Skip to contentSkip to conversation

How can I build a 2.4 kernel on a 2.6 System

DISCUSSION [email protected] 2 participants 4 messages Oct 24, 2008 – Oct 26, 2008

lore
Share & tools
lore
#0 lore raw

Hello list

I will build some 2.4 kernel modules on a system with a running 2.6 kernel.

Is it possible and how can I do this?

Thanks for reply

#1 lore raw

Hi,

Quoted 5 lines · On Fri, Oct 24, 2008 at 02:16:40PM +0200, [email protected] wrote:

Hello list

I will build some 2.4 kernel modules on a system with a running 2.6 kernel.

Is it possible and how can I do this?

Not sure what you really mean. If you mean build 2.4 modules for 2.4 on a machine running 2.6, that's OK as there's no dependency between the running kernel and the one you're building. However, you should be careful about two things :
- gcc: it tends to be too recent for 2.4. gcc 4.1 is the highest version supported.
- modutils: most recent distros only ship module-init-tools without the old depmod. If you intend to "make modules_install INSTALL_MOD_PATH=..." then get prepared to see some errors from depmod at the end. The easiest solution consists in getting a depmod from an old machine an installing it in /tmp for instance.

Hoping this helps,
Willy

#2 lore raw

Hello Willy

Thanks for answering, but I have a problem with the compiling. When I try to compile the 2.4 kernel with the following commands:

# make clean && make mrproper
then I restore the .config file
# make oldconfig
# make dep && make bzImage respectively make modules

I get the following error message:

make[1]: Leaving directory `/fileserver/99_Frei/kernel-build-tree/linux-2.4.21-57.EL'
gcc -D__KERNEL__ -I/fileserver/99_Frei/kernel-build-tree/linux-2.4.21-57.EL/include -Wall -Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common
-Wno-unused -fomit-frame-pointer -pipe -freorder-blocks -march=i386 -DKBUILD_BASENAME=main
-c -o init/main.o init/main.c
init/main.c:1: Fehler: Die ausgewählte CPU unterstützt nicht den x86-64 Befehlssatz

English translation (by google)
init / main.c: 1: Error: The selected CPU does not support x86-64 instruction

I use a x86_64 system with a 2.6.16.60-0.31-smp kernel for compiling 2.4 kernel modules.

I think some compiler information are missing for make.

Could you help me?

----- Original Message ----- From: "Willy Tarreau" <[email protected]>
To: <[email protected]>
Cc: <[email protected]>
Sent: Friday, October 24, 2008 9:29 PM
Subject: Re: How can I build a 2.4 kernel on a 2.6 System

Quoted 32 lines

Hi,

Quoted 5 lines · On Fri, Oct 24, 2008 at 02:16:40PM +0200, [email protected] wrote:

Hello list

I will build some 2.4 kernel modules on a system with a running 2.6 kernel.

Is it possible and how can I do this?

Not sure what you really mean. If you mean build 2.4 modules for 2.4 on a machine running 2.6, that's OK as there's no dependency between the running kernel and the one you're building. However, you should be careful about two things :
- gcc: it tends to be too recent for 2.4. gcc 4.1 is the highest version supported.
- modutils: most recent distros only ship module-init-tools without the old depmod. If you intend to "make modules_install
INSTALL_MOD_PATH=..."
then get prepared to see some errors from depmod at the end. The
easiest
solution consists in getting a depmod from an old machine an installing it in /tmp for instance.

Hoping this helps,
Willy

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#3 lore raw
Quoted 11 lines · Jörg Dohle

Hello Willy

Thanks for answering, but I have a problem with the compiling. When I try to compile the 2.4 kernel with the following commands:

# make clean && make mrproper
then I restore the .config file
# make oldconfig
# make dep && make bzImage respectively make modules
Quoted 4 lines

I get the following error message:

make[1]: Leaving directory `/fileserver/99_Frei/kernel-build-tree/linux-2.4.21-57.EL'

OK, first it's an RHEL3 kernel, not a mainline one. The difference can sometimes be important.

Quoted 11 lines

gcc -D__KERNEL__

(quoted diff) +0 -2
-I/fileserver/99_Frei/kernel-build-tree/linux-2.4.21-57.EL/include -Wall 
-Wstrict-prototypes -Wno-trigraphs -O2 -fno-strict-aliasing -fno-common 
 -Wno-unused -fomit-frame-pointer -pipe -freorder-blocks  -march=i386   
 -DKBUILD_BASENAME=main -c -o init/main.o init/main.c

init/main.c:1: Fehler: Die ausgewählte CPU unterstützt nicht den x86-64 Befehlssatz

English translation (by google)
init / main.c: 1: Error: The selected CPU does not support x86-64 instruction

You might get native error messages by doing "export LANG=C" before building. I think that the problem you're encountering is simply because by default you're trying to build for a different architecture.

You should try appending "ARCH=i386" to all your make commands :

# make oldconfig ARCH=i386
# make dep ARCH=i386 && make bzImage ARCH=i386
# make modules ARCH=i386

It should theorically work, but since this is not used very often, it is possible that you still get minor trouble.

Regards,
Willy