Rockchip RV1108 eMMC initialization fail
Hi,
I am trying to use eMMC as a storage medium for my custom board based on Rockchip RV1108.
I have already made the changes as described in this thread:
http://u-boot.10912.n7.nabble.com/Rockchip-RV1108-eMMC-support-not-working-td343843.html#a343866
about using eMMC with RV1108.
When U-boot starts, and I try to access the eMMC, here is what I get:
=> mmc info
CMD_SEND:0
ARG 0x00000000
MMC_RSP_NONE
CMD_SEND:8
ARG 0x000001AA
RET -110
CMD_SEND:55
ARG 0x00000000
RET -110
CMD_SEND:0
ARG 0x00000000
MMC_RSP_NONE
CMD_SEND:1
ARG 0x00000000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:0
ARG 0x00000000
MMC_RSP_NONE
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0x003F8000
CMD_SEND:1
ARG 0x40300000
MMC_RSP_R3,4 0xC03F8000
CMD_SEND:2
ARG 0x00000000
MMC_RSP_R2 0x07FFFFFF
0xFFFFFFFF
0xFFFFFFFF
0xFFFFFFFF
DUMPING DATA
000 - 07 FF FF FF
004 - FF FF FF FF
008 - FF FF FF FF
012 - FF FF FF FF
CMD_SEND:3
ARG 0x00010000
RET -110So, as the last line says, I get Linux error code -110, which means "Connection timed out".
Here is info about the card I am using:
Flash Info:
Manufacturer: SAMSUNG,value=00
Flash Size: 7457MB
Block Size: 512KB
Page Size: 2KB
ECC Bits: 0
Access Time: 40
Flash CS: Flash<0>
I have also tried with different SD cards on Rockchip MINI EVB RV1108 board, but I get the same error.
I get the same error with U-boot from Rockchip, and mainline U-boot from Denx.
Any ideas?
Thanks,
Alex
--
Sent from: http://u-boot.10912.n7.nabble.com/
Hello,
Quoted 10 lines · On Mon, Nov 12, 2018 at 10:26 AM alex94 <[email protected]…
I am trying to use eMMC as a storage medium for my custom board based on Rockchip RV1108.
I have already made the changes as described in this thread:
http://u-boot.10912.n7.nabble.com/Rockchip-RV1108-eMMC-support-not-working-td343843.html#a343866
about using eMMC with RV1108.
When U-boot starts, and I try to access the eMMC, here is what I get:
Did you try my patchset to add it?
https://patchwork.ozlabs.org/project/uboot/list/?series=72834
Please give it a try.
Signature · 3 lines
Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9 9981-7854 Mobile: +1 (347) 903-9750
Quoted 14 lines · On 11/12/2018 10:23 AM, alex94 wrote:
Hi,
I am trying to use eMMC as a storage medium for my custom board based on Rockchip RV1108.I have already made the changes as described in this thread:
http://u-boot.10912.n7.nabble.com/Rockchip-RV1108-eMMC-support-not-working-td343843.html#a343866
about using eMMC with RV1108.
When U-boot starts, and I try to access the eMMC, here is what I get:
=> mmc info
CMD_SEND:0
Quoted 8 lines
ARG 0x00000000
MMC_RSP_NONE
CMD_SEND:8
ARG 0x000001AA
RET -110
CMD_SEND:55
ARG 0x00000000
RET -110How does the log look for an SD ? I suspect it's probably clock or pinmux that's broken.
Signature · 2 lines
Best regards, Marek Vasut
I tried it, but the same error still occurs :/
--
Sent from: http://u-boot.10912.n7.nabble.com/
The log for SD card is the same like the one I posted, when using mainline u-boot from Denx. When using u-boot from rockchip, the log is slightly different, but it is the same error. I will put that log here too as soon as I can.
--
Sent from: http://u-boot.10912.n7.nabble.com/
Quoted 4 lines · On 11/12/2018 04:25 PM, alex94 wrote:
The log for SD card is the same like the one I posted, when using mainline u-boot from Denx. When using u-boot from rockchip, the log is slightly different, but it is the same error. I will put that log here too as soon as I can.
Command 8 fails, which is the first command to which the card must respond. Thus, something is fundamentally wrong with the communication with the card.
Signature · 2 lines
Best regards, Marek Vasut
I should also mention that, I put U-boot itself into SD card/eMMC, so when I start the board, it gets loaded into RAM from SD card/eMMC. But after it loads and I can interact with it, I cannot communicate with the memory card(using the 'mmc' set of commands).
I have managed to find a workaround on Rockchip MINI EVB RV1108 board, putting the kernel image into USB, which I have access to, through the 'usb' commands. After the kernel starts, the SD card gets recognized by the kernel, and I can load the root filesystem from the SD card. So the problem is, after U-boot starts, I cannot use the SD card to load the kernel.
But on my custom board, I dont have USB, and I have to use the eMMC all the way through.
Also, here is the U-boot log when it starts, so under the MMC field, my eMMC gets recognized:
DDR Version V1.03 20180118
set vdd core 1.15v
In
600MHz
DDR3
Bus Width=16 Col=10 Bank=8 Row=13 CS=1 Die Bus-Width=16 Size=128MB mach:2
OUT
U-Boot 2018.11-rc3-00062-g26cc40d8c4-dirty (Nov 12 2018 - 11:43:08 +0100)
Model: Rockchip RV1108 Evaluation board
DRAM: 128 MiB
APLL: 600000000 DPLL:1200000000 GPLL:1188000000ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000
MMC: dwmmc at 30110000: 0 In: serial at 10210000 Out: serial at 10210000 Err: serial at 10210000 Model: Rockchip RV1108 Evaluation board Hit any key to stop autoboot: 0
=>
I appreciate a lot for the help till now,
Regards,
Alex
--
Sent from: http://u-boot.10912.n7.nabble.com/
Quoted 4 lines · On Mon, Nov 12, 2018 at 1:25 PM alex94 <[email protected]…
The log for SD card is the same like the one I posted, when using mainline u-boot from Denx. When using u-boot from rockchip, the log is slightly different, but it is the same error. I will put that log here too as soon as I can.
You might have PIN conflicts. Try to disable the SPI NOR and GMAC to start.
Signature · 3 lines
Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9 9981-7854 Mobile: +1 (347) 903-9750
I tried that, but the same error happens.
I saw that here in the first post:
http://u-boot.10912.n7.nabble.com/Rockchip-RV1108-eMMC-support-not-working-td343843.html#a343866
in the U-boot log, GPLL is 384000000, where in my log is 1188000000.
Also, in the same post from above, what kind of MMC card is used?
And here is the U-boot log, when I enable debug in include/common.h
just to put more information.
DDR Version V1.03 20180118
set vdd core 1.15v
In
600MHz
DDR3
Bus Width=16 Col=10 Bank=8 Row=13 CS=1 Die Bus-Width=16 Size=128MB mach:2
OUTuclass_find_device_by_seq: 0 -1uclass_find_device_by_seq: 0 0
- -1 -1 'root_driver'
- not founduclass_find_device_by_seq: 0 2
- 2 -1 'serial at 10210000'
- not foundofnode_read_u32: reg-offset: (not found)ofnode_read_u32: reg-shift: 0x2 (2)ofnode_read_u32: clock-frequency: 0x16e3600 (24000000)
U-Boot 2018.11-rc3-00069-g72b191da5a-dirty (Nov 13 2018 - 16:02:21 +0100)
Model: Rockchip RV1108 Evaluation board
DRAM: 128 MiBuclass_find_device_by_seq: 0 -1uclass_find_device_by_seq: 0 0
- -1 -1 'root_driver'
- not foundofnode_read_u32_array: ranges: ofnode_read_string: regulator-name:vcc5v0_otguclass_find_device_by_seq: 0 2
- 2 -1 'serial at 10210000'
- 1 -1 'serial at 10220000'
- 0 -1 'serial at 10230000'
- not founduclass_find_device_by_seq: 0 -1uclass_find_device_by_seq: 0 0
- -1 -1 'pinctrl'
- not founduclass_find_device_by_seq: 0 -1uclass_find_device_by_seq: 0 0
- -1 -1 'syscon at 10300000'
- -1 -1 'syscon at 20060000'
- -1 -1 'syscon at 202a0000'
- not foundofnode_read_u32_array: interrupts: ofnode_read_u32_array: interrupts:ofnode_read_u32_array: interrupts: ofnode_read_u32: reg-offset: (not found)ofnode_read_u32: reg-shift: 0x2 (2)uclass_find_device_by_seq: 0 -1uclass_find_device_by_seq: 0 0
- -1 -1 'oscillator'
- -1 -1 'clock-controller at 20200000'
- not foundofnode_read_u32_array: interrupts: APLL: 600000000 DPLL:1200000000 GPLL:1188000000ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000ofnode_read_u32: clock-frequency: 0x16e3600 (24000000)
MMC: uclass_find_device_by_seq: 0 0
- 0 -1 'dwmmc at 30110000'
- not founduclass_find_device_by_seq: 1 0
- 0 -1 'dwmmc at 30110000'
- founduclass_find_device_by_seq: 0 0
- 0 -1 'dwmmc at 30110000'
- not foundofnode_read_u32_array: interrupts: ofnode_read_u32: bus-width: 0x8 (8)ofnode_read_bool: non-removable: trueofnode_read_u32: fifo-depth: 0x100 (256)ofnode_read_bool: fifo-mode: falseofnode_read_u32_array: clock-freq-min-max: uclass_find_device_by_seq: 0 1
- 0 0 'dwmmc at 30110000'
- not founduclass_find_device_by_seq: 1 1
- 0 0 'dwmmc at 30110000'
- not found
dwmmc at 30110000: 0 In: serial at 10210000 Out: serial at 10210000 Err: serial at 10210000 Model: Rockchip RV1108 Evaluation board
=>
--
Sent from: http://u-boot.10912.n7.nabble.com/
Quoted 10 lines · On Tue, Nov 13, 2018 at 1:47 PM alex94 <[email protected]…
I tried that, but the same error happens.
I saw that here in the first post:
http://u-boot.10912.n7.nabble.com/Rockchip-RV1108-eMMC-support-not-working-td343843.html#a343866
in the U-boot log, GPLL is 384000000, where in my log is 1188000000.
Also, in the same post from above, what kind of MMC card is used?
Our board has a very minimal dts, we removed a lot of the nodes while adding support for it. Something like this: http://termbin.com/gqyd
Give this a go and see if it helps.
--
Otavio Salvador O.S. Systems
http://www.ossystems.com.br http://code.ossystems.com.br
Mobile: +55 (53) 9 9981-7854 Mobile: +1 (347) 903-9750