Skip to contentSkip to conversation

Problem implementing split access

LARTC Andy Hawthorn 1 participant 2 messages Jan 19, 2004 – Jan 20, 2004

lore
Share & tools
lore
#0 lore raw

Hello,

I am attempting to implement load balancing on a firewall to allow me to use two ISPs. I have followed the instructions in section 4.2 of the LARTC HOWTO but have got stuck on the split access section

I have the options CONFIG_IP_ADVANCED_ROUTER and CONFIG_IP_MULTIPLE_TABLES in my kernel (2.4.24) and have added routes to the /etc/iproute2/rt_tables file but when I try a command in the form of:

ip route add $P1_NET dev $IF1 src $IP1 table T1

such as:

    ip route add 192.168.10.0/24 dev eth0 src 192.168.10.250 table myisp

I get the error:

RTNETLINK answers: Invalid argument

This sounds like I have missed something that I need in the kernel but everything that was listed in the HOWTO has been included in my kernel. If I try the command without the src argument such as:

    ip route add 192.168.10.0/24 dev eth0 table myisp

..then I get no errors which would seem to sugest that the src argument is the problem here.

Any insight someone might have would be most apreciated!

Thanks,
Andy

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Hi,

----- Original Message -----
From: "Felipe Herrera" <[email protected]>
To: "Andy Hawthorn" <[email protected]>
Sent: Tuesday, January 20, 2004 9:13 AM
Subject: RE: [LARTC] Problem implementing split access

Quoted 5 lines

Hello Andy,

Quoted 3 lines

=== Original Message From Andy Hawthorn <[email protected]> ==> >Hello,

I am attempting to implement load balancing on a firewall to allow me to

use

Quoted 1 line
Quoted 1 line

two ISPs. I have followed the instructions in section 4.2 of the LARTC

HOWTO

Quoted 3 lines
Quoted 3 lines

but have got stuck on the split access section

I have the options CONFIG_IP_ADVANCED_ROUTER and

CONFIG_IP_MULTIPLE_TABLES

Quoted 1 line
Quoted 1 line

in my kernel (2.4.24) and have added routes to the

/etc/iproute2/rt_tables

Quoted 8 lines
Quoted 8 lines

file but when I try a command in the form of:

ip route add $P1_NET dev $IF1 src $IP1 table T1

such as:

ip route add 192.168.10.0/24 dev eth0 src 192.168.10.250 table myisp

Quoted 8 lines
Quoted 3 lines

I get the error:

RTNETLINK answers: Invalid argument

probe with:

    ip route add 192.168.10.0/24 dev eth0 src 192.168.10.250 proto static

/

Quoted 8 lines

table myisp

Good Luck;

Thanks for ths tip, but this still comes up with the same "RTNETLINK
answers: Invalid argument" eror that I got before. What should the proto argument actualy do?

Quoted 3 lines
Quoted 3 lines

This sounds like I have missed something that I need in the kernel but everything that was listed in the HOWTO has been included in my kernel.

If I

Quoted 12 lines
Quoted 12 lines

try the command without the src argument such as:

ip route add 192.168.10.0/24 dev eth0 table myisp

.then I get no errors which would seem to sugest that the src argument is the problem here.

Any insight someone might have would be most apreciated!

Thanks,
Andy

Quoted 7 lines
Quoted 3 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Felipe Herrera Martínez

Andy

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/