I am looking for a mips machine
Hi,
I am looking for a mips machine to continue working on my mips port of RedHat. My requirements are
1. It has the stable, up to date kernel support. That means I can do
# ./configure # make bootstrap # make check
for gcc 3.1 without a kernel oops.
2. It has decent CPU. I hate to wait a day for
# make bootstrap
3. Inexpensive.
4. Support serial console.
5. Little endian is preferred.
Does anyone have any recommendations?
Thanks.
H.J.
Quoted 16 lines
I am looking for a mips machine to continue working on my mips port of RedHat. My requirements are
1. It has the stable, up to date kernel support. That means I can do
# ./configure # make bootstrap # make checkfor gcc 3.1 without a kernel oops.
2. It has decent CPU. I hate to wait a day for
# make bootstrap
Quoted 7 lines
3. Inexpensive.
4. Support serial console.
5. Little endian is preferred.
Does anyone have any recommendations?
I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.
Quoted 3 lines · James Simmons
I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.
I think Cobalt Qube is slow and is hard to expand the memory. I need at least 128MB RAM. Also the current mips kernel doesn't support it.
H.J.
Quoted 5 lines
Quoted 3 lines
I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.
I think Cobalt Qube is slow and is hard to expand the memory.
Slow that it is. As for memory it has two banks for 72 pin memory. I want to add memory to the Qube I have.
Quoted 1 line
Also the current mips kernel doesn't support it.
In the CVS tree I have it works and this tree is against Ralph's tree.
Quoted 8 lines · James Simmons
Quoted 5 lines
Quoted 3 lines
I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.
I think Cobalt Qube is slow and is hard to expand the memory.
Slow that it is. As for memory it has two banks for 72 pin memory. I want to add memory to the Qube I have.
I have access to a Raq 2. But it won't take my old EDO SIMMs :-). Besides, it only supports an 2.2 kernel.
H.J.
Quoted 2 lines
I have access to a Raq 2. But it won't take my old EDO SIMMs :-).
That sucks. Have you have any luck with any memory chips?
Quoted 1 line
Besides, it only supports an 2.2 kernel.
jsimmons@borgcube:~$ cat /proc/cpuinfo cpu : MIPS cpu model : Nevada V10.0 system type : Cobalt Microserver 27 BogoMIPS : 249.85 byteorder : little endian unaligned accesses : 0 wait instruction : yes microsecond timers : yes extra interrupt vector : yes hardware watchpoint : no VCED exceptions : not available VCEI exceptions : not available jsimmons@borgcube:~$ uname -nr borgcube 2.4.10-mips jsimmons@borgcube:~$
Actually I need to migrate the code to the new time and pci code. I will be sending a diff to Ralph in the next few days.
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 2 lines
I have access to a Raq 2. But it won't take my old EDO SIMMs :-). Besides, it only supports an 2.2 kernel.
well, nog exactly:
I've got a Raq 2 running 2.4.7-pre6 + pty-support here, running for 79 days now...
don't know exacty which patches i used, but i think i can figure it out, if you like...
at least one of the patches is named 'linux-2.4.7-pre6-mips-cobalt-v1.patch' ;))
it's currently used as a simpel web-server for development/test stuff.
i could supply more info if you like that....
Cheers,
Taco.
- ---
"One World, one Web, one Program" - Microsoft promo ad "Ein Volk, ein Reich, ein Fuhrer" - Adolf Hitler
- ---
GPG KeyID=0x9DD13814
GPG Fingerprint=7DF2 0E97 C5B9 6945 BD0B 3C9F E969 7018 9DD1 3814 GPG Key: http://www.taco.dhs.org/~taco/gpg.public.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.6 (GNU/Linux)
Comment: Made with pgp4pine 1.75-6
iD8DBQE71yTx6WlwGJ3ROBQRAso7AJ9Ej0XVEl5hwWX020xuJk9Iw1NGFACbBeYN 2OXKbTbAM2NbfEiSEgdbg04=
=gJlP
-----END PGP SIGNATURE-----
My general impression is that your looking for a "FAST" board, and a little endian board make for mutually exclusive requirements. Not that little endian couldn't be fast, but just about every piece of hardware I've seen running little endian has used one of the lesser mips chips in it where they've cut corners multiplexing address and data over the same pins and so forth. Someone correct me if I'm wrong, but of all the ones I've looked at, the little endian boards had the less capable hardware to boot. I think that's because the market was being driven by these little Win CE things, and CE only supports little endian.
Quoted 11 lines · H . J . Lu
Quoted 3 lines · James Simmons
I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.
I think Cobalt Qube is slow and is hard to expand the memory. I need at least 128MB RAM. Also the current mips kernel doesn't support it.
H.J.
Quoted 10 lines · J. Scott Kasten
My general impression is that your looking for a "FAST" board, and a little endian board make for mutually exclusive requirements. Not that little endian couldn't be fast, but just about every piece of hardware I've seen running little endian has used one of the lesser mips chips in it where they've cut corners multiplexing address and data over the same pins and so forth. Someone correct me if I'm wrong, but of all the ones I've looked at, the little endian boards had the less capable hardware to boot. I think that's because the market was being driven by these little Win CE things, and CE only supports little endian.
Well, not quite. Linux supports LE too but the choice of LE mips desktop systems is limited.
The fastest LE cpu/board I've worked with is the Alchemy Au1000 part running at 396MHz. The board doesn't have and IDE or SCSI controller though. However, it has pcmcia and we've added support for their pcmcia controller, so I was able to use a Hitachi 2GB pcmcia ata card (looks like the IBM Microdrive). That might be one option for reasonably fast native compiles.
Pete
Quoted 15 lines · H . J . Lu
Quoted 12 lines · James Simmons
Quoted 3 lines
I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.
I think Cobalt Qube is slow and is hard to expand the memory. I need at least 128MB RAM. Also the current mips kernel doesn't support it.
H.J.
Quoted 18 lines · H . J . Lu
Hi,
I am looking for a mips machine to continue working on my mips port of RedHat. My requirements are
1. It has the stable, up to date kernel support. That means I can do
# ./configure # make bootstrap # make checkfor gcc 3.1 without a kernel oops.
2. It has decent CPU. I hate to wait a day for
# make bootstrap
Quoted 8 lines
3. Inexpensive.
4. Support serial console.
5. Little endian is preferred.
Does anyone have any recommendations?
It appears Malta from MIPS and Ocelot Dev box from Momentum should fit your need. I think both would cost about $3000 a piece though.
Jun
Quoted 9 lines · J. Scott Kasten
My general impression is that your looking for a "FAST" board, and a little endian board make for mutually exclusive requirements. Not that little endian couldn't be fast, but just about every piece of hardware I've seen running little endian has used one of the lesser mips chips in it where they've cut corners multiplexing address and data over the same pins and so forth. Someone correct me if I'm wrong, but of all the ones I've looked at, the little endian boards had the less capable hardware to boot. I think that's because the market was being driven by these little Win CE things, and CE only supports little endian.
You can try a NEC DDBxxxx evaluation board with VR5000. They have jumpers to select endianness, but I never got them to work in big-endian mode.
Quoted 7 lines · H . J . Lu
Quoted 6 lines · James Simmons
Quoted 2 lines
I use a Cobalt Qube for alot of my developement. It works fine. I know it is not in Ralph's tree yet but I plan to send him my work soon.
I think Cobalt Qube is slow and is hard to expand the memory. I need at least 128MB RAM. Also the current mips kernel doesn't support it.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Hi,
I promised you a Malta some time ago, but we have been short on the boards.
We should get some in the very near future, so I hope to be able to send you a board.
You can run the board in both endianness.
I can probably not give you a very fast system at the moment, but hopefully when we have some faster CPUs, I can ship a faster daughter card.
/Carsten
Quoted 21 lines · H . J . Lu
Hi,
I am looking for a mips machine to continue working on my mips port of RedHat. My requirements are
1. It has the stable, up to date kernel support. That means I can do
# ./configure # make bootstrap # make checkfor gcc 3.1 without a kernel oops.
2. It has decent CPU. I hate to wait a day for
# make bootstrap3. Inexpensive.
4. Support serial console.
Quoted 7 lines
5. Little endian is preferred.
Does anyone have any recommendations?
Thanks.
H.J.
--
_ _ ____ ___ Carsten Langgaard Mailto:[email protected] |\ /|||___)(___ MIPS Denmark Direct: +45 4486 5527 | \/ ||| ____) Lautrupvang 4B Switch: +45 4486 5555 TECHNOLOGIES 2750 Ballerup Fax...: +45 4486 5556 Denmark http://www.mips.com