Skip to contentSkip to conversation

dt-bindings: mtd: brcmnand: Make nand-ecc-strength and nand-ecc-step-size optional

PATCH Applied Kamal Dasu 2 participants 3 messages May 21, 2019 – Jun 3, 2019

Subsystems (4)
lore
Share & tools
lore

Kamal Dasu

author
#0 lore raw

PATCH v3 1/2 dt-bindings: mtd: brcmnand: Make nand-ecc-strength and nand-ecc-step-size optional

nand-ecc-strength and nand-ecc-step-size can be made optional as brcmnand driver can support using raw NAND layer detected values.

---
 Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt +3 -3
index bcda1df..0d952af 100644
@@ -101,12 +101,12 @@ Required properties:
                               number (e.g., 0, 1, 2, etc.)
 - #address-cells            : see partition.txt
 - #size-cells               : see partition.txt
-- nand-ecc-strength         : see nand.txt
-- nand-ecc-step-size        : must be 512 or 1024. See nand.txt
 
 Optional properties:
+- nand-ecc-strength         : see nand-controller.yaml
+- nand-ecc-step-size        : must be 512 or 1024. See nand-controller.yaml
 - nand-on-flash-bbt         : boolean, to enable the on-flash BBT for this
-                              chip-select. See nand.txt
+                              chip-select. See nand-controller.yaml
 - brcm,nand-oob-sector-size : integer, to denote the spare area sector size
                               expected for the ECC layout in use. This size, in
                               addition to the strength and step-size,
Signature · 1 line
1.9.0.138.g2de3478
author
#1 lore raw

PATCH v3 2/2 mtd: nand: raw: brcmnand: fallback to detected ecc-strength, ecc-step-size

This change supports nand-ecc-step-size and nand-ecc-strength fields in brcmnand DT node to be optional.
see: Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt

If both nand-ecc-strength and nand-ecc-step-size are not specified in device tree node for NAND, raw NAND layer does detect ECC information by reading ONFI extended parameter page for parts using ONFI >= 2.1. In case of non-ONFI NAND parts there could be a nand_id table entry with ECC information. If there is valid device tree entry for nand-ecc-strength and nand-ecc-step-size fields it still shall override the detected values.

---
 drivers/mtd/nand/raw/brcmnand/brcmnand.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/mtd/nand/raw/brcmnand/brcmnand.c +11 -0
index ce0b8ff..1bdd490 100644
@@ -2144,6 +2144,17 @@ static int brcmnand_setup_dev(struct brcmnand_host *host)
 		return -EINVAL;
 	}
 
+	if (chip->ecc.mode != NAND_ECC_NONE &&
+	    (!chip->ecc.size || !chip->ecc.strength)) {
+		if (chip->base.eccreq.step_size && chip->base.eccreq.strength) {
+			/* use detected ECC parameters */
+			chip->ecc.size = chip->base.eccreq.step_size;
+			chip->ecc.strength = chip->base.eccreq.strength;
+			dev_info(ctrl->dev, "Using ECC step-size %d, strength %d\n",
+				chip->ecc.size, chip->ecc.strength);
+		}
+	}
+
 	switch (chip->ecc.size) {
 	case 512:
 		if (chip->ecc.algo == NAND_ECC_HAMMING)
Signature · 1 line
1.9.0.138.g2de3478