Skip to contentSkip to conversation

hdc: lost interrupt ide-cd: cmd 0x3 timed out with 2.6.6-rc3-bk8

DISCUSSION Bob Gill 3 participants 3 messages May 6, 2004 – May 12, 2004

lore
Share & tools
lore

Bob Gill

author
#0 lore raw

Hi. I recently built 2.6.6-rc3-bk8. The boot process stalls with
ide-cd: cmd 0x5a timed out
hdc: lost interrupt.
hdc: lost interrupt.
hdc: lost interrupt.
hdc: lost interrupt.
ide-cd: cmd 0x3 timed out
...
There are no problems booting 2.6.6-rc3-bk6.
My system: FC2-test3.
When booting from 2.6.6-rc3-bk6, I get the following:
(from cat /proc/ioports)
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1080-109f : 0000:00:02.1
e000-e0ff : 0000:00:03.0
e000-e0ff : sis900
e400-e41f : 0000:00:09.0
e400-e41f : EMU10K1
e800-e807 : 0000:00:09.1
ec00-ec7f : 0000:00:0d.0
f000-f00f : 0000:00:02.5
f000-f007 : ide0
f008-f00f : ide1

from /proc/interrupts:
CPU0

  0:    1580849          XT-PIC  timer
  1:       4012          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  5:          6          XT-PIC  bttv0
  9:       9680          XT-PIC  acpi, EMU10K1, ohci1394
 10:     114470          XT-PIC  ohci_hcd, nvidia
 11:        562          XT-PIC  ohci_hcd, eth0
 12:      39542          XT-PIC  i8042
 14:      19181          XT-PIC  ide0
 15:      21677          XT-PIC  ide1
NMI:          0
LOC:    1580793
ERR:          0
MIS:          0

I didn't see anything in /Documentation. Besides running FC2-t3 (updated with yum), I have /sys and /udev (hotplug from 2004_04_01 and udev-025) installed. On my system /dev/hdc is a Sony DVD drive, and is not /boot or /.
I can still boot 2.6.6-rc3-bk6 without problems. Please email me for more information as I'm not on the list.
TIA,
Bob

#1 lore raw

zero IDE changes in bk6 -> bk8 but a lot of ACPI / IRQ related

Quoted 9 lines · Bob Gill

Hi. I recently built 2.6.6-rc3-bk8. The boot process stalls with
ide-cd: cmd 0x5a timed out
hdc: lost interrupt.
hdc: lost interrupt.
hdc: lost interrupt.
hdc: lost interrupt.
ide-cd: cmd 0x3 timed out
...
There are no problems booting 2.6.6-rc3-bk6.

#2 lore raw
In reply to Bob Gill
Quoted 7 lines · Bob Gill

Hi. I recently built 2.6.6-rc3-bk8. The boot process stalls with ide-cd: cmd 0x5a timed out
hdc: lost interrupt.
hdc: lost interrupt.
hdc: lost interrupt.
hdc: lost interrupt.
ide-cd: cmd 0x3 timed out
...

Same thing here with a SiS 962/963 and Linux 2.6.6. 2.6.5 was working just fine.
Also the acpi=noirq workaround works for me as well.

IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]

SiS 962/963 MuTIOL IDE UDMA133 controller