SAA7146-based card- tunes, but no multiplex
Hi all,
I have an (old) SAA7146-based DVB device- a Technotrend/Hauppauge WinTV DVB-S rev1.3 SE, if the autodetection is to be trusted. It is recognized without error (apparently), the firmware file resides in the appropriate folder and is loaded correctly, and nothing in the logs points to an error. However, while the device tunes and acquires a lock, no video data can be captured.
Here's what I think are the relevant messages from the kernel:
[ 19.620310] DVB: registering new adapter (Technotrend/Hauppauge WinTV DVB-S rev1.3 SE) [ 19.661939] adapter has MAC addr = 00:d0:5c:00:00:b3 [ 19.670459] dvb 0000:05:00.0: firmware: requesting av7110/bootcode.bin [ 19.906050] dvb-ttpci: gpioirq unknown type=0 len=0 [ 19.920105] dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 00000000, app 80002622 [ 19.920107] dvb-ttpci: firmware @ card 0 supports CI link layer interface [ 20.096224] dvb-ttpci: adac type set to 0 @ card 0 [ 20.101859] saa7146_vv: saa7146 (0): registered device video0 [v4l2] [ 20.101882] saa7146_vv: saa7146 (0): registered device vbi0 [v4l2] [ 20.289732] ves1x93: Detected ves1893a rev2 [ 20.289737] DVB: registering adapter 0 frontend 0 (VLSI VES1x93 DVB-S)... [ 20.289865] input: DVB on-card IR receiver as /devices/pci0000:00/0000:00:1e.0/0000:05:00.0/input/input6 [ 20.289900] dvb-ttpci: found av7110-0.
A tuning attempt using dvbtune yields:
Quoted 1 line
dvbtune -f 12551000 -p v -s 22000
Using DVB card "VLSI VES1x93 DVB-S"
tuning DVB-S to L-Band:134513994, Pol:V Srate=22000000, 22kHz=off polling....
Getting frontend eventFE_STATUS:
polling....
Getting frontend eventFE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
Event: Frequency: 12551859
SymbolRate: 22000000
FEC_inner: 5Bit error rate: 0
Signal strength: 43433
SNR: 57054FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
This is the output I get from 'scan' (dvbscan)
scanning /usr/share/dvb/dvb-s/Astra-19.2E
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 12551500 V 22000000 5
Quoted 1 line
Quoted 1 line
Quoted 1 line
tune to: 12551:v:0:22000
DVB-S IF freq is 1951500
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
dumping lists (0 services)
Done.
Using a different card, I can tune, scan using the same command and receive a TS, so reception problems can be ruled out.
Any suggestions how to proceed to resolve the issue or what further data to provide to that end would be highly appreciated.
Best regards
Dietmar
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb