Ceil Rate
Hi all,
I just recently began using HTB to try and manage bandwidth for my network. This is the script I'm using:
/sbin/iptables -t mangle -A FORWARD -o eth1 -s ! 192.168.244.2 -j MARK --set-mark 53
tc qdisc add dev eth1 root handle 1: htb default 20
tc class add dev eth1 parent 1: classid 1:1 htb rate 100mbit burst 131072k quantum 59000
tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit quantum 1501
tc class add dev eth1 parent 1:1 classid 1:20 htb rate 1kbit ceil 100mbit burst 131072k quantum 1600
tc qdisc add dev eth1 parent 1:10 handle 10: sfq perturb 10 tc qdisc add dev eth1 parent 1:20 handle 20: sfq perturb 10
tc filter add dev eth1 protocol ip parent 1:0 prio 1 handle 53 fw flowid 1:10
The problem is I often find the rate exceeding the ceil which is 64kbit for 1:10 when I ran this command:
tc -s show class dev eth1
I'm also using a script that captures the output of the above command and feeds it to rrdtool to plot a graph of the usage and it also shows that the bandwidth being utilised exceeds 64kbit.
How can ensure that this doesn't happen? Where did I go wrong with my config?
Any help would be appreciated.
Thanks.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
You didn't set a ceil for 1:10, you only set a rate. when no ceil is specified, a subclass will borrow past its rate max if it can.
You should use:
tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit ceil 64kbit quantum 1501
And then it would use 64kbit as a hard cap, only going past it for short bursts when trying to maintain 64kbit as the average (cburst paramater can control this, but shouldn't be neccasary).
- Jody
Quoted 4 lines · On 9/30/05, [email protected] <[email protected]> wrote:
tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit quantum 1501
The problem is I often find the rate exceeding the ceil which is 64kbit for
Quoted 13 lines
1:10 when I ran this
command:tc -s show class dev eth1
I'm also using a script that captures the output of the above command and feeds it to rrdtool to plot a graph of the usage and it also shows that the
bandwidth being utilised exceeds 64kbit.How can ensure that this doesn't happen? Where did I go wrong with my config?
Quoted 9 lines
Any help would be appreciated.
Thanks.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
I thought that the default ceil was the same as the rate, or does that only apply to the root class?
Thanks for the info.
Quoted 45 lines · Jody Shumaker
You didn't set a ceil for 1:10, you only set a rate. when no ceil is specified, a subclass will borrow past its rate max if it can.
You should use:
tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit ceil 64kbit quantum 1501
And then it would use 64kbit as a hard cap, only going past it for short bursts when trying to maintain 64kbit as the average (cburst paramater can control this, but shouldn't be neccasary).
- Jody
Quoted 4 lines · On 9/30/05, [email protected] <[email protected]> wrote:
tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit quantum 1501
The problem is I often find the rate exceeding the ceil which is 64kbit for
Quoted 13 lines
1:10 when I ran this
command:tc -s show class dev eth1
I'm also using a script that captures the output of the above command and feeds it to rrdtool to plot a graph of the usage and it also shows that the
bandwidth being utilised exceeds 64kbit.How can ensure that this doesn't happen? Where did I go wrong with my config?
Quoted 9 lines
Any help would be appreciated.
Thanks.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Quoted 4 lines
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Quoted 7 lines · [email protected] wrote:
I thought that the default ceil was the same as the rate, or does that only apply to the root class?
Thanks for the info.
I just checked the documentation, and you are correct, "The default ceil is the same as the rate." However since that doesn't seem to be happening for you, I'd suggest trying to set it.
Also, it'd be helpful to include the output of 'tc -s class show dev eth1' instead of merely citing it. It would list the actual ceil being used and other useful information.
- Jody
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc