remove dead entry in net wan Kconfig
PATCH 1/1 remove dead entry in net wan Kconfig
Remove dead entry from net wan Kconfig. This entry is left over from 2.4 where synclink used syncppp driver directly. synclink drivers now use generic HDLC
Signed-off-by Paul Fulghum <[email protected]>
drivers/net/wan/Kconfig +0 -12
@@ -134,18 +134,6 @@ The driver will be compiled as a module: the module will be called sealevel. -config SYNCLINK_SYNCPPP - tristate "SyncLink HDLC/SYNCPPP support" - depends on WAN - help - Enables HDLC/SYNCPPP support for the SyncLink WAN driver. - - Normally the SyncLink WAN driver works with the main PPP driver - <file:drivers/net/ppp_generic.c> and pppd program. - HDLC/SYNCPPP support allows use of the Cisco HDLC/PPP driver - <file:drivers/net/wan/syncppp.c>. The SyncLink WAN driver (in - character devices) must also be enabled. - # Generic HDLC config HDLC tristate "Generic HDLC layer"
Quoted 4 lines · Paul Fulghum
Remove dead entry from net wan
Kconfig. This entry is left over from 2.4 where synclink used syncppp driver directly. synclink drivers now use generic HDLC
What about also removing the entry for this option in the Makefile?
Quoted 13 lines
Signed-off-by Paul Fulghum <[email protected]>drivers/net/wan/Kconfig +0
-5@@ -134,18 +134,6 @@ The driver will be compiled as a module: the module will be called sealevel. -config SYNCLINK_SYNCPPP - tristate "SyncLink HDLC/SYNCPPP support" - depends on WAN - help - Enables HDLC/SYNCPPP support for the SyncLink WAN driver.
drivers/net/wan/Kconfig line 139
Quoted 10 lines
drivers/net/wan/Kconfig +0
-7- - Normally the SyncLink WAN driver works with the main PPP driver - <file:drivers/net/ppp_generic.c> and pppd program. - HDLC/SYNCPPP support allows use of the Cisco HDLC/PPP driver - <file:drivers/net/wan/syncppp.c>. The SyncLink WAN driver (in - character devices) must also be enabled. - # Generic HDLC config HDLC tristate "Generic HDLC layer"
cu
Adrian
Signature · 4 lines
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon SeedQuoted 1 line · Adrian Bunk
What about also removing the entry for this option in the
Makefile?
Good point, I'll do that.
Signature · 2 lines
Paul Fulghum Microgate Systems, Ltd.
PATCH 1/1 remove dead entry in net wan Makefile
Remove dead entry in net wan Makefile.
Entry is left over from 2.4 when synclink used syncppp. synclink drivers now use generic HDLC
Signed-off-by Paul Fulghum <[email protected]>
drivers/net/wan/Makefile +0 -1
@@ -36,7 +36,6 @@ obj-$(CONFIG_FARSYNC) += syncppp.o farsync.o obj-$(CONFIG_DSCC4) += dscc4.o obj-$(CONFIG_LANMEDIA) += syncppp.o -obj-$(CONFIG_SYNCLINK_SYNCPPP) += syncppp.o obj-$(CONFIG_X25_ASY) += x25_asy.o obj-$(CONFIG_LANMEDIA) += lmc/