2 Gateways
Hello again,
I may have a common problem to solve but it seems it is harder than I thought...
I have 2 internet providers (each one having a different gateway). Behind the router there are around 100 clients that are SNAT-ed.
I want some clients to be SNAT-ed to the first provider, while the others to the second one.
The following lines should work:
iptables -t nat -A POSTROUTING -s 172.17.31.81 -j SNAT --to-source $INET_IP_1
iptables -t nat -A POSTROUTING -s 172.17.31.82 -j SNAT --to-source $INET_IP_2
But... there is a problem... I have to make the packet (after it has been SNAT-ed)
follow the gateway corresponding to the $INET_IP_1 or to the $INET_IP_2 respectively.
In my routing table I have only one default route... corresponding to one of the gateways.
Is it possible to have 2 default routes? Is there a more elegant way to solve this problem?
Is there a way to tell the routing table that every request that has the source address $INET_IP_1
follow the $GW_1, and every request that has the source address $INET_IP_2 follow the $GW_2?
Thanks in advance,
Mihai Vlad
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Mihai,
Quoted 9 lines
But... there is a problem... I have to make the packet (after it has been SNAT-ed)
follow the gateway corresponding to the $INET_IP_1 or to the $INET_IP_2 respectively.In my routing table I have only one default route... corresponding to one of the gateways.
Is it possible to have 2 default routes? Is there a more elegant way to solve this problem?
you basically want to use the 'ip route' command, and setup 2 routing tables.
Quoted 4 lines
Is there a way to tell the routing table that every request that has the source address $INET_IP_1
follow the $GW_1, and every request that has the source address $INET_IP_2 follow the $GW_2?
yup, you setup the two tables, one has GW_1 and one has GW_2, and direct traffic into the tables based on it's address.
take a look through the mailling list archives and doco on the web for examples. it's not too hard.
regards,
Signature · 10 lines
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Damion de Soto - Software Engineer email: [email protected] SnapGear - A CyberGuard Company --- ph: +61 7 3435 2809 | Custom Embedded Solutions fax: +61 7 3891 3630 | and Security Appliances web: http://www.snapgear.com ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ --- Free Embedded Linux Distro at http://www.snapgear.org --- _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 7 lines · Mihai Vlad
Is there a way to tell the routing table that every request that has the source address $INET_IP_1
follow the $GW_1, and every request that has the source address $INET_IP_2 follow the $GW_2?Thanks in advance,
Mihai Vlad
Unless I'm missing something really obvious, start here
http://lartc.org/howto/lartc.rpdb.html
and then read
http://www.linux-ip.net/html/adv-multi-internet.html
http://www.linux-ip.net/html/ch-routing.html
and finally, google "martin brown lartc changing default route" and read the messages in that thread.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hi Mihai,
You can do this by iproute and only if your box is configured as
[*] IP: advanced router
You will also need ip-utils.
"ip route show" will show the main table with all your routes but what
is most important is your default $GW_1
So, let's now create another table, with default gateway $GW_2 then,
make a rule so all from $INET_IP_2 should follow that table :
ip route add default via $GW_2 table secondary
( if iputils will scream that doesn't know who is "secondary" create "iproute2" in your "/etc" then in that new dir create and edit the file named "rt_tables" and put on the first row "10 secondary". It should look like this :
#cat /etc/iproute2/rt_tables
10 secondary
#
Then make a rule which says that everything leaving your box with ip
$INET_IP_2 should go to $GW_2 :
ip rule add from $INET_IP_2 table secondary
And that's it !
P.S. Daca iti nu iti iese da-mi un mail si vedem care e buba !
Quoted 41 lines
Hello again,
I may have a common problem to solve but it seems it is harder than I thought...
I have 2 internet providers (each one having a different gateway). Behind the router there are around 100 clients that are SNAT-ed.
I want some clients to be SNAT-ed to the first provider, while the others to
the second one.
The following lines should work:iptables -t nat -A POSTROUTING -s 172.17.31.81 -j SNAT --to-source $INET_IP_1
iptables -t nat -A POSTROUTING -s 172.17.31.82 -j SNAT --to-source $INET_IP_2But... there is a problem... I have to make the packet (after it has been SNAT-ed)
follow the gateway corresponding to the $INET_IP_1 or to the $INET_IP_2 respectively.In my routing table I have only one default route... corresponding to one of
the gateways.
Is it possible to have 2 default routes? Is there a more elegant way to solve this problem?Is there a way to tell the routing table that every request that has the source address $INET_IP_1
follow the $GW_1, and every request that has the source address $INET_IP_2 follow the $GW_2?Thanks in advance,
Mihai Vlad
Quoted 4 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Adrian Saileanu
Netmaster Communications Srl
address: Str. Ion Brezoianu Nr. 20
Sector 1, Bucuresti, Romania
office: +40 21 315 92 00
mobile: +40 723 979 586
email: [email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/