Skip to contentSkip to conversation

OMAP3EVM: Set default bootfile

PATCH New Sanjeev Premi 5 participants 7 messages May 5, 2009 – May 12, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 OMAP3EVM: Set default bootfile

The current configuration doesn't define default
bootfile; leading to this warning at execution:

OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)

---
 include/configs/omap3_evm.h |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)
include/configs/omap3_evm.h +2 -0
index 549cef9..e205c01 100644
@@ -149,6 +149,8 @@
 /* Environment information */
 #define CONFIG_BOOTDELAY	10
 
+#define CONFIG_BOOTFILE		uImage
+
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x82000000\0" \
 	"console=ttyS2,115200n8\0" \
Signature · 1 line
1.6.2.2
#1 lore raw

PATCH 1/1 OMAP3EVM: Set default bootfile

Dear Sanjeev Premi,

Quoted 2 lines · In message <[email protected]> you wrote:

The current configuration doesn't define default
bootfile; leading to this warning at execution:

Note that this is not a problem, but a decision of the board maintainer.

Also, you can always just use setenv + saveenv if you want this changed on your board.

Quoted 11 lines

OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)

This is standard behaviour and not a problem.

Quoted 10 lines
---
 include/configs/omap3_evm.h |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)
include/configs/omap3_evm.h +0 -0
index 549cef9..e205c01 100644

include/configs/omap3_evm.h line 153

Quoted 5 lines
include/configs/omap3_evm.h +2 -0
@@ -149,6 +149,8 @@
 /* Environment information */
 #define CONFIG_BOOTDELAY	10
 
+#define CONFIG_BOOTFILE		uImage
+

You should probably add the board maintainer on Cc: (done here) to get his ACK.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The thing is, as you progress in the Craft,  you'll  learn  there  is
another rule... When you break rules, break 'em good and hard.
                                    - Terry Pratchett, _Wyrd Sisters_
#2 lore raw

PATCH 1/1 OMAP3EVM: Set default bootfile

Quoted 47 lines

-----Original Message-----
From: Wolfgang Denk [mailto:wd at denx.de]
Sent: Tuesday, May 05, 2009 3:51 PM
To: Premi, Sanjeev
Cc: u-boot at lists.denx.de; Pillai, Manikandan
Subject: Re: [U-Boot] [PATCH] OMAP3EVM: Set default bootfile

Dear Sanjeev Premi,

Quoted 2 lines · In message <[email protected]> you wrote:

The current configuration doesn't define default
bootfile; leading to this warning at execution:

Note that this is not a problem, but a decision of the board maintainer.

Also, you can always just use setenv + saveenv if you want this changed on your board.

Quoted 11 lines

OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)

This is standard behaviour and not a problem.

Review

Quoted 6 lines
---
 include/configs/omap3_evm.h |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)
(quoted diff) +0 -0

b/include/configs/omap3_evm.h

Quoted 7 lines

index 549cef9..e205c01 100644

include/configs/omap3_evm.h +0 -0
@@ -149,6 +149,8 @@
 /* Environment information */
 #define CONFIG_BOOTDELAY	10
 
Quoted 5 lines

include/configs/omap3_evm.h line 153

Quoted 2 lines
include/configs/omap3_evm.h +2 -0
+#define CONFIG_BOOTFILE		uImage
+

You should probably add the board maintainer on Cc: (done here) to get his ACK.

In this case, the board maintainer works with me. He will ACK it.

Quoted 14 lines

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The thing is, as you progress in the Craft,  you'll  learn  there  is
another rule... When you break rules, break 'em good and hard.
                                    - Terry Pratchett, _Wyrd Sisters_
#3 lore raw

PATCH 1/1 OMAP3EVM: Set default bootfile

In reply to Wolfgang Denk
Quoted 48 lines

-----Original Message-----
From: Wolfgang Denk [mailto:wd at denx.de]
Sent: Tuesday, May 05, 2009 3:51 PM
To: Premi, Sanjeev
Cc: u-boot at lists.denx.de; Pillai, Manikandan
Subject: Re: [U-Boot] [PATCH] OMAP3EVM: Set default bootfile

Dear Sanjeev Premi,

Quoted 2 lines · In message <[email protected]> you wrote:

The current configuration doesn't define default
bootfile; leading to this warning at execution:

Note that this is not a problem, but a decision of the board maintainer.

Also, you can always just use setenv + saveenv if you want this changed on your board.

Quoted 11 lines

OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)

This is standard behaviour and not a problem.

Quoted 13 lines
---
 include/configs/omap3_evm.h |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)
include/configs/omap3_evm.h +0 -0
index 549cef9..e205c01 100644
@@ -149,6 +149,8 @@
 /* Environment information */
 #define CONFIG_BOOTDELAY	10
 
Quoted 5 lines

include/configs/omap3_evm.h line 153

Quoted 2 lines
include/configs/omap3_evm.h +2 -0
+#define CONFIG_BOOTFILE		uImage
+

You should probably add the board maintainer on Cc: (done here) to get his ACK.

[Pillai, Manikandan]

Acked

Quoted 12 lines

Best regards,

Wolfgang Denk

--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The thing is, as you progress in the Craft, you'll learn there is another rule... When you break rules, break 'em good and hard.
- Terry Pratchett, _Wyrd Sisters_

#4 lore raw

PATCH 1/1 OMAP3EVM: Set default bootfile

In reply to Sanjeev Premi
Quoted 15 lines · Sanjeev Premi

The current configuration doesn't define default
bootfile; leading to this warning at execution:

OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)

Quoted 1 line
Quoted 17 lines
---
 include/configs/omap3_evm.h |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)
include/configs/omap3_evm.h +2 -0
index 549cef9..e205c01 100644
@@ -149,6 +149,8 @@
 /* Environment information */
 #define CONFIG_BOOTDELAY	10
 
+#define CONFIG_BOOTFILE		uImage
+
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x82000000\0" \
 	"console=ttyS2,115200n8\0" \
#5 lore raw

PATCH 1/1 OMAP3EVM: Set default bootfile

In reply to Sanjeev Premi
Quoted 14 lines · Sanjeev Premi

The current configuration doesn't define default
bootfile; leading to this warning at execution:

OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)

IMHO it's the correct way as you will be allow to have only one tftp server with one file per mac address

but as the Board Maintainer Ack it ok

as it's not really a fix but a preference it will be for the next expect you have a specific reason for this release

Best Regards,
J.

#6 lore raw

PATCH 1/1 OMAP3EVM: Set default bootfile

In reply to Sanjeev Premi
Quoted 15 lines · Sanjeev Premi

The current configuration doesn't define default
bootfile; leading to this warning at execution:

OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)

Quoted 2 lines

---

applied to arm/next

Best Regards,
J.