Skip to contentSkip to conversation

cd-rom

parisc-linux Ulrich Strelow 1 participant 1 message Dec 29, 1999

lore
Share & tools
lore
#0 lore raw

Although I used HP-UX 9.x some years ago, I don't know what your mounting problem is. But anyway, in order to install HP-UX 10.20 you NEED to BOOT from the CD.

So please try to boot from the CD (e.g. press ESC during the boot sequence, search for bootable devices and select your CD hardware path 2.0.1.4.0). If you get any errors from this procedure, please post the error message(s) and the output from the search command.

Ulrich

-- "Soto, Gene G." <[email protected]>

Quoted 50 lines · wrote:

> I need to load 10.02 and am having problems
mounting a NEC
cdr-1410a cd-rom
> on my system (9000/712). Any advice on where to
go for help would
be
> appreciated. (SAM sees the device but I can't
mount it).

	> 
	> thanks

	Maybe a stupid question, but I have had similar

problems with a
floppy drive.
Have you tried to mount it "by hand"? I.e. not
using SAM, "mount
/dev/dsk/c0tXd0 /cdrom"
where X is the SCSI ID. There might (but probably
not) also be a
conflict
with the SCSI ID. Does "ioscan" see the device? Try
to boot from the
CD,
if that doesn't work then I don't know.

/Jan Bergman
[email protected] <mailto:[email protected]>

correction: it is a NEC MultiSpin 2Xe (CDR-74-1)

i have set the ID to 4. I also tried it on 3 and
it would not
detect it.

it has 4 switches on the back and i have 1 & 2 set
opposite of what
is recommended
on the NEC webpage for installation on IBM or
compatibles (that's
the only way SAM
detected the device):
switch 1 is Factory Use Only(Normal OFF) (I have it
ON)
switch 2 is Termination ON/OFF (I have it OFF) switch 3 is SCSI2/ON SCSI1/OFF (I have it OFF) switch 4 is Factory Use Only(Normal OFF) (I have it
ON)

Quoted 8 lines

I am running 9.01 (and don't have the 'n' option in
ioscan).
This is ioscan -f:

Class H/W Path Driver H/W Status S/W
Status

=====================================================

Quoted 57 lines
	graphics 1.0.0     graph3   ok(0x577)     ok       
 
	scsi     2.0.1     c700     ok(0x7071)    ok       
 
	disk     2.0.1.0.0 scsi     ok(0x202)     ok       
 
	disk     2.0.1.1.0 scsi     ok(0x202)     ok       
 
	disk     2.0.1.4.0 scsi     ok(0x5800100) ok       
 
	disk     2.0.1.5.0 scsi     ok(0x202)     ok       
 
	disk     2.0.1.6.0 scsi     ok(0x202)     ok       
 
	lan      2.0.2     lan01    ok(0x7072)    ok       
 
	hil      2.0.3     hil      ok(0x7073)    ok       
 
	serial   2.0.4     asio0    ok(0x7075)    ok       
 
	serial   2.0.5     asio0    ok(0x7075)    ok       
 
	parallel 2.0.6     parallel ok(0x7074)    ok       
 


	I get the following note from SAM when I try to add

the disk:
SAM was unable to determine the disk model of one
of the disk drives
on your system,
and is assuming that disk drive is used. This may
happen if the
disk drive is a
disk array or if the disk is not listed in
/usr/sam/lib/C/pd_devinfo.tx.

this is the only cd-rom info listed in
pd_devinfo.tx:

	DISK:::scsi::::TOSHIBA CD-ROM XM-3301TA:::SCSI
CD-ROM
drive::::::::::::::::CDROM_SCSI,
	DISK:::scsi::::TOSHIBA CD-ROM DRIVE:::::::SCSI

CD-ROM
drive::::::::::::::::CDROM_SCSI,

is it possible to add something to pd_devinfo.tx
that would allow it
to mount?

	these are the device files:
	/dev/dsk/4s0
	/dev/dsk/c201d4s0
	/dev/rdsk/4s0
	/dev/rdsk/c201d4s0

	when I try adding the following entry to
Quoted 7 lines

/etc/checklist:
/dev/dsk/c201d4s0 /cdrom cdfs defaults

i get the following message when i try to mount it:
/dev/dsk/c201d4s0: Device busy

---------------------------------------------------------------------------

Quoted 5 lines

To unsubscribe: send e-mail to
[email protected] with
`unsubscribe' as the subject.

__________________________________________________
Do You Yahoo!?
Talk to your friends online with Yahoo! Messenger.
http://messenger.yahoo.com