Skip to contentSkip to conversation

I am looking for a mips machine

DISCUSSION H . J . Lu 8 participants 12 messages Oct 24, 2001 – Oct 25, 2001 MIPS

lore
Share & tools
lore

H . J . Lu

author
#0 lore raw

Hi,

I am looking for a mips machine to continue working on my mips port of RedHat. My requirements are

1. It has the stable, up to date kernel support. That means I can do

# ./configure
# make bootstrap
# make check

for gcc 3.1 without a kernel oops.

2. It has decent CPU. I hate to wait a day for

# make bootstrap

3. Inexpensive.

4. Support serial console.

5. Little endian is preferred.

Does anyone have any recommendations?

Thanks.

H.J.

#1 lore raw
Quoted 16 lines

I am looking for a mips machine to continue working on my mips port of RedHat. My requirements are

1. It has the stable, up to date kernel support. That means I can do

# ./configure
# make bootstrap
# make check

for gcc 3.1 without a kernel oops.

2. It has decent CPU. I hate to wait a day for

# make bootstrap
Quoted 7 lines

3. Inexpensive.

4. Support serial console.

5. Little endian is preferred.

Does anyone have any recommendations?

I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.

author
#2 lore raw
Quoted 3 lines · James Simmons

I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.

I think Cobalt Qube is slow and is hard to expand the memory. I need at least 128MB RAM. Also the current mips kernel doesn't support it.

H.J.

#3 lore raw
Quoted 5 lines
Quoted 3 lines

I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.

I think Cobalt Qube is slow and is hard to expand the memory.

Slow that it is. As for memory it has two banks for 72 pin memory. I want to add memory to the Qube I have.

Quoted 1 line

Also the current mips kernel doesn't support it.

In the CVS tree I have it works and this tree is against Ralph's tree.

author
#4 lore raw
Quoted 8 lines · James Simmons
Quoted 5 lines
Quoted 3 lines

I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.

I think Cobalt Qube is slow and is hard to expand the memory.

Slow that it is. As for memory it has two banks for 72 pin memory. I want to add memory to the Qube I have.

I have access to a Raq 2. But it won't take my old EDO SIMMs :-). Besides, it only supports an 2.2 kernel.

H.J.

#5 lore raw
Quoted 2 lines

I have access to a Raq 2. But it won't take my old EDO SIMMs :-).

That sucks. Have you have any luck with any memory chips?

Quoted 1 line

Besides, it only supports an 2.2 kernel.

jsimmons@borgcube:~$ cat /proc/cpuinfo
cpu                     : MIPS
cpu model               : Nevada V10.0
system type             : Cobalt Microserver 27
BogoMIPS                : 249.85
byteorder               : little endian
unaligned accesses      : 0
wait instruction        : yes
microsecond timers      : yes
extra interrupt vector  : yes
hardware watchpoint     : no
VCED exceptions         : not available
VCEI exceptions         : not available
jsimmons@borgcube:~$ uname -nr
borgcube 2.4.10-mips
jsimmons@borgcube:~$

Actually I need to migrate the code to the new time and pci code. I will be sending a diff to Ralph in the next few days.

#6 lore raw
In reply to H . J . Lu

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 2 lines

I have access to a Raq 2. But it won't take my old EDO SIMMs :-). Besides, it only supports an 2.2 kernel.

well, nog exactly:

I've got a Raq 2 running 2.4.7-pre6 + pty-support here, running for 79 days now...
don't know exacty which patches i used, but i think i can figure it out, if you like...
at least one of the patches is named 'linux-2.4.7-pre6-mips-cobalt-v1.patch' ;))

it's currently used as a simpel web-server for development/test stuff.

i could supply more info if you like that....

Cheers,
Taco.

- ---
"One World, one Web, one Program" - Microsoft promo ad "Ein Volk, ein Reich, ein Fuhrer" - Adolf Hitler
- ---
GPG KeyID=0x9DD13814
GPG Fingerprint=7DF2 0E97 C5B9 6945 BD0B 3C9F E969 7018 9DD1 3814 GPG Key: http://www.taco.dhs.org/~taco/gpg.public.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.6 (GNU/Linux)
Comment: Made with pgp4pine 1.75-6

iD8DBQE71yTx6WlwGJ3ROBQRAso7AJ9Ej0XVEl5hwWX020xuJk9Iw1NGFACbBeYN 2OXKbTbAM2NbfEiSEgdbg04=
=gJlP
-----END PGP SIGNATURE-----

#7 lore raw
In reply to H . J . Lu

My general impression is that your looking for a "FAST" board, and a little endian board make for mutually exclusive requirements. Not that little endian couldn't be fast, but just about every piece of hardware I've seen running little endian has used one of the lesser mips chips in it where they've cut corners multiplexing address and data over the same pins and so forth. Someone correct me if I'm wrong, but of all the ones I've looked at, the little endian boards had the less capable hardware to boot. I think that's because the market was being driven by these little Win CE things, and CE only supports little endian.

Quoted 11 lines · H . J . Lu
Quoted 3 lines · James Simmons

I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.

I think Cobalt Qube is slow and is hard to expand the memory. I need at least 128MB RAM. Also the current mips kernel doesn't support it.

H.J.

#8 lore raw
Quoted 9 lines · J. Scott Kasten

My general impression is that your looking for a "FAST" board, and a little endian board make for mutually exclusive requirements. Not that little endian couldn't be fast, but just about every piece of hardware I've seen running little endian has used one of the lesser mips chips in it where they've cut corners multiplexing address and data over the same pins and so forth. Someone correct me if I'm wrong, but of all the ones I've looked at, the little endian boards had the less capable hardware to boot. I think that's because the market was being driven by these little Win CE things, and CE only supports little endian.

You can try a NEC DDBxxxx evaluation board with VR5000. They have jumpers to select endianness, but I never got them to work in big-endian mode.

Quoted 7 lines · H . J . Lu
Quoted 6 lines · James Simmons
Quoted 2 lines

I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.

I think Cobalt Qube is slow and is hard to expand the memory. I need at least 128MB RAM. Also the current mips kernel doesn't support it.

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

#9 lore raw
In reply to H . J . Lu
Quoted 10 lines · J. Scott Kasten

My general impression is that your looking for a "FAST" board, and a little endian board make for mutually exclusive requirements. Not that little endian couldn't be fast, but just about every piece of hardware I've seen running little endian has used one of the lesser mips chips in it where they've cut corners multiplexing address and data over the same pins and so forth. Someone correct me if I'm wrong, but of all the ones I've looked at, the little endian boards had the less capable hardware to boot. I think that's because the market was being driven by these little Win CE things, and CE only supports little endian.

Well, not quite. Linux supports LE too but the choice of LE mips desktop systems is limited.

The fastest LE cpu/board I've worked with is the Alchemy Au1000 part running at 396MHz. The board doesn't have and IDE or SCSI controller though. However, it has pcmcia and we've added support for their pcmcia controller, so I was able to use a Hitachi 2GB pcmcia ata card (looks like the IBM Microdrive). That might be one option for reasonably fast native compiles.

Pete

Quoted 15 lines · H . J . Lu
Quoted 12 lines · James Simmons
Quoted 3 lines

I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.

I think Cobalt Qube is slow and is hard to expand the memory. I need at least 128MB RAM. Also the current mips kernel doesn't support it.

H.J.

#10 lore raw
In reply to H . J . Lu
Quoted 18 lines · H . J . Lu

Hi,

I am looking for a mips machine to continue working on my mips port of RedHat. My requirements are

1. It has the stable, up to date kernel support. That means I can do

# ./configure
# make bootstrap
# make check

for gcc 3.1 without a kernel oops.

2. It has decent CPU. I hate to wait a day for

# make bootstrap
Quoted 8 lines

3. Inexpensive.

4. Support serial console.

5. Little endian is preferred.

Does anyone have any recommendations?

It appears Malta from MIPS and Ocelot Dev box from Momentum should fit your need. I think both would cost about $3000 a piece though.

Jun

#11 lore raw
In reply to H . J . Lu

Hi,

I promised you a Malta some time ago, but we have been short on the boards.
We should get some in the very near future, so I hope to be able to send you a board.
You can run the board in both endianness.
I can probably not give you a very fast system at the moment, but hopefully when we have some faster CPUs, I can ship a faster daughter card.

/Carsten

Quoted 21 lines · H . J . Lu

Hi,

I am looking for a mips machine to continue working on my mips port of RedHat. My requirements are

1. It has the stable, up to date kernel support. That means I can do

# ./configure
# make bootstrap
# make check

for gcc 3.1 without a kernel oops.

2. It has decent CPU. I hate to wait a day for

# make bootstrap

3. Inexpensive.

4. Support serial console.

Quoted 7 lines

5. Little endian is preferred.

Does anyone have any recommendations?

Thanks.

H.J.

--

_    _ ____  ___   Carsten Langgaard   Mailto:[email protected]
|\  /|||___)(___   MIPS Denmark        Direct: +45 4486 5527
| \/ |||    ____)  Lautrupvang 4B      Switch: +45 4486 5555
  TECHNOLOGIES     2750 Ballerup       Fax...: +45 4486 5556
                   Denmark             http://www.mips.com