enable and configure various features through changes to include/configs/nitrogen6x.h.

Patches are orthogonal and can be applied separetely. I have not seen any comments and I have not comments for most of them. I will start to apply the ones (most of them) are straightforward. Please wait until I end up with first pass - your next version will be much shorter !

Quoted 18 lines

Diego Rondini (1):
nitrogen6x: config: allow boot to USB stick

Eric Nelson (24):
nitrogen6x: implement board_cfb_skip() to disable text output
nitrogen6x: configure SD2 pads for SDIO on USDHC2
nitrogen6x: power-down miscellanous peripherals
nitrogen6x: staticize board file
nitrogen6x: Allow U-Boot to be silent on UART2
nitrogen6x: prevent warnings about board_ehci* callbacks
nitrogen6x: display: add qvga panel
nitrogen6x: display: add support for LG-9.7 LVDS display
nitrogen6x: display: add LDB-WXGA-S for SPWG 1280x800 displays
nitrogen6x: display: add support for fusion 7 display
nitrogen6x: display: add svga display (800x600)
nitrogen6x: display: add Ampire 1024x600 panel
nitrogen6x: display: add wvga-lvds panel
nitrogen6x: display use I2C detect for HDMI

Quoted 8 lines

nitrogen6x: config: add USB Mass Storage (ums) support
nitrogen6x: config: add initrd_high
nitrogen6x: config: expose SATA, then MMC over USB
nitrogen6x: config: enable USB keyboard support
nitrogen6x: config: add CONFIG_CMD_MEMTEST
nitrogen6x: config: enable "i2c edid"
nitrogen6x: config: disable logo
nitrogen6x: config: configure usb_ether

Mainly I have problems with fixed addresses - my comments to the related patch.

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

Read the cover letter in its thread