Skip to contentSkip to conversation

i8k patches

PATCH In review Pali Rohár 3 participants 14 messages Jan 12, 2015 Char and misc drivers

lore
Share & tools
lore
#0 lore raw

cover i8k patches

This patch series contains all i8k patches which were already sent to LKML and are not included in Greg's char-misc-testing branch yet (2015-01-12).

Guenter Roeck (2):
i8k: Rework error retries
i8k: Add support for Dell XPS 13

Pali Rohár (7):
i8k: Add support for temperature sensor labels
i8k: Register only temperature sensors which have labels
i8k: Return -ENODATA for invalid temperature
i8k: Make fan module parameters an unsigned
i8k: Autodetect fan RPM multiplier
i8k: Remove DMI config data for Latitude E6440 and E6540
i8k: Add support for fan labels

 drivers/char/i8k.c |  316 ++++++++++++++++++++++++++++++++++++----------------
 1 file changed, 217 insertions(+), 99 deletions(-)
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH 1/9 i8k: Add support for temperature sensor labels

This patch adds labels for temperature sensors if SMM function with EAX register 0x11a3 reports it. This information was taken from DOS binary NBSVC.MDM.

---
 drivers/char/i8k.c |   74 +++++++++++++++++++++++++++++++++++++++++++---------
 1 file changed, 61 insertions(+), 13 deletions(-)
drivers/char/i8k.c +61 -13
index e34a019..663868b 100644
@@ -42,6 +42,7 @@
 #define I8K_SMM_GET_FAN		0x00a3
 #define I8K_SMM_GET_SPEED	0x02a3
 #define I8K_SMM_GET_TEMP	0x10a3
+#define I8K_SMM_GET_TEMP_TYPE	0x11a3
 #define I8K_SMM_GET_DELL_SIG1	0xfea3
 #define I8K_SMM_GET_DELL_SIG2	0xffa3
 
@@ -288,6 +289,14 @@ static int i8k_set_fan(int fan, int speed)
 	return i8k_smm(&regs) ? : i8k_get_fan_status(fan);
 }
 
+static int i8k_get_temp_type(int sensor)
+{
+	struct smm_regs regs = { .eax = I8K_SMM_GET_TEMP_TYPE, };
+
+	regs.ebx = sensor & 0xff;
+	return i8k_smm(&regs) ? : regs.eax & 0xff;
+}
+
 /*
  * Read the cpu temperature.
  */
@@ -493,6 +502,29 @@ static int i8k_open_fs(struct inode *inode, struct file *file)
  * Hwmon interface
  */
 
+static ssize_t i8k_hwmon_show_temp_label(struct device *dev,
+					 struct device_attribute *devattr,
+					 char *buf)
+{
+	static const char * const labels[] = {
+		"CPU",
+		"GPU",
+		"SODIMM",
+		"Other",
+		"Ambient",
+		"Other",
+	};
+	int index = to_sensor_dev_attr(devattr)->index;
+	int type;
+
+	type = i8k_get_temp_type(index);
+	if (type < 0)
+		return type;
+	if (type >= ARRAY_SIZE(labels))
+		type = ARRAY_SIZE(labels) - 1;
+	return sprintf(buf, "%s\n", labels[type]);
+}
+
 static ssize_t i8k_hwmon_show_temp(struct device *dev,
 				   struct device_attribute *devattr,
 				   char *buf)
@@ -555,9 +587,17 @@ static ssize_t i8k_hwmon_set_pwm(struct device *dev,
 }
 
 static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, i8k_hwmon_show_temp, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp1_label, S_IRUGO, i8k_hwmon_show_temp_label, NULL,
+			  0);
 static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, i8k_hwmon_show_temp, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp2_label, S_IRUGO, i8k_hwmon_show_temp_label, NULL,
+			  1);
 static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, i8k_hwmon_show_temp, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp3_label, S_IRUGO, i8k_hwmon_show_temp_label, NULL,
+			  2);
 static SENSOR_DEVICE_ATTR(temp4_input, S_IRUGO, i8k_hwmon_show_temp, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp4_label, S_IRUGO, i8k_hwmon_show_temp_label, NULL,
+			  3);
 static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, i8k_hwmon_show_fan, NULL,
 			  I8K_FAN_LEFT);
 static SENSOR_DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, i8k_hwmon_show_pwm,
@@ -569,31 +609,39 @@ static SENSOR_DEVICE_ATTR(pwm2, S_IRUGO | S_IWUSR, i8k_hwmon_show_pwm,
 
 static struct attribute *i8k_attrs[] = {
 	&sensor_dev_attr_temp1_input.dev_attr.attr,	/* 0 */
-	&sensor_dev_attr_temp2_input.dev_attr.attr,	/* 1 */
-	&sensor_dev_attr_temp3_input.dev_attr.attr,	/* 2 */
-	&sensor_dev_attr_temp4_input.dev_attr.attr,	/* 3 */
-	&sensor_dev_attr_fan1_input.dev_attr.attr,	/* 4 */
-	&sensor_dev_attr_pwm1.dev_attr.attr,		/* 5 */
-	&sensor_dev_attr_fan2_input.dev_attr.attr,	/* 6 */
-	&sensor_dev_attr_pwm2.dev_attr.attr,		/* 7 */
+	&sensor_dev_attr_temp1_label.dev_attr.attr,	/* 1 */
+	&sensor_dev_attr_temp2_input.dev_attr.attr,	/* 2 */
+	&sensor_dev_attr_temp2_label.dev_attr.attr,	/* 3 */
+	&sensor_dev_attr_temp3_input.dev_attr.attr,	/* 4 */
+	&sensor_dev_attr_temp3_label.dev_attr.attr,	/* 5 */
+	&sensor_dev_attr_temp4_input.dev_attr.attr,	/* 6 */
+	&sensor_dev_attr_temp4_label.dev_attr.attr,	/* 7 */
+	&sensor_dev_attr_fan1_input.dev_attr.attr,	/* 8 */
+	&sensor_dev_attr_pwm1.dev_attr.attr,		/* 9 */
+	&sensor_dev_attr_fan2_input.dev_attr.attr,	/* 10 */
+	&sensor_dev_attr_pwm2.dev_attr.attr,		/* 11 */
 	NULL
 };
 
 static umode_t i8k_is_visible(struct kobject *kobj, struct attribute *attr,
 			      int index)
 {
-	if (index == 0 && !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP1))
+	if (index >= 0 && index <= 1 &&
+	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP1))
 		return 0;
-	if (index == 1 && !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP2))
+	if (index >= 2 && index <= 3 &&
+	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP2))
 		return 0;
-	if (index == 2 && !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP3))
+	if (index >= 4 && index <= 5 &&
+	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP3))
 		return 0;
-	if (index == 3 && !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP4))
+	if (index >= 6 && index <= 7 &&
+	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP4))
 		return 0;
-	if (index >= 4 && index <= 5 &&
+	if (index >= 8 && index <= 9 &&
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_FAN1))
 		return 0;
-	if (index >= 6 && index <= 7 &&
+	if (index >= 10 && index <= 11 &&
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_FAN2))
 		return 0;
 
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH 2/9 i8k: Register only temperature sensors which have labels

In reply to Pali Rohár

Detect presense of sensor by calling type function instead trying to read temperature value. Type function is working also for sensors which are temporary turned off (e.g on GPU which is turned off). Dell DOS binary NBSVC.MDM is doing similar checks, so we should do that too.

---
 drivers/char/i8k.c |   18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
drivers/char/i8k.c +9 -9
index 663868b..afcc9fe 100644
@@ -660,19 +660,19 @@ static int __init i8k_init_hwmon(void)
 
 	i8k_hwmon_flags = 0;
 
-	/* CPU temperature attributes, if temperature reading is OK */
-	err = i8k_get_temp(0);
-	if (err >= 0 || err == -ERANGE)
+	/* CPU temperature attributes, if temperature type is OK */
+	err = i8k_get_temp_type(0);
+	if (err >= 0)
 		i8k_hwmon_flags |= I8K_HWMON_HAVE_TEMP1;
 	/* check for additional temperature sensors */
-	err = i8k_get_temp(1);
-	if (err >= 0 || err == -ERANGE)
+	err = i8k_get_temp_type(1);
+	if (err >= 0)
 		i8k_hwmon_flags |= I8K_HWMON_HAVE_TEMP2;
-	err = i8k_get_temp(2);
-	if (err >= 0 || err == -ERANGE)
+	err = i8k_get_temp_type(2);
+	if (err >= 0)
 		i8k_hwmon_flags |= I8K_HWMON_HAVE_TEMP3;
-	err = i8k_get_temp(3);
-	if (err >= 0 || err == -ERANGE)
+	err = i8k_get_temp_type(3);
+	if (err >= 0)
 		i8k_hwmon_flags |= I8K_HWMON_HAVE_TEMP4;
 
 	/* Left fan attributes, if left fan is present */
Signature · 1 line
1.7.9.5
#3 lore raw

PATCH 3/9 i8k: Return -ENODATA for invalid temperature

In reply to Pali Rohár

Guenter Roeck suggested to return -ENODATA instead -ERANGE or -EINVAL when BIOS reports invalid temperature value.

---
 drivers/char/i8k.c |    4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
drivers/char/i8k.c +1 -3
index afcc9fe..1854fab 100644
@@ -331,7 +331,7 @@ static int i8k_get_temp(int sensor)
 		prev[sensor] = temp;
 	}
 	if (temp > I8K_MAX_TEMP)
-		return -ERANGE;
+		return -ENODATA;
 #endif
 
 	return temp;
@@ -533,8 +533,6 @@ static ssize_t i8k_hwmon_show_temp(struct device *dev,
 	int temp;
 
 	temp = i8k_get_temp(index);
-	if (temp == -ERANGE)
-		return -EINVAL;
 	if (temp < 0)
 		return temp;
 	return sprintf(buf, "%d\n", temp * 1000);
Signature · 1 line
1.7.9.5
#4 lore raw

PATCH 4/9 i8k: Rework error retries

In reply to Pali Rohár

From: Guenter Roeck <[email protected]>

Instead of returning a previous value if the SMM code returns an error when trying to read a temperature, retry once. If that fails again, return -ENODATA. Also return -ENODATA if an attempt is made to read the GPU temperature but the GPU is currently turned off.

Drop the I8K_TEMPERATURE_BUG definition and handle the related bug unconditionally.

---
 drivers/char/i8k.c |   47 ++++++++++++++++++++++++-----------------------
 1 file changed, 24 insertions(+), 23 deletions(-)
drivers/char/i8k.c +24 -23
index 1854fab..0e332fc 100644
@@ -5,7 +5,7 @@
  *
  * Hwmon integration:
  * Copyright (C) 2011  Jean Delvare <[email protected]>
- * Copyright (C) 2013  Guenter Roeck <[email protected]>
+ * Copyright (C) 2013, 2014  Guenter Roeck <[email protected]>
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -20,6 +20,7 @@
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
 
+#include <linux/delay.h>
 #include <linux/module.h>
 #include <linux/types.h>
 #include <linux/init.h>
@@ -59,8 +60,6 @@
 #define I8K_POWER_AC		0x05
 #define I8K_POWER_BATTERY	0x01
 
-#define I8K_TEMPERATURE_BUG	1
-
 static DEFINE_MUTEX(i8k_mutex);
 static char bios_version[4];
 static struct device *i8k_hwmon_dev;
@@ -300,39 +299,41 @@ static int i8k_get_temp_type(int sensor)
 /*
  * Read the cpu temperature.
  */
-static int i8k_get_temp(int sensor)
+static int _i8k_get_temp(int sensor)
 {
-	struct smm_regs regs = { .eax = I8K_SMM_GET_TEMP, };
-	int rc;
-	int temp;
+	struct smm_regs regs = {
+		.eax = I8K_SMM_GET_TEMP,
+		.ebx = sensor & 0xff,
+	};
 
-#ifdef I8K_TEMPERATURE_BUG
-	static int prev[4] = { I8K_MAX_TEMP+1, I8K_MAX_TEMP+1, I8K_MAX_TEMP+1, I8K_MAX_TEMP+1 };
-#endif
-	regs.ebx = sensor & 0xff;
-	rc = i8k_smm(&regs);
-	if (rc < 0)
-		return rc;
+	return i8k_smm(&regs) ? : regs.eax & 0xff;
+}
 
-	temp = regs.eax & 0xff;
+static int i8k_get_temp(int sensor)
+{
+	int temp = _i8k_get_temp(sensor);
 
-#ifdef I8K_TEMPERATURE_BUG
 	/*
 	 * Sometimes the temperature sensor returns 0x99, which is out of range.
-	 * In this case we return (once) the previous cached value. For example:
+	 * In this case we retry (once) before returning an error.
 	 # 1003655137 00000058 00005a4b
 	 # 1003655138 00000099 00003a80 <--- 0x99 = 153 degrees
 	 # 1003655139 00000054 00005c52
 	 */
-	if (temp > I8K_MAX_TEMP) {
-		temp = prev[sensor];
-		prev[sensor] = I8K_MAX_TEMP+1;
-	} else {
-		prev[sensor] = temp;
+	if (temp == 0x99) {
+		msleep(100);
+		temp = _i8k_get_temp(sensor);
 	}
+	/*
+	 * Return -ENODATA for all invalid temperatures.
+	 *
+	 * Known instances are the 0x99 value as seen above as well as
+	 * 0xc1 (193), which may be returned when trying to read the GPU
+	 * temperature if the system supports a GPU and it is currently
+	 * turned off.
+	 */
 	if (temp > I8K_MAX_TEMP)
 		return -ENODATA;
-#endif
 
 	return temp;
 }
Signature · 1 line
1.7.9.5
#5 lore raw

PATCH 5/9 i8k: Add support for Dell XPS 13

In reply to Pali Rohár

From: Guenter Roeck <[email protected]>

XPS 13 does not support turbo speed, so its initialization data matches that of XPS M140. Make XPS initialization data generic, and add support for XPS 13.

---
 drivers/char/i8k.c |   14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)
drivers/char/i8k.c +11 -3
index 0e332fc..8ec4c37 100644
@@ -705,7 +705,7 @@ enum i8k_configs {
 	DELL_LATITUDE_E6540,
 	DELL_PRECISION_490,
 	DELL_STUDIO,
-	DELL_XPS_M140,
+	DELL_XPS,
 };
 
 static const struct i8k_config_data i8k_config_data[] = {
@@ -725,7 +725,7 @@ static const struct i8k_config_data i8k_config_data[] = {
 		.fan_mult = 1,
 		.fan_max = I8K_FAN_HIGH,
 	},
-	[DELL_XPS_M140] = {
+	[DELL_XPS] = {
 		.fan_mult = 1,
 		.fan_max = I8K_FAN_HIGH,
 	},
@@ -837,12 +837,20 @@ static struct dmi_system_id i8k_dmi_table[] __initdata = {
 		.driver_data = (void *)&i8k_config_data[DELL_STUDIO],
 	},
 	{
+		.ident = "Dell XPS 13",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
+			DMI_MATCH(DMI_PRODUCT_NAME, "XPS13"),
+		},
+		.driver_data = (void *)&i8k_config_data[DELL_XPS],
+	},
+	{
 		.ident = "Dell XPS M140",
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
 			DMI_MATCH(DMI_PRODUCT_NAME, "MXC051"),
 		},
-		.driver_data = (void *)&i8k_config_data[DELL_XPS_M140],
+		.driver_data = (void *)&i8k_config_data[DELL_XPS],
 	},
 	{ }
 };
Signature · 1 line
1.7.9.5
#6 lore raw

PATCH 6/9 i8k: Make fan module parameters an unsigned

In reply to Pali Rohár

Setting negative fan multiplier or maximal fan speed does make any sense and can cause problems. So ensure that negative values will not be accepted.

---
 drivers/char/i8k.c |   18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
drivers/char/i8k.c +9 -9
index 8ec4c37..d6e8a26 100644
@@ -64,9 +64,9 @@ static DEFINE_MUTEX(i8k_mutex);
 static char bios_version[4];
 static struct device *i8k_hwmon_dev;
 static u32 i8k_hwmon_flags;
-static int i8k_fan_mult;
-static int i8k_pwm_mult;
-static int i8k_fan_max = I8K_FAN_HIGH;
+static uint i8k_fan_mult;
+static uint i8k_pwm_mult;
+static uint i8k_fan_max = I8K_FAN_HIGH;
 
 #define I8K_HWMON_HAVE_TEMP1	(1 << 0)
 #define I8K_HWMON_HAVE_TEMP2	(1 << 1)
@@ -95,12 +95,12 @@ static bool power_status;
 module_param(power_status, bool, 0600);
 MODULE_PARM_DESC(power_status, "Report power status in /proc/i8k");
 
-static int fan_mult = I8K_FAN_MULT;
-module_param(fan_mult, int, 0);
+static uint fan_mult = I8K_FAN_MULT;
+module_param(fan_mult, uint, 0);
 MODULE_PARM_DESC(fan_mult, "Factor to multiply fan speed with");
 
-static int fan_max = I8K_FAN_HIGH;
-module_param(fan_max, int, 0);
+static uint fan_max = I8K_FAN_HIGH;
+module_param(fan_max, uint, 0);
 MODULE_PARM_DESC(fan_max, "Maximum configurable fan speed");
 
 static int i8k_open_fs(struct inode *inode, struct file *file);
@@ -696,8 +696,8 @@ static int __init i8k_init_hwmon(void)
 }
 
 struct i8k_config_data {
-	int fan_mult;
-	int fan_max;
+	uint fan_mult;
+	uint fan_max;
 };
 
 enum i8k_configs {
Signature · 1 line
1.7.9.5
#7 lore raw

PATCH 7/9 i8k: Autodetect fan RPM multiplier

In reply to Pali Rohár

This patch adds new function i8k_get_fan_nominal_speed() for doing SMM call which will return nominal fan RPM for specified fan speed. It returns nominal RPM value at which fan operate when speed (0, 1, 2, 3) is set. It looks like RPM value is not accurate, but still provides very useful information.

New function i8k_get_fan_nominal_speed() is used for determinate if fan multiplier is 1 or 30. If function for maximal fan value success and returned RPM value too high (above 30000) then fan multiplier is set to 1. Otherwise multiplier is not changed and default value 30 is used.

---
 drivers/char/i8k.c |   60 +++++++++++++++++++++++++++++++++++++++++-----------
 1 file changed, 48 insertions(+), 12 deletions(-)
drivers/char/i8k.c +48 -12
index d6e8a26..6ad0872 100644
@@ -6,6 +6,7 @@
  * Hwmon integration:
  * Copyright (C) 2011  Jean Delvare <[email protected]>
  * Copyright (C) 2013, 2014  Guenter Roeck <[email protected]>
+ * Copyright (C) 2014  Pali Rohár <[email protected]>
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -42,12 +43,14 @@
 #define I8K_SMM_SET_FAN		0x01a3
 #define I8K_SMM_GET_FAN		0x00a3
 #define I8K_SMM_GET_SPEED	0x02a3
+#define I8K_SMM_GET_NOM_SPEED	0x04a3
 #define I8K_SMM_GET_TEMP	0x10a3
 #define I8K_SMM_GET_TEMP_TYPE	0x11a3
 #define I8K_SMM_GET_DELL_SIG1	0xfea3
 #define I8K_SMM_GET_DELL_SIG2	0xffa3
 
 #define I8K_FAN_MULT		30
+#define I8K_FAN_MAX_RPM		30000
 #define I8K_MAX_TEMP		127
 
 #define I8K_FN_NONE		0x00
@@ -64,7 +67,7 @@ static DEFINE_MUTEX(i8k_mutex);
 static char bios_version[4];
 static struct device *i8k_hwmon_dev;
 static u32 i8k_hwmon_flags;
-static uint i8k_fan_mult;
+static uint i8k_fan_mult = I8K_FAN_MULT;
 static uint i8k_pwm_mult;
 static uint i8k_fan_max = I8K_FAN_HIGH;
 
@@ -95,13 +98,13 @@ static bool power_status;
 module_param(power_status, bool, 0600);
 MODULE_PARM_DESC(power_status, "Report power status in /proc/i8k");
 
-static uint fan_mult = I8K_FAN_MULT;
+static uint fan_mult;
 module_param(fan_mult, uint, 0);
-MODULE_PARM_DESC(fan_mult, "Factor to multiply fan speed with");
+MODULE_PARM_DESC(fan_mult, "Factor to multiply fan speed with (default: autodetect)");
 
-static uint fan_max = I8K_FAN_HIGH;
+static uint fan_max;
 module_param(fan_max, uint, 0);
-MODULE_PARM_DESC(fan_max, "Maximum configurable fan speed");
+MODULE_PARM_DESC(fan_max, "Maximum configurable fan speed (default: autodetect)");
 
 static int i8k_open_fs(struct inode *inode, struct file *file);
 static long i8k_ioctl(struct file *, unsigned int, unsigned long);
@@ -276,6 +279,17 @@ static int i8k_get_fan_speed(int fan)
 }
 
 /*
+ * Read the fan nominal rpm for specific fan speed.
+ */
+static int i8k_get_fan_nominal_speed(int fan, int speed)
+{
+	struct smm_regs regs = { .eax = I8K_SMM_GET_NOM_SPEED, };
+
+	regs.ebx = (fan & 0xff) | (speed << 8);
+	return i8k_smm(&regs) ? : (regs.eax & 0xffff) * i8k_fan_mult;
+}
+
+/*
  * Set the fan speed (off, low, high). Returns the new fan status.
  */
 static int i8k_set_fan(int fan, int speed)
@@ -863,6 +877,7 @@ MODULE_DEVICE_TABLE(dmi, i8k_dmi_table);
 static int __init i8k_probe(void)
 {
 	const struct dmi_system_id *id;
+	int fan, ret;
 
 	/*
 	 * Get DMI information
@@ -891,19 +906,40 @@ static int __init i8k_probe(void)
 			return -ENODEV;
 	}
 
-	i8k_fan_mult = fan_mult;
-	i8k_fan_max = fan_max ? : I8K_FAN_HIGH;	/* Must not be 0 */
+	/*
+	 * Set fan multiplier and maximal fan speed from dmi config
+	 * Values specified in module parameters override values from dmi
+	 */
 	id = dmi_first_match(i8k_dmi_table);
 	if (id && id->driver_data) {
 		const struct i8k_config_data *conf = id->driver_data;
-
-		if (fan_mult == I8K_FAN_MULT && conf->fan_mult)
-			i8k_fan_mult = conf->fan_mult;
-		if (fan_max == I8K_FAN_HIGH && conf->fan_max)
-			i8k_fan_max = conf->fan_max;
+		if (!fan_mult && conf->fan_mult)
+			fan_mult = conf->fan_mult;
+		if (!fan_max && conf->fan_max)
+			fan_max = conf->fan_max;
 	}
+
+	i8k_fan_max = fan_max ? : I8K_FAN_HIGH;	/* Must not be 0 */
 	i8k_pwm_mult = DIV_ROUND_UP(255, i8k_fan_max);
 
+	if (!fan_mult) {
+		/*
+		 * Autodetect fan multiplier based on nominal rpm
+		 * If fan reports rpm value too high then set multiplier to 1
+		 */
+		for (fan = 0; fan < 2; ++fan) {
+			ret = i8k_get_fan_nominal_speed(fan, i8k_fan_max);
+			if (ret < 0)
+				continue;
+			if (ret > I8K_FAN_MAX_RPM)
+				i8k_fan_mult = 1;
+			break;
+		}
+	} else {
+		/* Fan multiplier was specified in module param or in dmi */
+		i8k_fan_mult = fan_mult;
+	}
+
 	return 0;
 }
 
Signature · 1 line
1.7.9.5
Reviewed-by on v1 7/9
#8 lore raw

Re: [PATCH 7/9] i8k: Autodetect fan RPM multiplier

Quoted 5 lines · Pali Rohár

This patch adds new function i8k_get_fan_nominal_speed() for doing SMM call which will return nominal fan RPM for specified fan speed. It returns nominal RPM value at which fan operate when speed (0, 1, 2, 3) is set. It looks like RPM value is not accurate, but still provides very useful information.

Quoted 8 lines

New function i8k_get_fan_nominal_speed() is used for determinate if fan multiplier is 1 or 30. If function for maximal fan value success and returned RPM value too high (above 30000) then fan multiplier is set to 1. Otherwise multiplier is not changed and default value 30 is used.

Greg,

with this the entire series is ready to go.

Thanks, and sorry for the long delay on my side.

Guenter

#9 lore raw

Re: [PATCH 7/9] i8k: Autodetect fan RPM multiplier

Quoted 15 lines · Guenter Roeck
Quoted 5 lines · Pali Rohár

This patch adds new function i8k_get_fan_nominal_speed() for doing SMM call which will return nominal fan RPM for specified fan speed. It returns nominal RPM value at which fan operate when speed (0, 1, 2, 3) is set. It looks like RPM value is not accurate, but still provides very useful information.

Quoted 8 lines

New function i8k_get_fan_nominal_speed() is used for determinate if fan multiplier is 1 or 30. If function for maximal fan value success and returned RPM value too high (above 30000) then fan multiplier is set to 1. Otherwise multiplier is not changed and default value 30 is used.

Quoted 5 lines

Greg,

with this the entire series is ready to go.

What about patch 9? It doesn't have your ack.

thanks,

greg k-h

#10 lore raw

Re: [PATCH 7/9] i8k: Autodetect fan RPM multiplier

Quoted 16 lines · Greg Kroah-Hartman
Quoted 15 lines · Guenter Roeck
Quoted 13 lines · Pali Rohár

This patch adds new function i8k_get_fan_nominal_speed() for doing SMM call which will return nominal fan RPM for specified fan speed. It returns nominal RPM value at which fan operate when speed (0, 1, 2, 3) is set. It looks like RPM value is not accurate, but still provides very useful information.

New function i8k_get_fan_nominal_speed() is used for determinate if fan multiplier is 1 or 30. If function for maximal fan value success and returned RPM value too high (above 30000) then fan multiplier is set to 1. Otherwise multiplier is not changed and default value 30 is used.

Quoted 8 lines
Quoted 5 lines

Greg,

with this the entire series is ready to go.

What about patch 9? It doesn't have your ack.

I thought I sent a Reviewed-by: for patch 9 prior to sending this mail. Must be getting old. I just re-sent it.

Guenter

#11 lore raw

PATCH 8/9 i8k: Remove DMI config data for Latitude E6440 and E6540

In reply to Pali Rohár

Both Dell Latitude machines were tested with new fan autodetection code and they are working fine. We already have DMI_MATCH data for generic Latitude machines which match also E6440 and E6540 models. So we do not need to maintain DMI data for those specific machines anymore.

---
 drivers/char/i8k.c |   21 ---------------------
 1 file changed, 21 deletions(-)
drivers/char/i8k.c +0 -21
index 6ad0872..09ebe06 100644
@@ -716,7 +716,6 @@ struct i8k_config_data {
 
 enum i8k_configs {
 	DELL_LATITUDE_D520,
-	DELL_LATITUDE_E6540,
 	DELL_PRECISION_490,
 	DELL_STUDIO,
 	DELL_XPS,
@@ -727,10 +726,6 @@ static const struct i8k_config_data i8k_config_data[] = {
 		.fan_mult = 1,
 		.fan_max = I8K_FAN_TURBO,
 	},
-	[DELL_LATITUDE_E6540] = {
-		.fan_mult = 1,
-		.fan_max = I8K_FAN_HIGH,
-	},
 	[DELL_PRECISION_490] = {
 		.fan_mult = 1,
 		.fan_max = I8K_FAN_TURBO,
@@ -776,22 +771,6 @@ static struct dmi_system_id i8k_dmi_table[] __initdata = {
 		.driver_data = (void *)&i8k_config_data[DELL_LATITUDE_D520],
 	},
 	{
-		.ident = "Dell Latitude E6440",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
-			DMI_MATCH(DMI_PRODUCT_NAME, "Latitude E6440"),
-		},
-		.driver_data = (void *)&i8k_config_data[DELL_LATITUDE_E6540],
-	},
-	{
-		.ident = "Dell Latitude E6540",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
-			DMI_MATCH(DMI_PRODUCT_NAME, "Latitude E6540"),
-		},
-		.driver_data = (void *)&i8k_config_data[DELL_LATITUDE_E6540],
-	},
-	{
 		.ident = "Dell Latitude 2",
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
Signature · 1 line
1.7.9.5
#12 lore raw

PATCH 9/9 i8k: Add support for fan labels

In reply to Pali Rohár

This patch adds labels support for fans if SMM function with EAX register 0x03a3 reports it. This information was taken from DOS binary NBSVC.MDM.

Additionally this patch change detection of fan presece. Instead reading fan status now detection is based on new label SMM function. Dell DOS binary NBSVC.MDM is doing similar checks, so we should do that too.

This patch also remove I8K_FAN_LEFT and I8K_FAN_RIGHT usage from hwmon driver part because that names does not make sense anymore. So numeric constants are used instead. Original /proc/i8k ioctl part was not changed for compatibility reasons.

---
 drivers/char/i8k.c |   76 ++++++++++++++++++++++++++++++++++++++++++----------
 1 file changed, 62 insertions(+), 14 deletions(-)
drivers/char/i8k.c +62 -14
index 09ebe06..24cc4ed 100644
@@ -43,6 +43,7 @@
 #define I8K_SMM_SET_FAN		0x01a3
 #define I8K_SMM_GET_FAN		0x00a3
 #define I8K_SMM_GET_SPEED	0x02a3
+#define I8K_SMM_GET_FAN_TYPE	0x03a3
 #define I8K_SMM_GET_NOM_SPEED	0x04a3
 #define I8K_SMM_GET_TEMP	0x10a3
 #define I8K_SMM_GET_TEMP_TYPE	0x11a3
@@ -279,6 +280,17 @@ static int i8k_get_fan_speed(int fan)
 }
 
 /*
+ * Read the fan type.
+ */
+static int i8k_get_fan_type(int fan)
+{
+	struct smm_regs regs = { .eax = I8K_SMM_GET_FAN_TYPE, };
+
+	regs.ebx = fan & 0xff;
+	return i8k_smm(&regs) ? : regs.eax & 0xff;
+}
+
+/*
  * Read the fan nominal rpm for specific fan speed.
  */
 static int i8k_get_fan_nominal_speed(int fan, int speed)
@@ -553,6 +565,37 @@ static ssize_t i8k_hwmon_show_temp(struct device *dev,
 	return sprintf(buf, "%d\n", temp * 1000);
 }
 
+static ssize_t i8k_hwmon_show_fan_label(struct device *dev,
+					struct device_attribute *devattr,
+					char *buf)
+{
+	static const char * const labels[] = {
+		"Processor Fan",
+		"Motherboard Fan",
+		"Video Fan",
+		"Power Supply Fan",
+		"Chipset Fan",
+		"Other Fan",
+	};
+	int index = to_sensor_dev_attr(devattr)->index;
+	bool dock = false;
+	int type;
+
+	type = i8k_get_fan_type(index);
+	if (type < 0)
+		return type;
+
+	if (type & 0x10) {
+		dock = true;
+		type &= 0x0F;
+	}
+
+	if (type >= ARRAY_SIZE(labels))
+		type = (ARRAY_SIZE(labels) - 1);
+
+	return sprintf(buf, "%s%s\n", (dock ? "Docking " : ""), labels[type]);
+}
+
 static ssize_t i8k_hwmon_show_fan(struct device *dev,
 				  struct device_attribute *devattr,
 				  char *buf)
@@ -611,14 +654,17 @@ static SENSOR_DEVICE_ATTR(temp3_label, S_IRUGO, i8k_hwmon_show_temp_label, NULL,
 static SENSOR_DEVICE_ATTR(temp4_input, S_IRUGO, i8k_hwmon_show_temp, NULL, 3);
 static SENSOR_DEVICE_ATTR(temp4_label, S_IRUGO, i8k_hwmon_show_temp_label, NULL,
 			  3);
-static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, i8k_hwmon_show_fan, NULL,
-			  I8K_FAN_LEFT);
+static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, i8k_hwmon_show_fan, NULL, 0);
+static SENSOR_DEVICE_ATTR(fan1_label, S_IRUGO, i8k_hwmon_show_fan_label, NULL,
+			  0);
 static SENSOR_DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, i8k_hwmon_show_pwm,
-			  i8k_hwmon_set_pwm, I8K_FAN_LEFT);
+			  i8k_hwmon_set_pwm, 0);
 static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, i8k_hwmon_show_fan, NULL,
-			  I8K_FAN_RIGHT);
+			  1);
+static SENSOR_DEVICE_ATTR(fan2_label, S_IRUGO, i8k_hwmon_show_fan_label, NULL,
+			  1);
 static SENSOR_DEVICE_ATTR(pwm2, S_IRUGO | S_IWUSR, i8k_hwmon_show_pwm,
-			  i8k_hwmon_set_pwm, I8K_FAN_RIGHT);
+			  i8k_hwmon_set_pwm, 1);
 
 static struct attribute *i8k_attrs[] = {
 	&sensor_dev_attr_temp1_input.dev_attr.attr,	/* 0 */
@@ -630,9 +676,11 @@ static struct attribute *i8k_attrs[] = {
 	&sensor_dev_attr_temp4_input.dev_attr.attr,	/* 6 */
 	&sensor_dev_attr_temp4_label.dev_attr.attr,	/* 7 */
 	&sensor_dev_attr_fan1_input.dev_attr.attr,	/* 8 */
-	&sensor_dev_attr_pwm1.dev_attr.attr,		/* 9 */
-	&sensor_dev_attr_fan2_input.dev_attr.attr,	/* 10 */
-	&sensor_dev_attr_pwm2.dev_attr.attr,		/* 11 */
+	&sensor_dev_attr_fan1_label.dev_attr.attr,	/* 9 */
+	&sensor_dev_attr_pwm1.dev_attr.attr,		/* 10 */
+	&sensor_dev_attr_fan2_input.dev_attr.attr,	/* 11 */
+	&sensor_dev_attr_fan2_label.dev_attr.attr,	/* 12 */
+	&sensor_dev_attr_pwm2.dev_attr.attr,		/* 13 */
 	NULL
 };
 
@@ -651,10 +699,10 @@ static umode_t i8k_is_visible(struct kobject *kobj, struct attribute *attr,
 	if (index >= 6 && index <= 7 &&
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_TEMP4))
 		return 0;
-	if (index >= 8 && index <= 9 &&
+	if (index >= 8 && index <= 10 &&
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_FAN1))
 		return 0;
-	if (index >= 10 && index <= 11 &&
+	if (index >= 11 && index <= 13 &&
 	    !(i8k_hwmon_flags & I8K_HWMON_HAVE_FAN2))
 		return 0;
 
@@ -688,13 +736,13 @@ static int __init i8k_init_hwmon(void)
 	if (err >= 0)
 		i8k_hwmon_flags |= I8K_HWMON_HAVE_TEMP4;
 
-	/* Left fan attributes, if left fan is present */
-	err = i8k_get_fan_status(I8K_FAN_LEFT);
+	/* First fan attributes, if fan type is OK */
+	err = i8k_get_fan_type(0);
 	if (err >= 0)
 		i8k_hwmon_flags |= I8K_HWMON_HAVE_FAN1;
 
-	/* Right fan attributes, if right fan is present */
-	err = i8k_get_fan_status(I8K_FAN_RIGHT);
+	/* Second fan attributes, if fan type is OK */
+	err = i8k_get_fan_type(1);
 	if (err >= 0)
 		i8k_hwmon_flags |= I8K_HWMON_HAVE_FAN2;
 
Signature · 1 line
1.7.9.5
Reviewed-by on v1 9/9
#13 lore raw

Re: [PATCH 9/9] i8k: Add support for fan labels

Quoted 7 lines · Pali Rohár

This patch adds labels support for fans if SMM function with EAX register 0x03a3 reports it. This information was taken from DOS binary NBSVC.MDM.

Additionally this patch change detection of fan presece. Instead reading fan status now detection is based on new label SMM function. Dell DOS binary NBSVC.MDM is doing similar checks, so we should do that too.

Quoted 6 lines

This patch also remove I8K_FAN_LEFT and I8K_FAN_RIGHT usage from hwmon driver part because that names does not make sense anymore. So numeric constants are used instead. Original /proc/i8k ioctl part was not changed for compatibility reasons.