Skip to contentSkip to conversation

PCI->APIC IRQ transform -> 267 ?

DISCUSSION Robert Clark 2 participants 3 messages Oct 28, 2004 – Nov 2, 2004

lore
Share & tools
lore
#0 lore raw

I'm getting this with 2.4.27 (SMP):

PCI: Using IRQ router PIIX [8086/25a1] at 00:1f.0
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B2,I4,P0) -> 27
PCI->APIC IRQ transform: (B3,I4,P0) -> 267
PCI->APIC IRQ transform: (B3,I5,P0) -> 25
PCI->APIC IRQ transform: (B4,I4,P0) -> 267
PCI->APIC IRQ transform: (B4,I4,P1) -> 267
PCI->APIC IRQ transform: (B4,I6,P0) -> 26
PCI->APIC IRQ transform: (B4,I6,P1) -> 27
PCI->APIC IRQ transform: (B5,I9,P0) -> 17
PCI->APIC IRQ transform: (B5,I10,P0) -> 19

The devices which are being assigned 267 are Ethernet ports and return
error SIOCSIFFLAGS when I try and configure them with ifconfig. Devices (B4,I6,P0) & (B4,I6,P1) (also Ethernet ports) can be configured with ifconfig but don't receive any interrupts (according to /proc/interrupts) and don't work. Devices (B5,I10,P0) & (B3,I5,P0) (more Ethernet ports) work fine.

I've tried various combinations of ACPI, APIC & hyperthreading
disabled & enabled but without any luck and I've run out of ideas for debugging this. Can anyone help?

The board is a Supermicro P4SCT+II with a 3.2GHz P4 (with
hyperthreading). The devices which are being affected are both PCI-X Ethernet cards:

Intel PRO/1000MT 4-port Ethernet card (PCI-ID 8086:101D Rev 1)
Intel PRO/100S 2-port Ethernet card (PCI-ID 8086:1229 Rev D)

I've attached some dmesg info and an lspci -v.

Robert

#1 lore raw
Quoted 3 lines · Robert Clark

I'm getting this with 2.4.27 (SMP):

PCI: Using IRQ router PIIX [8086/25a1] at 00:1f.0

...

Quoted 1 line

PCI->APIC IRQ transform: (B3,I4,P0) -> 267

this is from pcibios_fixup_irqs() which is called only when ACPI is disabled. Let me know if you still have trouble with a kernel built with CONFIG_ACPI=y. Also, it would be good to know if other versions of the kernel are known to work, or if they all fail on this box.

thanks,
-Len

#2 lore raw
Quoted 4 lines · Len Brown
Quoted 2 lines · Robert Clark

I'm getting this with 2.4.27 (SMP):

Quoted 8 lines
Quoted 1 line

PCI: Using IRQ router PIIX [8086/25a1] at 00:1f.0

...

Quoted 1 line

PCI->APIC IRQ transform: (B3,I4,P0) -> 267

this is from pcibios_fixup_irqs() which is called only when ACPI is disabled. Let me know if you still have trouble with a kernel built with CONFIG_ACPI=y. Also, it would be good to know if other versions of the kernel are known to work, or if they all fail on this box.

Thanks - that sheds some light on things. I've had some success with
2.6.8 and thought it was a problem with the 2.4 series, but I've now recompiled 2.4.27 with CONFIG_ACPI and it does work.

Am I right in thinking that without CONFIG_ACPI, 2.4.27 simply trusts
the BIOS to set up ACPI? If so, I should talk to Supermicro as it sounds like it might be a BIOS problem.

Thanks,

Robert