Skip to contentSkip to conversation

Ceil Rate

LARTC [email protected] 2 participants 4 messages Sep 30, 2005 – Oct 5, 2005

lore
Share & tools
lore
#0 lore raw

Hi all,

I just recently began using HTB to try and manage bandwidth for my network. This is the script I'm using:

/sbin/iptables -t mangle -A FORWARD -o eth1 -s ! 192.168.244.2 -j MARK --set-mark 53

tc qdisc add dev eth1 root handle 1: htb default 20

tc class add dev eth1 parent 1: classid 1:1 htb rate 100mbit burst 131072k quantum 59000

tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit quantum 1501
tc class add dev eth1 parent 1:1 classid 1:20 htb rate 1kbit ceil 100mbit burst 131072k quantum 1600

tc qdisc add dev eth1 parent 1:10 handle 10: sfq perturb 10 tc qdisc add dev eth1 parent 1:20 handle 20: sfq perturb 10

tc filter add dev eth1 protocol ip parent 1:0 prio 1 handle 53 fw flowid 1:10

The problem is I often find the rate exceeding the ceil which is 64kbit for 1:10 when I ran this command:

tc -s show class dev eth1

I'm also using a script that captures the output of the above command and feeds it to rrdtool to plot a graph of the usage and it also shows that the bandwidth being utilised exceeds 64kbit.

How can ensure that this doesn't happen? Where did I go wrong with my config?

Any help would be appreciated.

Thanks.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#1 lore raw

You didn't set a ceil for 1:10, you only set a rate. when no ceil is specified, a subclass will borrow past its rate max if it can.

You should use:

tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit ceil 64kbit quantum 1501

And then it would use 64kbit as a hard cap, only going past it for short bursts when trying to maintain 64kbit as the average (cburst paramater can control this, but shouldn't be neccasary).

- Jody

Quoted 4 lines · On 9/30/05, [email protected] <[email protected]> wrote:

tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit quantum 1501

The problem is I often find the rate exceeding the ceil which is 64kbit for

Quoted 13 lines

1:10 when I ran this
command:

tc -s show class dev eth1

I'm also using a script that captures the output of the above command and feeds it to rrdtool to plot a graph of the usage and it also shows that the
bandwidth being utilised exceeds 64kbit.

How can ensure that this doesn't happen? Where did I go wrong with my config?

Quoted 9 lines

Any help would be appreciated.

Thanks.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#2 lore raw
In reply to [email protected]

I thought that the default ceil was the same as the rate, or does that only apply to the root class?

Thanks for the info.

Quoted 45 lines · Jody Shumaker

You didn't set a ceil for 1:10, you only set a rate. when no ceil is specified, a subclass will borrow past its rate max if it can.

You should use:

tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit ceil 64kbit quantum 1501

And then it would use 64kbit as a hard cap, only going past it for short bursts when trying to maintain 64kbit as the average (cburst paramater can control this, but shouldn't be neccasary).

- Jody

Quoted 4 lines · On 9/30/05, [email protected] <[email protected]> wrote:

tc class add dev eth1 parent 1:1 classid 1:10 htb rate 64kbit quantum 1501

The problem is I often find the rate exceeding the ceil which is 64kbit for

Quoted 13 lines

1:10 when I ran this
command:

tc -s show class dev eth1

I'm also using a script that captures the output of the above command and feeds it to rrdtool to plot a graph of the usage and it also shows that the
bandwidth being utilised exceeds 64kbit.

How can ensure that this doesn't happen? Where did I go wrong with my config?

Quoted 9 lines

Any help would be appreciated.

Thanks.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

Quoted 4 lines

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#3 lore raw
In reply to [email protected]
Quoted 7 lines · [email protected] wrote:

I thought that the default ceil was the same as the rate, or does that only apply to the root class?

Thanks for the info.

I just checked the documentation, and you are correct, "The default ceil is the same as the rate." However since that doesn't seem to be happening for you, I'd suggest trying to set it.

Also, it'd be helpful to include the output of 'tc -s class show dev eth1' instead of merely citing it. It would list the actual ceil being used and other useful information.

- Jody
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc