Hardware debuggers for PPC74xx G4 CPUs
I'm trying to debug a kernel lockup that occurs on my machine with all kernel versions >2.6.16. I don't have a clue what the root cause of this lockup is, thus I'm thinking about using a hardware debugger. Can anybody recommend a reasonably cheap hardware debugger that works with G4 CPUs and can interact with GDB/DDD?
regards,
Gerhard
Signature · 2 lines
Ist Ihr Browser Vista-kompatibel? Jetzt die neuesten Browser-Versionen downloaden: http://www.gmx.net/de/go/browser
Quoted 5 lines · Gerhard Pircher
I'm trying to debug a kernel lockup that occurs on my machine with all kernel versions >2.6.16. I don't have a clue what the root cause of this lockup is, thus I'm thinking about using a hardware debugger. Can anybody recommend a reasonably cheap hardware debugger that works with G4 CPUs and can interact with GDB/DDD?
Abatron BDI-2000.
Signature · 4 lines
Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd. [email protected] (403) 399-0195
Quoted 8 lines · Grant Likely
Quoted 5 lines · Gerhard Pircher
I'm trying to debug a kernel lockup that occurs on my machine with all kernel versions >2.6.16. I don't have a clue what the root cause of this lockup is, thus I'm thinking about using a hardware debugger. Can anybody recommend a reasonably cheap hardware debugger that works with G4 CPUs and can interact with GDB/DDD?
Abatron BDI-2000.
Oops, but that's not all that cheap. ($2750USD). You might try looking at the Macraigor Wiggler
(http://www.macraigor.com/wiggler.htm), but it has limited powerpc support.
Cheers,
g.
Signature · 4 lines
Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd. [email protected] (403) 399-0195
Quoted 8 lines · Grant Likely
Quoted 5 lines · Gerhard Pircher
I'm trying to debug a kernel lockup that occurs on my machine with all kernel versions >2.6.16. I don't have a clue what the root cause of this lockup is, thus I'm thinking about using a hardware debugger. Can anybody recommend a reasonably cheap hardware debugger that works with G4 CPUs and can interact with GDB/DDD?
Abatron BDI-2000.
Does anyone have the detailed doc needed to implement the software for a PPC hardware debugger? Dominic, the author of OpenOCD, has said he will take a look at adding PPC support if someone can supply him with the right doc.
I've requested it from my Freescale rep. They sent me all of the hardware info but none of the software info. They can't seem to figure out what I'm asking for.
Signature · 2 lines
Jon Smirl [email protected]
Quoted 8 lines · Grant Likely
Quoted 7 lines · Grant Likely
Quoted 5 lines · Gerhard Pircher
I'm trying to debug a kernel lockup that occurs on my machine with all kernel versions >2.6.16. I don't have a clue what the root cause of this lockup is, thus I'm thinking about using a hardware debugger. Can anybody recommend a reasonably cheap hardware debugger that works with G4 CPUs and can interact with GDB/DDD?
Quoted 6 lines
Quoted 1 line
Abatron BDI-2000.
Oops, but that's not all that cheap. ($2750USD). You might try looking at the Macraigor Wiggler
(http://www.macraigor.com/wiggler.htm), but it has limited powerpc support.
Here are the choices:
http://www.macraigor.com/cpus.htm
Quoted 14 lines
Cheers,
g.--
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.
[email protected]
(403) 399-0195
_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-dev
Signature · 2 lines
Jon Smirl [email protected]
-------- Original-Nachricht --------
Quoted 10 lines
Datum: Tue, 13 Nov 2007 17:10:29 -0500
Von: "Jon Smirl" <[email protected]>
An: "Grant Likely" <[email protected]>
CC: "Gerhard Pircher" <[email protected]>, [email protected]
Betreff: Re: Hardware debuggers for PPC74xx G4 CPUsQuoted 3 lines · Grant Likely
Quoted 1 line · Grant Likely
Abatron BDI-2000.
Quoted 7 lines
Quoted 4 lines
Oops, but that's not all that cheap. ($2750USD). You might try looking at the Macraigor Wiggler
(http://www.macraigor.com/wiggler.htm), but it has limited powerpc support.Here are the choices:
http://www.macraigor.com/cpus.htm
Looks like the Abatron BDI-2000 is the cheapest hardware debugger that supports 74xx G4 CPUs. :-(
Thanks!
Gerhard
Signature · 2 lines
GMX FreeMail: 1 GB Postfach, 5 E-Mail-Adressen, 10 Free SMS. Alle Infos und kostenlose Anmeldung: http://www.gmx.net/de/go/freemail
Quoted 3 lines · Grant Likely
Quoted 1 line
Abatron BDI-2000.
Oops, but that's not all that cheap. ($2750USD).
If you place any value on your time or development schedule, it's a bargain. Just plug it in, and it works. Choose any of your favorite debugger front ends, from none with just a telnet interface, to remote gdb, ddd, or several Eclipse options. Several choices of host OS. It will pay you back in development and debugging time savings over and over.
-- Dan
Quoted 9 lines · Dan Malek
Quoted 3 lines · Grant Likely
Quoted 1 line
Abatron BDI-2000.
Oops, but that's not all that cheap. ($2750USD).
If you place any value on your time or development schedule, it's a bargain.
That only applies for cases where time means money, i.e. professional work. Spending three thousand dollars to debug a board that you spent a few hundred dollars buying just for a hobby is pretty crazy.
-Olof
Quoted 6 lines · Olof Johansson
Quoted 5 lines · Dan Malek
Quoted 2 lines · Grant Likely
Quoted 1 line
Abatron BDI-2000.
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
Oops, but that's not all that cheap. ($2750USD).
If you place any value on your time or development schedule, it's a bargain.
That only applies for cases where time means money, i.e. professional work. Spending three thousand dollars to debug a board that you spent a few hundred dollars buying just for a hobby is pretty crazy.
That's why Dominic wants to get OpenOCD running on the PowerPC. All we need is the programming documentation for controlling the CPU via the debug hardware.
Obviously this documentation exist, all of the commercial vendors had to have it to develop their debuggers. Maybe it is already out there and we just don't know where to look.
Signature · 2 lines
Jon Smirl [email protected]
Quoted 16 lines · Gerhard Pircher
-------- Original-Nachricht --------
Quoted 15 lines
Datum: Tue, 13 Nov 2007 17:10:29 -0500
Von: "Jon Smirl" <[email protected]>
An: "Grant Likely" <[email protected]>
CC: "Gerhard Pircher" <[email protected]>, [email protected]
Betreff: Re: Hardware debuggers for PPC74xx G4 CPUsQuoted 7 lines · Grant Likely
Quoted 1 line · Grant Likely
Abatron BDI-2000.
Oops, but that's not all that cheap. ($2750USD). You might try looking at the Macraigor Wiggler
(http://www.macraigor.com/wiggler.htm), but it has limited powerpc support.
Quoted 4 lines
Quoted 2 lines
Here are the choices:
http://www.macraigor.com/cpus.htmLooks like the Abatron BDI-2000 is the cheapest hardware debugger that supports 74xx G4 CPUs. :-(
Do you have the appropriate connector for it on the motherboard as well ? If not, then you are out of luck...
Ben.
Quoted 4 lines
That's why Dominic wants to get OpenOCD running on the PowerPC. All we need is the programming documentation for controlling the CPU via the debug hardware.
Note that this is basically different for every CPU around.
Quoted 3 lines
Obviously this documentation exist, all of the commercial vendors had to have it to develop their debuggers. Maybe it is already out there and we just don't know where to look.
Ben.
Quoted 6 lines · Benjamin Herrenschmidt
Quoted 4 lines
That's why Dominic wants to get OpenOCD running on the PowerPC. All we need is the programming documentation for controlling the CPU via the debug hardware.
Note that this is basically different for every CPU around.
I'd like to get it for the MPC5200 because of the project I am working on, an open source audio device. It would be nice if there was a cheap hardware debugger available for hackers to use on it. Maybe one of the Freescale developers will see this and send me the right docs.
Is it radically different? Dominic has been able to support every ARM 7/9 chip he can get his hands on without too much trouble once the core support was written. I don't think he has ARM 11 working yet.
Quoted 9 lines
Quoted 4 lines
Obviously this documentation exist, all of the commercial vendors had to have it to develop their debuggers. Maybe it is already out there and we just don't know where to look.
Ben.
Signature · 2 lines
Jon Smirl [email protected]
-------- Original-Nachricht --------
Quoted 18 lines
Datum: Wed, 14 Nov 2007 12:17:09 +1100
Von: Benjamin Herrenschmidt <[email protected]>
An: Gerhard Pircher <[email protected]>
CC: Jon Smirl <[email protected]>, [email protected], [email protected]
Betreff: Re: Hardware debuggers for PPC74xx G4 CPUsQuoted 5 lines · Gerhard Pircher
-------- Original-Nachricht --------
Quoted 4 lines
Datum: Tue, 13 Nov 2007 17:10:29 -0500
Von: "Jon Smirl" <[email protected]>
An: "Grant Likely" <[email protected]>
CC: "Gerhard Pircher" <[email protected]>,Quoted 4 lines
Quoted 4 lines
Betreff: Re: Hardware debuggers for PPC74xx G4 CPUs
Here are the choices:
http://www.macraigor.com/cpus.htm
Quoted 7 lines
Quoted 2 lines
Looks like the Abatron BDI-2000 is the cheapest hardware debugger that supports 74xx G4 CPUs. :-(
Do you have the appropriate connector for it on the motherboard as well ? If not, then you are out of luck...
Ben.
Yes, the connector is on the CPU module.
Gerhard
Signature · 2 lines
Psssst! Schon vom neuen GMX MultiMessenger gehört? Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger
Quoted 6 lines · Jon Smirl
Quoted 4 lines · Benjamin Herrenschmidt
Quoted 3 lines
That's why Dominic wants to get OpenOCD running on the PowerPC. All we need is the programming documentation for controlling the CPU via the debug hardware.
Note that this is basically different for every CPU around.
Quoted 13 lines
I'd like to get it for the MPC5200 because of the project I am working on, an open source audio device. It would be nice if there was a cheap hardware debugger available for hackers to use on it. Maybe one of the Freescale developers will see this and send me the right docs.
Is it radically different? Dominic has been able to support every ARM 7/9 chip he can get his hands on without too much trouble once the core support was written. I don't think he has ARM 11 working yet.
Quoted 4 lines
Quoted 3 lines
Obviously this documentation exist, all of the commercial vendors had to have it to develop their debuggers. Maybe it is already out there and we just don't know where to look.
Ben.
DISCLAIMER: Extrapolating grossly from almost no knowledge!
My understanding is that the Freescale PPC debugger interface is based on the JTAG interface using a proprietary command set. Basically, if you do their magic BDM (JTAG extension) command, you get into an internal scan chain that allows you to read/write the processor internals (registers).
The problems are many...
* The documentation is only available under NDA, a problem for open source debuggers.
* The scan chain is different on every processor, and may be different on different revisions of the same processor.
* If you mess up with JTAG, you will probably burn up the CPU. Very literally. I've seen it done. Twice. (Thankfully not my screwup, and it wasn't a PPC so it deserved to die. ;-) The internal scan chain is probably safer, but YMMV.
gvb
Quoted 29 lines · Jerry Van Baren
Quoted 6 lines · Jon Smirl
Quoted 4 lines · Benjamin Herrenschmidt
Quoted 3 lines
That's why Dominic wants to get OpenOCD running on the PowerPC. All we need is the programming documentation for controlling the CPU via the debug hardware.
Note that this is basically different for every CPU around.
Quoted 13 lines
I'd like to get it for the MPC5200 because of the project I am working on, an open source audio device. It would be nice if there was a cheap hardware debugger available for hackers to use on it. Maybe one of the Freescale developers will see this and send me the right docs.
Is it radically different? Dominic has been able to support every ARM 7/9 chip he can get his hands on without too much trouble once the core support was written. I don't think he has ARM 11 working yet.
Quoted 4 lines
Quoted 3 lines
Obviously this documentation exist, all of the commercial vendors had to have it to develop their debuggers. Maybe it is already out there and we just don't know where to look.
Ben.
DISCLAIMER: Extrapolating grossly from almost no knowledge!
My understanding is that the Freescale PPC debugger interface is based on the JTAG interface using a proprietary command set. Basically, if you do their magic BDM (JTAG extension) command, you get into an internal scan chain that allows you to read/write the processor internals (registers).
Quoted 3 lines
The problems are many...
* The documentation is only available under NDA, a problem for open source debuggers.
This is what we need. I would like it specifically for the mpc5200. But we want to use it in OpenOCD so NDA won't work.
Quoted 2 lines
* The scan chain is different on every processor, and may be different on different revisions of the same processor.
Hopefully the doc will cover this.
Quoted 4 lines
* If you mess up with JTAG, you will probably burn up the CPU. Very literally. I've seen it done. Twice. (Thankfully not my screwup, and it wasn't a PPC so it deserved to die. ;-) The internal scan chain is probably safer, but YMMV.
Dominic is way experienced implementing JTAG for ARM CPUs. He has done several dozen interfaces. ARM doesn't have any problems releasing their debugging info.
I've also lined up a mpc5200 development board vendor who wants a cheap mpc5200 JTAG too and is willing to supply him with target hardware.
JTAG hardware would be something similar to this:
http://www.amontec.com/jtagkey-tiny.shtml
So $30-40 for hardware with free OpenOCD software and you have JTAG for the mpc5200.
This puts it in the range of classroom use.
The few embedded classes I've been around lately are being taught on ARM hardware because it is so cheap. Development boards and the JTAG can be had for under $100.
For example check out this store, it carries hundreds of ARM products and almost no PowerPC ones.
http://microcontrollershop.com
Signature · 2 lines
Jon Smirl [email protected]
Quoted 6 lines · In message <[email protected]> you…
Quoted 3 lines
* The documentation is only available under NDA, a problem for open source debuggers.
This is what we need. I would like it specifically for the mpc5200. But we want to use it in OpenOCD so NDA won't work.
It doesn't work. Been there a logn time ago. It's and endless fingerpointing. Freescale (by then: Motorola) says they cannot
release any information because of their contracts with IBM, and vice versa.
Quoted 3 lines
Dominic is way experienced implementing JTAG for ARM CPUs. He has done several dozen interfaces. ARM doesn't have any problems releasing their debugging info.
JTAG is simple, but you don't get the necessery information for the COP (= debug) interface.
Best regards,
Wolfgang Denk
Signature · 6 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: [email protected] Genius doesn't work on an assembly line basis. You can't simply say, "Today I will be brilliant." -- Kirk, "The Ultimate Computer", stardate 4731.3
Quoted 5 lines · Wolfgang Denk
Quoted 4 lines · In message <[email protected]> you…
Quoted 3 lines
* The documentation is only available under NDA, a problem for open source debuggers.
Quoted 7 lines
Quoted 2 lines
This is what we need. I would like it specifically for the mpc5200. But we want to use it in OpenOCD so NDA won't work.
It doesn't work. Been there a logn time ago. It's and endless fingerpointing. Freescale (by then: Motorola) says they cannotrelease any information because of their contracts with IBM, and vice versa.
It seems like AMCC does provide the necessary infos for 4xx processors though. Jon, do you think what they provide is enough to use an open source debugger ?
Ben.
Quoted 10 lines · Benjamin Herrenschmidt
Quoted 8 lines · Wolfgang Denk
Quoted 6 lines · In message <[email protected]> you…
Quoted 3 lines
* The documentation is only available under NDA, a problem for open source debuggers.
This is what we need. I would like it specifically for the mpc5200. But we want to use it in OpenOCD so NDA won't work.
Quoted 8 lines
Quoted 4 lines
It doesn't work. Been there a logn time ago. It's and endless fingerpointing. Freescale (by then: Motorola) says they cannotrelease any information because of their contracts with IBM, and vice versa.
It seems like AMCC does provide the necessary infos for 4xx processors though. Jon, do you think what they provide is enough to use an open source debugger ?
Do you have a link to the info?
Quoted 5 lines
Ben.
Signature · 2 lines
Jon Smirl [email protected]
Quoted 6 lines · Jon Smirl
Quoted 1 line
It seems like AMCC does provide the necessary infos for 4xx
processors
Quoted 2 lines
though. Jon, do you think what they provide is enough to use an open source debugger ?
Do you have a link to the info?
Not at hand, but easy to find from AMCC main product page, you can then go to the various eval board download pages, and some of the d/l are infos for JTAG debugger manufacturers.
Ben.
Quoted 4 lines · Benjamin Herrenschmidt
Quoted 2 lines · Jon Smirl
Quoted 1 line
It seems like AMCC does provide the necessary infos for 4xx
processors
Quoted 8 lines
Quoted 4 lines
Quoted 2 lines
though. Jon, do you think what they provide is enough to use an open source debugger ?
Do you have a link to the info?
Not at hand, but easy to find from AMCC main product page, you can then go to the various eval board download pages, and some of the d/l are infos for JTAG debugger manufacturers.
Dominick Rath wrote OpenOCD (open source JTAG) as his senior thesis in college, he graduated this spring and has a job now. I've sent mail to him but he may be a lost cause.
Thesis: http://developer.berlios.de/docman/display_doc.php?docid=1367&group_id=4148
Low cost dev tools are an important part of the CPU selection process. We went through four ARM CPUs before deciding on the MPC5200. We were able to get ARM eval boards and JTAGs for under $500 for each of the eval CPUs. We used the low cost evals to screen the CPUs, we didn't want spend $5-10K until we are 90% sure we are going to use the CPU. I returned one $5K eval board, it was a pain and it took over six months to get a refund.
We have also learned the hard way about "port and forget" several of the CPUs we picked had Linux ports, but the ports were five years old. When we pushed the vendors for more recent kernels the typical answer was, send us $50,000 and we'll see what we can do. We're not going to send in $50K for a CPU we haven't decided to use, that answer simply resulted in us changing CPUs. An example of this is the NXP LPC3180, $9 with a FPU, but only a 2.6.5 kernel.
I've also only seen ARM CPUs being used in schools. You can get ARM eval boards and a JTAG for under $100 on some ARM CPUs. AFAIK there is no low cost PowerPC option suitable for classroom use.
Signature · 2 lines
Jon Smirl [email protected]
Quoted 5 lines · Jon Smirl
Quoted 4 lines · Benjamin Herrenschmidt
Quoted 2 lines · Jon Smirl
Quoted 1 line
It seems like AMCC does provide the necessary infos for 4xx
processors
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines
Quoted 2 lines
though. Jon, do you think what they provide is enough to use an open source debugger ?
Do you have a link to the info?
Not at hand, but easy to find from AMCC main product page, you can then go to the various eval board download pages, and some of the d/l are infos for JTAG debugger manufacturers.
Grant, I heard back from the Amontec (a JTAG company) developers. They are interested in doing an open JTAG for the Xilinx Microblaze. Is that the FPGA you've been working with?
Signature · 2 lines
Jon Smirl [email protected]
Quoted 11 lines · Jon Smirl
Quoted 10 lines · Jon Smirl
Quoted 9 lines · Benjamin Herrenschmidt
Quoted 6 lines · Jon Smirl
Quoted 1 line
It seems like AMCC does provide the necessary infos for 4xx
processors
Quoted 2 lines
though. Jon, do you think what they provide is enough to use an open source debugger ?
Do you have a link to the info?
Quoted 7 lines
Quoted 3 lines
Quoted 3 lines
Not at hand, but easy to find from AMCC main product page, you can then go to the various eval board download pages, and some of the d/l are infos for JTAG debugger manufacturers.
Grant, I heard back from the Amontec (a JTAG company) developers. They are interested in doing an open JTAG for the Xilinx Microblaze. Is that the FPGA you've been working with?
Yes, the FPGA I'm using can host a Microblaze design; except my work has focused on the ppc405 hard IP core instead of the microblaze core.
Regardless, this sounds interesting. Can you get JTAG debug info out of Xilinx?
Cheers,
g.
.
Quoted 5 lines
--
Jon Smirl
[email protected]
Signature · 4 lines
Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd. [email protected] (403) 399-0195