Skip to contentSkip to conversation

ask some questions about u-boot's bootm command

DISCUSSION poorbeyond 2 participants 2 messages Jul 22, 2007 – Jul 24, 2007

lore
Share & tools
lore

poorbeyond

author
#0 lore raw

my cpu is 860T, using bootm command boot a linux kernel image, the following message print by smc1:

bootm 300000

## Booting image at 00300000 ...

   Image Name:   Linux-2.6.20.14
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1081591 Bytes =  1 MB

Load Address: 00100000
Entry Point: 00100000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Current stack ends at 0x01D5DB10 => set upper limit to 0x00800000 No initrd
## Transferring control to Linux (at address 00100000) ...

then, the program has no response.

i debug it througth BDM, in u-boot function "do_bootm_linux", execute at "kernel = (void (*)(bd_t *, ulong, ulong, ulong, ulong))hdr->ih_ep", the program branch to address "0x00000000", the code is shown as following:

00000000    mr    r31,r3
00000004    mr    r30,r4
00000008    mr    r29,r5
0000000C    mr    r28,r6
00000010    mr    r27,r7
00000014    bl    0x000020C8
00000018    mfmsr    r0
0000001C    ori    r0,r0,0x30
00000020    mtspr    SRR1,r0
00000024    lis    r0,0xC0002004@h
00000028    ori    r0,r0,0xC0002004@l
0000002C    mtspr    SRR0,r0
00000030    rfi

my questions are:

1. Is the code "kernel = (void (*)(bd_t *, ulong, ulong, ulong, ulong))hdr->ih_ep" branch right?

2. What's the expected code after "kernel = (void (*)(bd_t *, ulong, ulong, ulong, ulong))hdr->ih_ep"?

3. When the kernel run to the "boot/simple/head.s"?

thanks a lot

poorbeyond
2007-07-22

#1 lore raw

can u send me output of printenv in boot loader..?

Nethra

Quoted 65 lines · poorbeyond

my cpu is 860T, using bootm command boot a linux kernel image, the following message print by smc1:

bootm 300000

## Booting image at 00300000 ...

   Image Name:   Linux-2.6.20.14
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1081591 Bytes =  1 MB

Load Address: 00100000
Entry Point: 00100000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Current stack ends at 0x01D5DB10 => set upper limit to 0x00800000 No initrd
## Transferring control to Linux (at address 00100000) ...

then, the program has no response.

i debug it througth BDM, in u-boot function "do_bootm_linux", execute at "kernel = (void (*)(bd_t *, ulong, ulong, ulong, ulong))hdr->ih_ep", the program branch to address "0x00000000", the code is shown as following:

00000000    mr    r31,r3
00000004    mr    r30,r4
00000008    mr    r29,r5
0000000C    mr    r28,r6
00000010    mr    r27,r7
00000014    bl    0x000020C8
00000018    mfmsr    r0
0000001C    ori    r0,r0,0x30
00000020    mtspr    SRR1,r0
00000024    lis    r0,0xC0002004@h
00000028    ori    r0,r0,0xC0002004@l
0000002C    mtspr    SRR0,r0
00000030    rfi

my questions are:

1. Is the code "kernel = (void (*)(bd_t *, ulong, ulong, ulong, ulong))hdr->ih_ep" branch right?

2. What's the expected code after "kernel = (void (*)(bd_t *, ulong, ulong, ulong, ulong))hdr->ih_ep"?

3. When the kernel run to the "boot/simple/head.s"?

thanks a lot

poorbeyond
2007-07-22

_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded

Signature · 2 lines
View this message in context: http://www.nabble.com/ask-some-questions-about-u-boot%27s-bootm-command-tf4124319.html#a11761280
Sent from the linuxppc-embedded mailing list archive at Nabble.com.