Skip to contentSkip to conversation

Can't enable dma on /dev/hda

DISCUSSION maxxle 3 participants 3 messages Feb 11, 2003 – Feb 12, 2003

lore
Share & tools
lore

maxxle

author
#0 lore raw

Hi!

I'm running a debian 3.0 System using kernel 2.4.19 (also tried 2.4.20). On this system it's not possible to enable dma on /dev/hda (HDD IDE)

The MoBo is a VIA Board called VIA-C3M266 (CLE266 chipset)
Northbridge: VT8623
Southbridge: VT8235

My kernel is compiled with this features:
ATAPI/IDE/MFM/RLL support --> IDE, ATA and ATAPI Block devices --> [*] generic PCI bus-master DMA support
[*] Use PCI DMA by default when available
[*] VIA82CXXX chipset support

And this is what hdparm tels me:
hdparm -d 1 /dev/hda:

/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)

What can I do to force my system to run using dma on /dev/hda. Or is my CLE266 chipset a bit too new for being supported by 2.4.19/20?

Hope somebody is able to help me

maxxle

#1 lore raw
Quoted 8 lines · maxxle

Hi!

I'm running a debian 3.0 System using kernel 2.4.19 (also tried 2.4.20). On this system it's not possible to enable dma on /dev/hda (HDD IDE)

The MoBo is a VIA Board called VIA-C3M266 (CLE266 chipset)
Northbridge: VT8623
Southbridge: VT8235

You need 2.4.21pre for the 8235

#2 lore raw
In reply to maxxle

I suppose that your chip is not supported by kernel. :-(

Kernel support only 82C*** chips... as you see, it's not your chip. i have VT82C598 bridge, and dma is available on my system.

Agri

---------- Original Message -----------
From: [email protected] (maxxle)
To: [email protected]
Sent: 11 Feb 2003 19:31:16 +0000
Subject: Can't enable dma on /dev/hda

Quoted 29 lines

Hi!

I'm running a debian 3.0 System using kernel 2.4.19 (also tried 2.4.20). On this system it's not possible to enable dma on /dev/hda (HDD IDE)

The MoBo is a VIA Board called VIA-C3M266 (CLE266 chipset)
Northbridge: VT8623
Southbridge: VT8235

My kernel is compiled with this features:
ATAPI/IDE/MFM/RLL support --> IDE, ATA and ATAPI Block devices --> [*] generic PCI bus-master DMA support
[*] Use PCI DMA by default when available
[*] VIA82CXXX chipset support

And this is what hdparm tels me:
hdparm -d 1 /dev/hda:

/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)

What can I do to force my system to run using dma on /dev/hda. Or is my CLE266 chipset a bit too new for being supported by 2.4.19/20?

Hope somebody is able to help me

Quoted 7 lines

maxxle

-
To unsubscribe from this list: send the line "unsubscribe linux- kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/

------- End of Original Message -------