Skip to contentSkip to conversation

Enable CPSW on TI814x EVM

PATCH Superseded Matt Porter 2 participants 11 messages Mar 15, 2013 – Mar 20, 2013 2 messages not in the archive

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover Enable CPSW on TI814x EVM

This series adds support for CPSW on the PG1.0 TI814x EVM board. The V1 CPSW on TI814x requires minor register changes to the existing driver as well as TI814x-specific pll/clock support. An ET1011C phy driver is added to support the PHY present on the PG1.0 EVM.

It has been tested loading/booting a Linux kernel and regression tested on BeagleBone and EVM-SK AM33XX boards. It has also been MAKEALL tested for all am33xx platforms.

The series applies on top of the following patches:

	- am33xx: Add required includes to some omap/am33xx code
	  http://patchwork.ozlabs.org/patch/227804/
	- Add TI814x EVM Support v4
	  http://www.mail-archive.com/u-boot at lists.denx.de/msg108356.html

Matt Porter (4):
am33xx: add pll and clock support for TI814x CPSW
cpsw: add support for TI814x slave_regs differences
phy: add support for ET1011C phys
ti814x_evm: enable CPSW support

 arch/arm/cpu/armv7/am33xx/clock_ti814x.c           |   56 +++++++++-
 arch/arm/include/asm/arch-am33xx/hardware_ti814x.h |    1 +
 board/ti/ti814x/evm.c                              |   75 +++++++++++++
 board/ti/ti814x/evm.h                              |    1 +
 board/ti/ti814x/mux.c                              |   35 +++++++
 drivers/net/cpsw.c                                 |    6 ++
 drivers/net/phy/Makefile                           |    1 +
 drivers/net/phy/et1011c.c                          |  110 ++++++++++++++++++++
 drivers/net/phy/phy.c                              |    3 +
 include/configs/ti814x_evm.h                       |   21 ++++
 include/phy.h                                      |    1 +
 11 files changed, 308 insertions(+), 2 deletions(-)
 create mode 100644 drivers/net/phy/et1011c.c
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH 1/4 am33xx: add pll and clock support for TI814x CPSW

Enables required PLLs and clocks for CPSW on TI814x.

---
 arch/arm/cpu/armv7/am33xx/clock_ti814x.c           |   56 +++++++++++++++++++-
 arch/arm/include/asm/arch-am33xx/hardware_ti814x.h |    1 +
 board/ti/ti814x/evm.c                              |    3 ++
 3 files changed, 58 insertions(+), 2 deletions(-)
arch/arm/cpu/armv7/am33xx/clock_ti814x.c +54 -2
index cb4210f..69ecf72 100644
@@ -183,7 +183,7 @@ struct cm_alwon {
 	unsigned int resv5[2];
 	unsigned int gpmcclkctrl;
 	unsigned int ethernet0clkctrl;
-	unsigned int resv6[1];
+	unsigned int ethernet1clkctrl;
 	unsigned int mpuclkctrl;
 	unsigned int debugssclkctrl;
 	unsigned int l3clkctrl;
@@ -203,9 +203,23 @@ struct cm_alwon {
 	unsigned int custefuseclkctrl;
 };
 
+#define SATA_PLL_BASE			(CTRL_BASE + 0x0720)
+
+struct sata_pll {
+	unsigned int pllcfg0;
+	unsigned int pllcfg1;
+	unsigned int pllcfg2;
+	unsigned int pllcfg3;
+	unsigned int pllcfg4;
+	unsigned int pllstatus;
+	unsigned int rxstatus;
+	unsigned int txstatus;
+	unsigned int testcfg;
+};
 
 const struct cm_alwon *cmalwon = (struct cm_alwon *)CM_ALWON_BASE;
 const struct cm_def *cmdef = (struct cm_def *)CM_DEFAULT_BASE;
+const struct sata_pll *spll = (struct sata_pll *)SATA_PLL_BASE;
 
 /*
  * Enable the peripheral clock for required peripherals
@@ -221,6 +235,18 @@ static void enable_per_clocks(void)
 	writel(PRCM_MOD_EN, &cmalwon->mmchs1clkctrl);
 	while (readl(&cmalwon->mmchs1clkctrl) != PRCM_MOD_EN)
 		;
+
+	/* Ethernet */
+	writel(PRCM_MOD_EN, &cmalwon->l3slowclkstctrl);
+	while ((readl(&cmalwon->l3slowclkstctrl) & 0x2100) != 0x2100)
+		;
+	writel(PRCM_MOD_EN, &cmalwon->ethclkstctrl);
+	writel(PRCM_MOD_EN, &cmalwon->ethernet0clkctrl);
+	while ((readl(&cmalwon->ethernet0clkctrl) & 0x30000) != 0)
+		;
+	writel(PRCM_MOD_EN, &cmalwon->ethernet1clkctrl);
+	while ((readl(&cmalwon->ethernet1clkctrl) & 0x30000) != 0)
+		;
 }
 
 /*
@@ -365,6 +391,31 @@ void ddr_pll_config(unsigned int ddrpll_m)
 	pll_config(DDR_PLL_BASE, DDR_N, DDR_M, DDR_M2, DDR_CLKCTRL, 1);
 }
 
+void sata_pll_config(void)
+{
+	/* TRM 21.3.1 */
+	writel(0xc12c003c, &spll->pllcfg1);
+	udelay(50);
+
+	writel(0x004008e0, &spll->pllcfg3);
+	udelay(50);
+
+	writel(0x80000004, &spll->pllcfg0);
+	udelay(50);
+
+	writel(0x80000014, &spll->pllcfg0);
+	udelay(50);
+
+	writel(0x80000016, &spll->pllcfg0);
+	udelay(50);
+
+	writel(0xc0000017, &spll->pllcfg0);
+	udelay(50);
+
+	while (((readl(&spll->pllstatus) & 0x01) == 0))
+		;
+}
+
 void enable_emif_clocks(void) {};
 
 void enable_dmm_clocks(void)
@@ -397,9 +448,10 @@ void pll_init()
 	/* Enable the control module */
 	writel(PRCM_MOD_EN, &cmalwon->controlclkctrl);
 
+	/* Configure PLLs */
 	mpu_pll_config();
-
 	l3_pll_config();
+	sata_pll_config();
 
 	/* Enable the required peripherals */
 	enable_per_clocks();
arch/arm/include/asm/arch-am33xx/hardware_ti814x.h +1 -0
index a950ac3..8f9315c 100644
@@ -29,6 +29,7 @@
 
 /* Control Module Base Address */
 #define CTRL_BASE			0x48140000
+#define CTRL_DEVICE_BASE		0x48140600
 
 /* PRCM Base Address */
 #define PRCM_BASE			0x48180000
board/ti/ti814x/evm.c +3 -0
index acc18fb..8513220 100644
@@ -151,6 +151,9 @@ void s_init(void)
 	 */
 	wdt_disable();
 
+	/* Enable timer */
+	timer_init();
+
 	/* Setup the PLLs and the clocks for the peripherals */
 	pll_init();
 
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH 1/4 am33xx: add pll and clock support for TI814x CPSW

On Fri, Mar 15, 2013 at 04:58:17PM -0400, Matt Porter wrote:

[snip]

arch/arm/cpu/armv7/am33xx/clock_ti814x.c static void enable_per_clocks(void) · line 248

Quoted 10 lines
arch/arm/cpu/armv7/am33xx/clock_ti814x.c +10 -0
+	/* Ethernet */
+	writel(PRCM_MOD_EN, &cmalwon->l3slowclkstctrl);
+	while ((readl(&cmalwon->l3slowclkstctrl) & 0x2100) != 0x2100)
+		;
+	writel(PRCM_MOD_EN, &cmalwon->ethclkstctrl);
+	writel(PRCM_MOD_EN, &cmalwon->ethernet0clkctrl);
+	while ((readl(&cmalwon->ethernet0clkctrl) & 0x30000) != 0)
+		;
+	writel(PRCM_MOD_EN, &cmalwon->ethernet1clkctrl);
+	while ((readl(&cmalwon->ethernet1clkctrl) & 0x30000) != 0)

Please define away the magic numbers.

[snip]

arch/arm/cpu/armv7/am33xx/clock_ti814x.c void ddr_pll_config(unsigned int ddrpll_m) · line 397

Quoted 4 lines
arch/arm/cpu/armv7/am33xx/clock_ti814x.c +4 -0
+void sata_pll_config(void)
+{
+	/* TRM 21.3.1 */
+	writel(0xc12c003c, &spll->pllcfg1);

I'm OK with comments, but please make it a multi-line thing that explains what's going on so that it's clear that yes, really, we shouldn't have defined these.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130315/ed782504/attachment.pgp>

A message that is not in the archive (sent off-list or not yet received): [email protected]

#4 lore raw

PATCH 1/4 am33xx: add pll and clock support for TI814x CPSW

Quoted 17 lines · Tom Rini

On Fri, Mar 15, 2013 at 04:58:17PM -0400, Matt Porter wrote:

[snip]

arch/arm/cpu/armv7/am33xx/clock_ti814x.c static void enable_per_clocks(void) · line 248

Quoted 10 lines
arch/arm/cpu/armv7/am33xx/clock_ti814x.c +10 -0
+	/* Ethernet */
+	writel(PRCM_MOD_EN, &cmalwon->l3slowclkstctrl);
+	while ((readl(&cmalwon->l3slowclkstctrl) & 0x2100) != 0x2100)
+		;
+	writel(PRCM_MOD_EN, &cmalwon->ethclkstctrl);
+	writel(PRCM_MOD_EN, &cmalwon->ethernet0clkctrl);
+	while ((readl(&cmalwon->ethernet0clkctrl) & 0x30000) != 0)
+		;
+	writel(PRCM_MOD_EN, &cmalwon->ethernet1clkctrl);
+	while ((readl(&cmalwon->ethernet1clkctrl) & 0x30000) != 0)

Please define away the magic numbers.

[snip]

Quoted 8 lines

arch/arm/cpu/armv7/am33xx/clock_ti814x.c void ddr_pll_config(unsigned int ddrpll_m) · line 397

Quoted 4 lines
arch/arm/cpu/armv7/am33xx/clock_ti814x.c +4 -0
+void sata_pll_config(void)
+{
+	/* TRM 21.3.1 */
+	writel(0xc12c003c, &spll->pllcfg1);

I'm OK with comments, but please make it a multi-line thing that explains what's going on so that it's clear that yes, really, we shouldn't have defined these.

I'll address this with gratuitous defines in v2...and expand the comment.

-Matt

#5 lore raw

PATCH 2/4 cpsw: add support for TI814x slave_regs differences

In reply to Matt Porter

TI814x's version 1 CPSW has a different slave_regs layout. Add support for the differing registers.

---
 drivers/net/cpsw.c |    6 ++++++
 1 file changed, 6 insertions(+)
drivers/net/cpsw.c +6 -0
index f5c5b9a..34c9fdd 100644
@@ -109,7 +109,13 @@ struct cpsw_slave_regs {
 	u32	flow_thresh;
 	u32	port_vlan;
 	u32	tx_pri_map;
+#ifdef CONFIG_AM33XX
 	u32	gap_thresh;
+#elif defined(CONFIG_TI814X)
+	u32	ts_ctl;
+	u32	ts_seq_ltype;
+	u32	ts_vlan;
+#endif
 	u32	sa_lo;
 	u32	sa_hi;
 };
Signature · 1 line
1.7.9.5
#6 lore raw

PATCH 2/4 cpsw: add support for TI814x slave_regs differences

Quoted 4 lines · Matt Porter

TI814x's version 1 CPSW has a different slave_regs layout. Add support for the differing registers.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130315/52950f00/attachment.pgp>
#7 lore raw

PATCH 3/4 phy: add support for ET1011C phys

In reply to Matt Porter

Adds an ET1011C PHY driver which is derived from the current Linux kernel PHY driver. Note that an errata workaround config option is implemented to allow for TX_CLK to be enabled even when gigabit mode is negotiated. This workaround is used on the TI814x-EVM.

---
 drivers/net/phy/Makefile  |    1 +
 drivers/net/phy/et1011c.c |  110 +++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy.c     |    3 ++
 include/phy.h             |    1 +
 4 files changed, 115 insertions(+)
 create mode 100644 drivers/net/phy/et1011c.c
drivers/net/phy/Makefile +1 -0
index 5e90d70..af5f4b8 100644
@@ -34,6 +34,7 @@ COBJS-$(CONFIG_PHYLIB_10G) += generic_10g.o
 COBJS-$(CONFIG_PHY_ATHEROS) += atheros.o
 COBJS-$(CONFIG_PHY_BROADCOM) += broadcom.o
 COBJS-$(CONFIG_PHY_DAVICOM) += davicom.o
+COBJS-$(CONFIG_PHY_ET1011C) += et1011c.o
 COBJS-$(CONFIG_PHY_LXT) += lxt.o
 COBJS-$(CONFIG_PHY_MARVELL) += marvell.o
 COBJS-$(CONFIG_PHY_MICREL) += micrel.o
drivers/net/phy/et1011c.c new file +110 -0

110 lines not on this page · raw message

drivers/net/phy/phy.c +3 -0
index d0ed766..f8c5481 100644
@@ -430,6 +430,9 @@ int phy_init(void)
 #ifdef CONFIG_PHY_DAVICOM
 	phy_davicom_init();
 #endif
+#ifdef CONFIG_PHY_ET1011C
+	phy_et1011c_init();
+#endif
 #ifdef CONFIG_PHY_LXT
 	phy_lxt_init();
 #endif
include/phy.h +1 -0
index 58ca273..7b4ce74 100644
@@ -223,6 +223,7 @@ int gen10g_discover_mmds(struct phy_device *phydev);
 int phy_atheros_init(void);
 int phy_broadcom_init(void);
 int phy_davicom_init(void);
+int phy_et1011c_init(void);
 int phy_lxt_init(void);
 int phy_marvell_init(void);
 int phy_micrel_init(void);
Signature · 1 line
1.7.9.5
#8 lore raw

PATCH 3/4 phy: add support for ET1011C phys

Quoted 6 lines · Matt Porter

Adds an ET1011C PHY driver which is derived from the current Linux kernel PHY driver. Note that an errata workaround config option is implemented to allow for TX_CLK to be enabled even when gigabit mode is negotiated. This workaround is used on the TI814x-EVM.

You need to specify the git hash or tag, not just "current".

The code itself is fine, so

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130315/de377a08/attachment.pgp>

A message that is not in the archive (sent off-list or not yet received): [email protected]

#10 lore raw

PATCH 3/4 phy: add support for ET1011C phys

Quoted 10 lines · Tom Rini
Quoted 6 lines · Matt Porter

Adds an ET1011C PHY driver which is derived from the current Linux kernel PHY driver. Note that an errata workaround config option is implemented to allow for TX_CLK to be enabled even when gigabit mode is negotiated. This workaround is used on the TI814x-EVM.

You need to specify the git hash or tag, not just "current".

Updated in v2

Quoted 3 lines

The code itself is fine, so

-Matt

#11 lore raw

PATCH 4/4 ti814x_evm: enable CPSW support

In reply to Matt Porter

Adds CPSW support to the TI814X EVM configured with an ET1011C PHY in GMII mode.

---
 board/ti/ti814x/evm.c        |   72 ++++++++++++++++++++++++++++++++++++++++++
 board/ti/ti814x/evm.h        |    1 +
 board/ti/ti814x/mux.c        |   35 ++++++++++++++++++++
 include/configs/ti814x_evm.h |   21 ++++++++++++
 4 files changed, 129 insertions(+)
board/ti/ti814x/evm.c +72 -0
index 8513220..d6c19f5 100644
@@ -17,6 +17,7 @@
  */
 
 #include <common.h>
+#include <cpsw.h>
 #include <errno.h>
 #include <spl.h>
 #include <asm/arch/cpu.h>
@@ -39,6 +40,8 @@ static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
 static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
 #endif
 
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
 /* UART Defines */
 #ifdef CONFIG_SPL_BUILD
 #define UART_RESET		(0x1 << 1)
@@ -166,6 +169,9 @@ void s_init(void)
 	/* Set MMC pins */
 	enable_mmc1_pin_mux();
 
+	/* Set Ethernet pins */
+	enable_enet_pin_mux();
+
 	/* Enable UART */
 	uart_enable();
 
@@ -199,3 +205,69 @@ int board_mmc_init(bd_t *bis)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x50,
+		.sliver_reg_ofs	= 0x700,
+		.phy_id		= 1,
+	},
+	{
+		.slave_reg_ofs	= 0x90,
+		.sliver_reg_ofs	= 0x740,
+		.phy_id		= 0,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x100,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0x600,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x28,
+	.hw_stats_reg_ofs	= 0x400,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_1,
+};
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+		printf("<ethaddr> not set. Reading from E-fuse\n");
+		/* try reading mac address from efuse */
+		mac_lo = readl(&cdev->macid0l);
+		mac_hi = readl(&cdev->macid0h);
+		mac_addr[0] = mac_hi & 0xFF;
+		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+		mac_addr[4] = mac_lo & 0xFF;
+		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+		else
+			printf("Unable to read MAC address. Set <ethaddr>\n");
+	}
+
+	return cpsw_register(&cpsw_data);
+}
board/ti/ti814x/evm.h +1 -0
index 40f8710..6aebec6 100644
@@ -3,5 +3,6 @@
 
 void enable_uart0_pin_mux(void);
 void enable_mmc1_pin_mux(void);
+void enable_enet_pin_mux(void);
 
 #endif /* _EVM_H */
board/ti/ti814x/mux.c +35 -0
index 137acb4..fd9f364 100644
@@ -40,6 +40,36 @@ static struct module_pin_mux mmc1_pin_mux[] = {
 	{-1},
 };
 
+static struct module_pin_mux enet_pin_mux[] = {
+	{OFFSET(pincntl232), MODE(0x01)},		/* EMAC_RMREFCLK */
+	{OFFSET(pincntl233), PULLUP_EN | MODE(0x01)},	/* MDCLK */
+	{OFFSET(pincntl234), PULLUP_EN | MODE(0x01)},	/* MDIO */
+	{OFFSET(pincntl235), MODE(0x01)},		/* EMAC[0]_MTCLK */
+	{OFFSET(pincntl236), MODE(0x01)},		/* EMAC[0]_MCOL */
+	{OFFSET(pincntl237), MODE(0x01)},		/* EMAC[0]_MCRS */
+	{OFFSET(pincntl238), MODE(0x01)},		/* EMAC[0]_MRXER */
+	{OFFSET(pincntl239), MODE(0x01)},		/* EMAC[0]_MRCLK */
+	{OFFSET(pincntl240), MODE(0x01)},		/* EMAC[0]_MRXD[0] */
+	{OFFSET(pincntl241), MODE(0x01)},		/* EMAC[0]_MRXD[1] */
+	{OFFSET(pincntl242), MODE(0x01)},		/* EMAC[0]_MRXD[2] */
+	{OFFSET(pincntl243), MODE(0x01)},		/* EMAC[0]_MRXD[3] */
+	{OFFSET(pincntl244), MODE(0x01)},		/* EMAC[0]_MRXD[4] */
+	{OFFSET(pincntl245), MODE(0x01)},		/* EMAC[0]_MRXD[5] */
+	{OFFSET(pincntl246), MODE(0x01)},		/* EMAC[0]_MRXD[6] */
+	{OFFSET(pincntl247), MODE(0x01)},		/* EMAC[0]_MRXD[7] */
+	{OFFSET(pincntl248), MODE(0x01)},		/* EMAC[0]_MRXDV */
+	{OFFSET(pincntl249), MODE(0x01)},		/* EMAC[0]_GMTCLK */
+	{OFFSET(pincntl250), MODE(0x01)},		/* EMAC[0]_MTXD[0] */
+	{OFFSET(pincntl251), MODE(0x01)},		/* EMAC[0]_MTXD[1] */
+	{OFFSET(pincntl252), MODE(0x01)},		/* EMAC[0]_MTXD[2] */
+	{OFFSET(pincntl253), MODE(0x01)},		/* EMAC[0]_MTXD[3] */
+	{OFFSET(pincntl254), MODE(0x01)},		/* EMAC[0]_MTXD[4] */
+	{OFFSET(pincntl255), MODE(0x01)},		/* EMAC[0]_MTXD[5] */
+	{OFFSET(pincntl256), MODE(0x01)},		/* EMAC[0]_MTXD[6] */
+	{OFFSET(pincntl257), MODE(0x01)},		/* EMAC[0]_MTXD[7] */
+	{OFFSET(pincntl258), MODE(0x01)},		/* EMAC[0]_MTXEN */
+};
+
 void enable_uart0_pin_mux(void)
 {
 	configure_module_pin_mux(uart0_pin_mux);
@@ -49,3 +79,8 @@ void enable_mmc1_pin_mux(void)
 {
 	configure_module_pin_mux(mmc1_pin_mux);
 }
+
+void enable_enet_pin_mux(void)
+{
+	configure_module_pin_mux(enet_pin_mux);
+}
include/configs/ti814x_evm.h +21 -0
index 4cbd789..ce0541a 100644
@@ -217,4 +217,25 @@
 /* Unsupported features */
 #undef CONFIG_USE_IRQ
 
+/* Ethernet */
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
+#define CONFIG_DRIVER_TI_CPSW
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT         10
+#define CONFIG_NET_MULTI
+#define CONFIG_PHY_GIGE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR			1
+#define CONFIG_PHY_ET1011C
+#define CONFIG_PHY_ET1011C_TX_CLK_FIX
+
 #endif	/* ! __CONFIG_TI814X_EVM_H */
Signature · 1 line
1.7.9.5
#12 lore raw

PATCH 4/4 ti814x_evm: enable CPSW support

Quoted 4 lines · Matt Porter

Adds CPSW support to the TI814X EVM configured with an ET1011C PHY in GMII mode.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130315/06d80497/attachment.pgp>