ath9k WMP300nv2 (AR5416)
Hello Luis
thanks for all your mails they have helped.
Today i have solved my problem with the crda-1.0.1-r1.
Problemdiscription:
Only crda-0.9.5 works correct with my system. "crda-1.0.1-r1 or crda-1.0.1 dont call the second part of the frequenzes"
Solution:
Newest udev + newest hal + newest hal-info + newest cryptsetup from the gentoo package (portage) tree did the job.
Now i have the next question:
is this normal that i have to reload after each reboot my cfg80211, mac80211 and ath9k? I have installed compat-wireless-2009-02-06 but this was since i used my first dirver from your hompage. My system is loading automatically at boot cfg80211 mac80211 and ath9k but if i dont reload the driver the network cant start.
Oh the newest driver (compat-wireless-2009-02-06) has a easter egg cause the led of the network card is blinking after loading ath9k.
Please dont misunderstand me now this is the first time that the led on my LinksysWMP300nv2 works correctly.
Thanks for helping
Well evening
Alexander Bartha
Signature · 1 line
Psssst! Schon vom neuen GMX MultiMessenger geh?rt? Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger01
Quoted 6 lines · Alexander Bartha
Hello Luis
thanks for all your mails they have helped.
Today i have solved my problem with the crda-1.0.1-r1.
Quoted 8 lines
Problemdiscription:
Only crda-0.9.5 works correct with my system. "crda-1.0.1-r1 or crda-1.0.1 dont call the second part of the frequenzes"Solution:
Newest udev + newest hal + newest hal-info + newest cryptsetup from the gentoo package (portage) tree did the job.Now i have the next question:
is this normal that i have to reload after each reboot my cfg80211, mac80211 and ath9k? I have installed compat-wireless-2009-02-06 but this was since i used my first dirver from your hompage. My system is loading automatically at boot cfg80211 mac80211 and ath9k but if i dont reload the driver the network cant start.
Nope, you should not need to reload the modules unless you are upgrading to a new set of modules. Can you explain what issues you have during a fresh boot and fresh install of compat-wireless?
Are you using wpa_supplicant? Are you using Network Manager? Are you using encryption? Are you using 11n?
Good to hear.
Luis
hello Luis,
Hardware:
Wireless Card: LinksysWMP300Nv2
Wireless Router: LinksysWRT160
Router Wireless Config: 802.11N, Channel 12 (because there are many routers in the neighborhood using the lower channels)
SecurityMode: WPA2-Personal, Encryption: TKIP or AES
Packages:
Kernel: gentoo-sources-2.6.28-r1
linux-headers-2.6.28-r1
wpa_supplicant-0.6.4
compat-wireless-2009-02-14
iw-0.9.9
wireless-tools-29
my wpa_supplicant.conf:
update_config=1
ctrl_interface=/var/run/wpa_supplicant
eapol_version=2
fast_reauth=1
# Ensure that only root can read the WPA configuration #ctrl_interface_group=0
#
# Let wpa_supplicant take care of scanning and AP selection ap_scan=1
#country=AT
network={
ssid="MySSid"
# scan_ssid=1
proto=RSN
key_mgmt=WPA-PSK
pairwise=TKIP CCMP
group=TKIP CCMP
psk="MyPsk"
priority=2
}
(END)
My Network-Konfiguration-File:/etc/init.d/net
modules=( "wpa_supplicant" )
wpa_supplicant_wlan0="-Dwext"
config_wlan0=( "dhcp" )
dhcpcd_wlan0="-t 10"
dhcp_wlan0="nonis"
channel_wlan0="12"
dns_domain_lo="localdnsdomain"
Error description:
When i boot my System i have to rmmod cfg80211 mac80211 ath9k + modprobe ath9k otherwise my Wlan Card (LinksysWMP300Nv2) does not
work --the leds on my WlanCard will be turned off when wpa_supplicant is starting! After the reload the WlanCard work fine.
The goal at this problem is that in var/log/messages i have the same output as my problem with crda-0.9.5 (the second part of the
frequences of crda isnt there).
Output:
[ 6.422739] cfg80211: Using static regulatory domain info [ 6.422743] cfg80211: Regulatory domain: US [ 6.422746] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 6.422751] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 6.422756] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.422760] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.422765] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.422770] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.422774] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 6.422779] cfg80211: Calling CRDA for country: US [ 6.491245] ath9k 0000:04:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 6.507775] dib0700: loaded with support for 8 different device-types [ 6.507803] dvb_usb_dib0700 1-6:1.0: usb_probe_interface [ 6.507809] dvb_usb_dib0700 1-6:1.0: usb_probe_interface - got id [ 6.508112] dvb-usb: found a 'Terratec Cinergy DT USB XS Diversity' in cold state, will try to load a firmware [ 6.508118] usb 1-6: firmware: requesting dvb-usb-dib0700-1.20.fw [ 6.704575] hub 4-0:1.0: hub_suspend [ 6.704587] usb usb4: bus auto-suspend [ 6.704590] usb usb4: suspend_rh [ 6.919213] phy0: Selected rate control algorithm 'ath9k_rate_control' [ 6.924986] cfg80211: Calling CRDA for country: AT [ 6.925034] Registered led device: ath9k-phy0::radio [ 6.925058] Registered led device: ath9k-phy0::assoc [ 6.925083] Registered led device: ath9k-phy0::tx [ 6.925110] Registered led device: ath9k-phy0::rx [ 6.925138] phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81: mem=0xf9140000, irq=20 [ 6.925200] EMU10K1_Audigy 0000:04:01.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 6.930218] Installing spdif_bug patch: Audigy 2 ZS [SB0350] [ 6.947297] modprobe used greatest stack depth: 5956 bytes left [ 7.510643] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw' [ 7.713502] dib0700: firmware started successfully. [ 8.214020] dvb-usb: found a 'Terratec Cinergy DT USB XS Diversity' in warm state. [ 8.214077] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 8.214313] DVB: registering new adapter (Terratec Cinergy DT USB XS Diversity) [ 8.410142] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)... [ 8.569765] DiB0070: successfully identified [ 8.569771] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 8.570046] DVB: registering new adapter (Terratec Cinergy DT USB XS Diversity) [ 8.703395] DVB: registering adapter 1 frontend 0 (DiBcom 7000PC)... [ 8.862768] DiB0070: successfully identified [ 8.862776] dvb-usb: Terratec Cinergy DT USB XS Diversity successfully initialized and connected. [ 8.862934] usbcore: registered new interface driver dvb_usb_dib0700 [ 8.863139] modprobe used greatest stack depth: 4828 bytes left [ 11.888046] EXT3 FS on sda3, internal journal [ 12.362694] fuse init (API version 7.10) [ 12.384776] NTFS driver 2.1.29 [Flags: R/O MODULE]. [ 12.398131] DLM (built Feb 10 2009 21:16:48) installed [ 12.429838] rtc_cmos 00:03: RTC can wake from S4 [ 12.430015] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 12.430049] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs [ 12.891170] XFS mounting filesystem sda6 [ 12.949000] Ending clean XFS mount for filesystem: sda6 [ 12.984465] kjournald starting. Commit interval 5 seconds [ 12.984713] EXT3 FS on sda11, internal journal [ 12.984721] EXT3-fs: mounted filesystem with journal data mode. [ 13.004941] kjournald starting. Commit interval 5 seconds [ 13.005191] EXT3 FS on sda12, internal journal [ 13.005198] EXT3-fs: mounted filesystem with journal data mode. [ 13.055841] XFS mounting filesystem sda5 [ 13.111428] Ending clean XFS mount for filesystem: sda5 [ 13.158084] XFS mounting filesystem sda7 [ 13.204406] Ending clean XFS mount for filesystem: sda7 [ 13.246122] XFS mounting filesystem sda8 [ 13.303238] Ending clean XFS mount for filesystem: sda8 [ 13.341860] XFS mounting filesystem sda13 [ 13.670415] Ending clean XFS mount for filesystem: sda13 [ 13.842149] Adding 1004052k swap on /dev/sda2. Priority:-1 extents:1 across:1004052k [ 17.638040] uvesafb: mode switch failed (eax=0x34f, err=0). Trying again with default timings. [ 19.733463] uvesafb: mode switch failed (eax=0x34f, err=0). Trying again with default timings. [ 21.684544] ADDRCONF(NETDEV_UP): wlan0: link is not ready
if i dont reload the modules "ADDRCONF(NETDEV_UP): wlan0: link is not ready" is the last relevant message in /var/log/messages! if i only stop and start my /etc/init.d/net.wlan0 init script it also fails with the same output in var log message "link is not ready". After boot when i dont relaod cfg, mac, ath9k "iwlist channel" knows only channel 1-11. But when i am reloading cfg, mac and ath9k "iwlist channel" knows Channel 1-13.
My Ap is working on Channel 12!
Clear if he dont knows channel 12 and channel 13 he could not connect to my AP.
Is there any posibility to get it work without the relaod of cfg80211 mac80211 ath9k???
PS: I have tried the kernel from linux-wireless (wireless-testing.git 2.6.29-rc4 wow thats new!!!) but the problem was the same.
Maybe my partition layout is relevant to that problem (mounting some partition to late???) but i dont think so. fstab:
/dev/sda1 /boot ext2 noatime 1 2 /dev/sda3 / ext3 noatime 0 1 /dev/sda6 /usr xfs noatime 0 1 /dev/sda11 /usr/bin ext3 noatime 0 1 /dev/sda12 /usr/sbin ext3 noatime 0 1 /dev/sda2 none swap sw 0 0 /dev/sda5 /home xfs noatime 0 1 /dev/sda7 /opt xfs noatime 0 1 /dev/sda8 /var xfs noatime 0 1 /dev/sda13 /archiv xfs noatime 0 1 tmpfs /dev/shm tmpfs defaults 0 0 tmpfs /tmp tmpfs defaults 0 0 /dev/hda /mnt/dvd auto noauto,user,users,ro 0 0 /dev/fd0 /mnt/floppy auto noauto 0 0
Well evening from Vienna
Signature · 2 lines
Jetzt 1 Monat kostenlos! GMX FreeDSL - Telefonanschluss + DSL f?r nur 17,95 Euro/mtl.!* http://dsl.gmx.de/?ac=OM.AD.PD003K11308T4569a
Quoted 85 lines · Alexander Bartha
hello Luis,
Hardware:
Wireless Card: LinksysWMP300Nv2
Wireless Router: LinksysWRT160
Router Wireless Config: 802.11N, Channel 12 (because there are many routers in the neighborhood using the lower channels)
SecurityMode: WPA2-Personal, Encryption: TKIP or AESPackages:
Kernel: gentoo-sources-2.6.28-r1
linux-headers-2.6.28-r1
wpa_supplicant-0.6.4
compat-wireless-2009-02-14
iw-0.9.9
wireless-tools-29my wpa_supplicant.conf:
update_config=1ctrl_interface=/var/run/wpa_supplicant
eapol_version=2
fast_reauth=1# Ensure that only root can read the WPA configuration #ctrl_interface_group=0
#
# Letwpa_supplicanttake care of scanning and AP selection ap_scan=1
#country=ATnetwork={
ssid="MySSid"
# scan_ssid=1
proto=RSN
key_mgmt=WPA-PSK
pairwise=TKIP CCMP
group=TKIP CCMP
psk="MyPsk"
priority=2
}
(END)My Network-Konfiguration-File:/etc/init.d/net
modules=( "
wpa_supplicant" )
wpa_supplicant_wlan0="-Dwext"
config_wlan0=( "dhcp" )
dhcpcd_wlan0="-t 10"
dhcp_wlan0="nonis"
channel_wlan0="12"
dns_domain_lo="localdnsdomain"Error description:
When i boot my System i have to rmmod cfg80211 mac80211 ath9k + modprobe ath9k otherwise my Wlan Card (LinksysWMP300Nv2) does not
work --the leds on my WlanCard will be turned off when
wpa_supplicantis starting! After the reload the WlanCard work fine.The goal at this problem is that in var/log/messages i have the same output as my problem with crda-0.9.5 (the second part of the
frequences of crda isnt there).
Output:
[ 6.422739] cfg80211: Using static regulatory domain info [ 6.422743] cfg80211: Regulatory domain: US [ 6.422746] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 6.422751] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 6.422756] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.422760] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.422765] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.422770] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.422774] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 6.422779] cfg80211: Calling CRDA for country: US [ 6.491245] ath9k 0000:04:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 6.507775] dib0700: loaded with support for 8 different device-types [ 6.507803] dvb_usb_dib0700 1-6:1.0: usb_probe_interface [ 6.507809] dvb_usb_dib0700 1-6:1.0: usb_probe_interface - got id [ 6.508112] dvb-usb: found a 'Terratec Cinergy DT USB XS Diversity' in cold state, will try to load a firmware [ 6.508118] usb 1-6: firmware: requesting dvb-usb-dib0700-1.20.fw [ 6.704575] hub 4-0:1.0: hub_suspend [ 6.704587] usb usb4: bus auto-suspend
Quoted 8 lines
[ 6.704590] usb usb4: suspend_rh [ 6.919213] phy0: Selected rate control algorithm 'ath9k_rate_control' [ 6.924986] cfg80211: Calling CRDA for country: AT [ 6.925034] Registered led device: ath9k-phy0::radio [ 6.925058] Registered led device: ath9k-phy0::assoc [ 6.925083] Registered led device: ath9k-phy0::tx [ 6.925110] Registered led device: ath9k-phy0::rx [ 6.925138] phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81: mem=0xf9140000, irq=20
<-- snip -->
Quoted 1 line
if i dont reload the modules "
ADDRCONF(NETDEV_UP): wlan0: link is not ready" is the last relevant message in/var/log/messages!
That is not a critical message, it means nothing bad. It just means your card is not associated yet. Once it gets associated, you "link" goes up.
Quoted 1 line
if i only stop and start my
/etc/init.d/net.wlan0init script it also fails with the same output in var log message "link is not ready".
That is not bad, it just means you are not associated.
Quoted 1 line
After boot when i dont relaod cfg, mac, ath9k "iwlist channel" knows only channel 1-11.
I believe Gentoo crda package may be installing the udev rule in the wrong place. We used to use /lib/udev/rules.d and recently started using /lib/udev/rules.d/ which seems to be more of an appropriate place. Check which one you have. If you have both remove both and try in only one location.
Can you recompile and install compat-wireless with this added to config.mk:
CONFIG_ATH9K_DEBUG=y
Then load ath9k like this:
modprobe ath9k debug=0x00000080
Before loading ath9k remember to unload all wireless modules you can do that from compat-wireless by doing:
make unload
Then provide the output of:
iw list
Quoted 2 lines
But when i am reloading cfg, mac and
ath9k "iwlist channel" knows Channel 1-13.
There may be an issue with the udev rule location, here's a backport of a patch I just posted though which may help too since you are reloading right now (but reloading should not be required).
Luis
-------------- next part --------------
A non-text attachment was scrubbed...
Name: same-hint.patch
Type: text/x-patch
Size: 1281 bytes
Desc: not available
Url : http://lists.ath9k.org/pipermail/ath9k-devel/attachments/20090214/c9b10c9f/attachment.bin
Hello Luis,
i have rebuild compat-wireless with CONFIG_ATH9K_DEBUG=y in config.mk
then -- make unload -- modprobe ath9k debug=0x00000080 --
iw list-- (Output)
-2009-02-16 # iw list
Wiphy phy0
Band 1:
HT capabilities: 0x104e
* 20/40 MHz operation
* SM PS disabled
* 40 MHz short GI
* max A-MSDU len 3839
* DSSS/CCK 40 MHz
HT A-MPDU factor: 0x0003 (65535 bytes)
HT A-MPDU density: 0x0006 (8 usec)
HT MCS set: ff ff 00 00 00 00 00 00 00 00 00 00 01 00 00 00
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Bitrates:
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Supported interface modes:
* IBSS
* Station
* AP
* AP(VLAN)
* Monitor
Looks good but after boot i never have channel 12 or 13.
The led on my LinksysWMP300Nv2 Card turned off after starting wpa_supplicant. At this point i cant get any connection to my AP. The only way is to reload cfg80211 mac80211 ath9k. After the reload he connects my outomatically to my AP without starting the /etc/init.d/net.wlan0 start script.
I have also patched the /usr/src/compat-wireless-2009-02-16/net/wireless/reg.c file with the same-hint.patch
what to do next???
The patch has not changed the need of reloading cfg80211 mac80211 and ath9k after boot if i want use my LinksysWMP300Nv2.
Udev:/lib/udev/rules.d/85-regulatory.rules
the location seems to be ok.
but at boot of my system he never loads the second part of the frequences when cfg80211 loads.
Well evening from Vienna
Alexander Bartha
Signature · 1 line
Psssst! Schon vom neuen GMX MultiMessenger geh?rt? Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger01
Quoted 5 lines · Alexander Bartha
Hello Luis,
i have rebuild compat-wireless with
CONFIG_ATH9K_DEBUG=yin config.mk then -- make unload -- modprobe ath9k debug=0x00000080 -- iw list-- (Output)
You forgot to provide the kernel log when loading ath9k with debug.
Luis
Hello Luis
i have no kernel.log. All my attemps to get a kernel.log or kern.log with syslog-ng where in vain. Mhhh???? Here is a list of my logfiles in /var/log/ Directory:
cups/ kdm.log messages.3.gz syslog dmesg lastlog messages.4.gz uucp.log emerge-fetch.log mail.err mysql/ wtmp emerge.log maillog news/ wtmp.1.gz faillog mail.log portage/ xdm.log gdm/ messages rc.log Xorg.0.log genkernel.log messages.1.gz samba/ Xorg.0.log.old HOSTS/ messages.2.gz sandbox/
So how i can debug ath9k or get the debug messages????
Well day
Alexander Bartha
-------- Original-Nachricht --------
Quoted 17 lines
Datum: Mon, 16 Feb 2009 13:42:10 -0800
Von: "Luis R. Rodriguez" <[email protected]>
An: Alexander Bartha <[email protected]>
CC: ath9k-devel at lists.ath9k.org, Luis.Rodriguez at atheros.com
Betreff: Re: [ath9k-devel] ath9k WMP300nv2 (AR5416)Quoted 5 lines · Alexander Bartha
Hello Luis,
i have rebuild compat-wireless with
CONFIG_ATH9K_DEBUG=yin config.mk then -- make unload -- modprobe ath9k debug=0x00000080 -- iw list-- (Output)You forgot to provide the kernel log when loading ath9k with debug.
Luis
Signature · 2 lines
Jetzt 1 Monat kostenlos! GMX FreeDSL - Telefonanschluss + DSL f?r nur 17,95 Euro/mtl.!* http://dsl.gmx.de/?ac=OM.AD.PD003K11308T4569a
Hello Luis
i have no kernel.log. All my attemps to get a kernel.log or kern.log with syslog-ng where in vain. Mhhh???? Here is a list of my logfiles in /var/log/ Directory:
cups/ kdm.log messages.3.gz syslog dmesg lastlog messages.4.gz uucp.log emerge-fetch.log mail.err mysql/ wtmp emerge.log maillog news/ wtmp.1.gz faillog mail.log portage/ xdm.log gdm/ messages rc.log Xorg.0.log genkernel.log messages.1.gz samba/ Xorg.0.log.old HOSTS/ messages.2.gz sandbox/
So how i can debug ath9k or get the debug messages????
Well day
-------- Original-Nachricht --------
Quoted 17 lines
Datum: Mon, 16 Feb 2009 13:42:10 -0800
Von: "Luis R. Rodriguez" <[email protected]>
An: Alexander Bartha <[email protected]>
CC: ath9k-devel at lists.ath9k.org, Luis.Rodriguez at atheros.com
Betreff: Re: [ath9k-devel] ath9k WMP300nv2 (AR5416)Quoted 5 lines · Alexander Bartha
Hello Luis,
i have rebuild compat-wireless with
CONFIG_ATH9K_DEBUG=yin config.mk then -- make unload -- modprobe ath9k debug=0x00000080 -- iw list-- (Output)You forgot to provide the kernel log when loading ath9k with debug.
Luis
Signature · 1 line
Psssst! Schon vom neuen GMX MultiMessenger geh?rt? Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger01
Quoted 12 lines · Alexander Bartha
Hello Luis
i have no kernel.log. All my attemps to get a kernel.log or kern.log with syslog-ng where in vain. Mhhh???? Here is a list of my logfiles in/var/log/Directory:cups/ kdm.log messages.3.gz syslog dmesg lastlog messages.4.gz uucp.log emerge-fetch.log mail.err mysql/ wtmp emerge.log maillog news/ wtmp.1.gz faillog mail.log portage/ xdm.log gdm/ messages rc.log Xorg.0.log genkernel.log messages.1.gz samba/ Xorg.0.log.old HOSTS/ messages.2.gz sandbox/
Quoted 1 line
So how i can debug ath9k or get the debug messages????
Kernel log is shown by the dmesg command. The kernel has a certain amount of memory for the log, so only older messages are not shown once the memory is exhausted. However, it's normally enough memory to hold the full log from the boot time.
Kernel messages are normally logged to /var/log/messages, but the debug messages may be omitted. The kernel messages during the boot are preserved in /var/log/dmesg until the next reboot.
Signature · 2 lines
Regards, Pavel Roskin
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
In reply to Luis R. RodriguezHello to everybody at linuxwireless
Since the "Submodule" ath comes aht9k says in messages:
May 7 22:11:34 ws1 [ 4442.304763] ath9k: Unable to set channel May 7 22:11:34 ws1 [ 4442.425550] ath9k: timeout (100000 us) on reg 0x9860: 0x0 0049d19 & 0x00000001 != 0x00000000 May 7 22:11:34 ws1 [ 4442.425555] ath9k: Unable to reset channel (2422 Mhz) res et status 4294967291 May 7 22:11:34 ws1 [ 4442.425560] ath9k: Unable to set channel May 7 22:11:34 ws1 [ 4442.546365] ath9k: timeout (100000 us) on reg 0x9860: 0x0
0049d19 & 0x00000001 != 0x00000000
i have tried different versions of the modules but since compat-wireless-2009-04-16 i get this errors.
till that all works fine sometime the driver have little problems after not using the network. thanks for the drivers
well evening from vienna
Alexander Bartha
Signature · 1 line
Neu: GMX FreeDSL Komplettanschluss mit DSL 6.000 Flatrate + Telefonanschluss f?r nur 17,95 Euro/mtl.!* http://dslspecial.gmx.de/freedsl-surfflat/?ac=OM.AD.PD003K11308T4569a
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 11 lines · Alexander Bartha
Hello to everybody at linuxwireless
Since the "Submodule" ath comes aht9k says in messages:
May 7 22:11:34 ws1 [ 4442.304763] ath9k: Unable to set channel May 7 22:11:34 ws1 [ 4442.425550] ath9k: timeout (100000 us) on reg 0x9860: 0x0 0049d19 & 0x00000001 != 0x00000000 May 7 22:11:34 ws1 [ 4442.425555] ath9k: Unable to reset channel (2422 Mhz) res et status 4294967291 May 7 22:11:34 ws1 [ 4442.425560] ath9k: Unable to set channel May 7 22:11:34 ws1 [ 4442.546365] ath9k: timeout (100000 us) on reg 0x9860: 0x0
Quoted 5 lines
0049d19 &
0x00000001!=0x00000000i have tried different versions of the modules but since compat-wireless-2009-04-16 i get this errors.
till that all works fine sometime the driver have little problems after not using the network. thanks for the drivers
I track wireless-testing.git and I saw it in the last weeks. I think it happens after about 260 pings at the normal speed (i.e. not with flood ping). I was thinking about bisecting the problem, but I don't have much time right now.
Last time I saw it was on Monday. There were some changes to ath9k since then, so maybe it's fixed.
Signature · 2 lines
Regards, Pavel Roskin
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 18 lines · Pavel Roskin
Quoted 13 lines · Alexander Bartha
Hello to everybody at linuxwireless
Since the "Submodule" ath comes aht9k says in messages:
May ?7 22:11:34 ws1 [ 4442.304763] ath9k: Unable to set channel
May ?7 22:11:34 ws1 [ 4442.425550] ath9k: timeout (100000 us) on reg0x9860:0x00049d19 &0x00000001!=0x00000000
May ?7 22:11:34 ws1 [ 4442.425555] ath9k: Unable to reset channel (2422 Mhz) res et status 4294967291
May ?7 22:11:34 ws1 [ 4442.425560] ath9k: Unable to set channel
May ?7 22:11:34 ws1 [ 4442.546365] ath9k: timeout (100000 us) on reg0x9860:0x00049d19 &0x00000001!=0x00000000Quoted 3 lines
i have tried different versions of the modules but since compat-wireless-2009-04-16 i get this errors.
till that all works fine sometime the driver have little problems after not using the network. thanks for the drivers
Quoted 7 lines
I track wireless-testing.git and I saw it in the last weeks. ?I think it happens after about 260 pings at the normal speed (i.e. not with flood ping). ?I was thinking about bisecting the problem, but I don't have much time right now.
Last time I saw it was on Monday. ?There were some changes to ath9k since then, so maybe it's fixed.
This may have been caused by the idle patches for which Johannes has posted a fix. This should get merged soon so give it a few more days and try again.
If you want something a little more stable you can go with the stable compat-wireless releases:
http://wireless.kernel.org/en/users/Download/stable
Luis
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 6 lines · Luis R. Rodriguez
Quoted 5 lines · Pavel Roskin
Quoted 4 lines · Alexander Bartha
Hello to everybody at linuxwireless
Since the "Submodule" ath comes aht9k says in messages:
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
May ?7 22:11:34 ws1 [ 4442.304763] ath9k: Unable to set channel
May ?7 22:11:34 ws1 [ 4442.425550] ath9k: timeout (100000 us) on reg0x9860:0x00049d19 &0x00000001!=0x00000000
May ?7 22:11:34 ws1 [ 4442.425555] ath9k: Unable to reset channel (2422 Mhz) res et status 4294967291
May ?7 22:11:34 ws1 [ 4442.425560] ath9k: Unable to set channel
May ?7 22:11:34 ws1 [ 4442.546365] ath9k: timeout (100000 us) on reg0x9860:0x00049d19 &0x00000001!=0x00000000
I can reproduce, and I tried without the idle patches but I still see the issue. I see this issue only after suspend. Did you suspend and get this as well? I see this using AR5416. If you are seeing this on suspend can you try with the patch I posted to linux-wireless to see if it helps a little?
Luis
Quoted 23 lines
Quoted 11 lines
Quoted 3 lines
i have tried different versions of the modules but since compat-wireless-2009-04-16 i get this errors.
till that all works fine sometime the driver have little problems after not using the network. thanks for the drivers
I track wireless-testing.git and I saw it in the last weeks. ?I think it happens after about 260 pings at the normal speed (i.e. not with flood ping). ?I was thinking about bisecting the problem, but I don't have much time right now.
Last time I saw it was on Monday. ?There were some changes to ath9k since then, so maybe it's fixed.
This may have been caused by the idle patches for which Johannes has posted a fix. This should get merged soon so give it a few more days and try again.
If you want something a little more stable you can go with the stable compat-wireless releases:
http://wireless.kernel.org/en/users/Download/stable
?Luis
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoting "Luis R. Rodriguez" <[email protected]>:
Quoted 5 lines
I can reproduce, and I tried without the idle patches but I still see the issue. I see this issue only after suspend. Did you suspend and get this as well? I see this using AR5416. If you are seeing this on suspend can you try with the patch I posted to linux-wireless to see if it helps a little?
I saw this on AR9280 without any suspends. The card doesn't support the 802.11a range, so it's not a direct equivalent of the problem I bisected with ath5k (invalid rates when scanning and transmitting).
Signature · 2 lines
Regards, Pavel Roskin
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 11 lines · Pavel Roskin
Quoting "Luis R. Rodriguez" <[email protected]>:
Quoted 5 lines
I can reproduce, and I tried without the idle patches but I still see the issue. I see this issue only after suspend. Did you suspend and get this as well? I see this using AR5416. If you are seeing this on suspend can you try with the patch I posted to linux-wireless to see if it helps a little?
I saw this on AR9280 without any suspends. ?The card doesn't support the 802.11a range, so it's not a direct equivalent of the problem I bisected with ath5k (invalid rates when scanning and transmitting).
Thanks for the heads up Pavel. So can you guys test with this option set as follows:
CONFIG_MAC80211_DEFAULT_PS_VALUE=0
If using compat-wireless just stuff it into config.mk.
This fixes my issues and points towards PS code. This could be how we handle PS in ath9k (more likely) or mac80211. For now please disable this if using ath9k until we figure out what causes this.
Luis
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 16 lines · Luis R. Rodriguez
Quoted 11 lines · Pavel Roskin
Quoting "Luis R. Rodriguez" <[email protected]>:
Quoted 5 lines
I can reproduce, and I tried without the idle patches but I still see the issue. I see this issue only after suspend. Did you suspend and get this as well? I see this using AR5416. If you are seeing this on suspend can you try with the patch I posted to linux-wireless to see if it helps a little?
I saw this on AR9280 without any suspends. The card doesn't support the 802.11a range, so it's not a direct equivalent of the problem I bisected with ath5k (invalid rates when scanning and transmitting).
Thanks for the heads up Pavel. So can you guys test with this option set as follows:
Quoted 7 lines
CONFIG_MAC80211_DEFAULT_PS_VALUE=0If using compat-wireless just stuff it into config.mk.
This fixes my issues and points towards PS code. This could be how we handle PS in ath9k (more likely) or mac80211. For now please disable this if using ath9k until we figure out what causes this.
It looks like there are two issues, and I confused them. One is characterized by the kernel messages about the channel, the one originally reported in this thread. I have seen it, but I don't remember the exact circumstances.
Another issue is connection loss to a WPA enabled AP after several minutes. That's what I have seen with AR9280. iwconfig still shows an association, but no traffic can flow.
I just want to tell that it's two different issues. The later is much more critical for me, but it would take about 15 minutes to verify every step if bisecting. Unfortunately, I don't have time to bisect it now, but maybe I'll do it later during this week.
Signature · 2 lines
Regards, Pavel Roskin
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 30 lines · Pavel Roskin
Quoted 16 lines · Luis R. Rodriguez
Quoted 11 lines · Pavel Roskin
Quoting "Luis R. Rodriguez" <[email protected]>:
Quoted 5 lines
I can reproduce, and I tried without the idle patches but I still see the issue. I see this issue only after suspend. Did you suspend and get this as well? I see this using AR5416. If you are seeing this on suspend can you try with the patch I posted to linux-wireless to see if it helps a little?
I saw this on AR9280 without any suspends. ?The card doesn't support the 802.11a range, so it's not a direct equivalent of the problem I bisected with ath5k (invalid rates when scanning and transmitting).
Thanks for the heads up Pavel. So can you guys test with this option set as follows:
Quoted 7 lines
CONFIG_MAC80211_DEFAULT_PS_VALUE=0If using compat-wireless just stuff it into config.mk.
This fixes my issues and points towards PS code. This could be how we handle PS in ath9k (more likely) or mac80211. For now please disable this if using ath9k until we figure out what causes this.
It looks like there are two issues, and I confused them. ?One is characterized by the kernel messages about the channel, the one originally reported in this thread. ?I have seen it, but I don't remember the exact circumstances.
Quoted 8 lines
Another issue is connection loss to a WPA enabled AP after several minutes. ?That's what I have seen with AR9280. ?iwconfig still shows an association, but no traffic can flow.
I just want to tell that it's two different issues. ?The later is much more critical for me, but it would take about 15 minutes to verify every step if bisecting. ?Unfortunately, I don't have time to bisect it now, but maybe I'll do it later during this week.
Thanks for the heads up, lets address this in another thread then.
Luis
[ath9k-devel] Antwort: Re: ath9k module-Unable to set channel-since ath comes
In reply to Luis R. RodriguezHello to linuxwireless
thanks for response. The stabel compat-wireless-2.6.30-rc4.tar.bz2 release works well. The bleeding edge compat-wireless works to but only till the new submodule ath comes in live (compat-wireless-2009-04-12.tar.bz2 is the last version which i have tasted and which works well).
well day from vienna
Alexander Bartha
Abteilungsleiter NOC (EDV) und OnlineVerkauf
Tel.: +43 1 982 16 48 304
Fax: +43 1 982 16 48 18
E-Mail: alexander.bartha at drz-wien.at
Die Wiener Volkshochschulen GmbH
Projekt DRZ-Wien
Vogtgasse 29
1140 Wien
UID - ATU 63945413
"Luis R. Rodriguez" <[email protected]>
10.05.2009 20:41
An
Pavel Roskin <[email protected]>
Kopie
Alexander Bartha <[email protected]>, ath9k-devel at lists.ath9k.org, linux-wireless <[email protected]>
Thema
Re: [ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 8 lines · Luis R. Rodriguez
Quoted 7 lines · Pavel Roskin
Quoted 6 lines · Alexander Bartha
Hello to everybody at linuxwireless
Since the "Submodule" ath comes aht9k says in messages:
May 7 22:11:34 ws1 [ 4442.304763] ath9k: Unable to set channel May 7 22:11:34 ws1 [ 4442.425550] ath9k: timeout (100000 us) on reg
0x9860: 0x0
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
0049d19 &
0x00000001!=0x00000000May 7 22:11:34 ws1 [ 4442.425555] ath9k: Unable to reset channel
(2422 Mhz) res
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
et status 4294967291
May 7 22:11:34 ws1 [ 4442.425560] ath9k: Unable to set channel May 7 22:11:34 ws1 [ 4442.546365] ath9k: timeout (100000 us) on reg
0x9860: 0x0
Quoted 1 line
Quoted 1 line
Quoted 1 line
0049d19 &
0x00000001!=0x00000000
I can reproduce, and I tried without the idle patches but I still see the issue. I see this issue only after suspend. Did you suspend and get this as well? I see this using AR5416. If you are seeing this on suspend can you try with the patch I posted to linux-wireless to see if it helps a little?
Luis
Quoted 1 line
Quoted 1 line
Quoted 1 line
i have tried different versions of the modules but since
compat-wireless-2009-04-16 i get this errors.
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
till that all works fine sometime the driver have little problems
after not using the network. thanks for the drivers
Quoted 2 lines
Quoted 2 lines
I track wireless-testing.git and I saw it in the last weeks. I think
it
Quoted 11 lines
Quoted 6 lines
happens after about 260 pings at the normal speed (i.e. not with flood ping). I was thinking about bisecting the problem, but I don't have much time right now.
Last time I saw it was on Monday. There were some changes to ath9k since then, so maybe it's fixed.
This may have been caused by the idle patches for which Johannes has posted a fix. This should get merged soon so give it a few more days and try again.
Quoted 7 lines
If you want something a little more stable you can go with the stable compat-wireless releases:
http://wireless.kernel.org/en/users/Download/stable
Luis
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.ath9k.org/pipermail/ath9k-devel/attachments/20090512/59a16be9/attachment.htm
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 7 lines · On Mon, May 11, 2009 at 11:38 PM, <[email protected]> wrote:
Hello to linuxwireless
thanks for response. The stabel compat-wireless-2.6.30-rc4.tar.bz2 release works well. The bleeding edge compat-wireless works to but only till the new submodule ath comes in live (compat-wireless-2009-04-12.tar.bz2 is the last version which i have tasted and which works well).
I've tested this and its not the "ath" module which introduces an issue its a patch which enables PS by default. You can disable that by recompiling with:
CONFIG_MAC80211_DEFAULT_PS_VALUE=0
If using compat-wireless just stuff it into config.mk.
Luis
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 7 lines · Luis R. Rodriguez
I've tested this and its not the "ath" module which introduces an issue its a patch which enables PS by default. You can disable that by recompiling with:
CONFIG_MAC80211_DEFAULT_PS_VALUE=0If using compat-wireless just stuff it into config.mk.
I object to that assertion, or at least this way of putting it.
If powersave by default causes issues then it's not my patch that's causing the problem, it's the fact that ath9k can't properly deal with powersave in this case. Had the user enabled powersave manually they would have run into the same issue. As such, I think ath9k should probably simply stop claiming it can support PS.
johannes
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 801 bytes
Desc: This is a digitally signed message part
Url : http://lists.ath9k.org/pipermail/ath9k-devel/attachments/20090512/8d34fde5/attachment.pgp
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 10 lines · Johannes Berg
Quoted 7 lines · Luis R. Rodriguez
I've tested this and its not the "ath" module which introduces an issue its a patch which enables PS by default. You can disable that by recompiling with:
CONFIG_MAC80211_DEFAULT_PS_VALUE=0If using compat-wireless just stuff it into config.mk.
Quoted 7 lines
I object to that assertion, or at least this way of putting it.
If powersave by default causes issues then it's not my patch that's causing the problem, it's the fact that ath9k can't properly deal with powersave in this case. Had the user enabled powersave manually they would have run into the same issue. As such, I think ath9k should probably simply stop claiming it can support PS.
Heh yes, what I meant was ath9k's PS support has some issues which still need to be resolved (at least as I've tested it).
Luis
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Hi,
Quoted 14 lines · Luis R. Rodriguez
Quoted 12 lines · Johannes Berg
Quoted 7 lines · Luis R. Rodriguez
I've tested this and its not the "ath" module which introduces an issue its a patch which enables PS by default. You can disable that by recompiling with:
CONFIG_MAC80211_DEFAULT_PS_VALUE=0If using compat-wireless just stuff it into config.mk.
I object to that assertion, or at least this way of putting it.
Quoted 9 lines
Quoted 5 lines
If powersave by default causes issues then it's not my patch that's causing the problem, it's the fact that ath9k can't properly deal with powersave in this case. Had the user enabled powersave manually they would have run into the same issue. As such, I think ath9k should probably simply stop claiming it can support PS.
Heh yes, what I meant was ath9k's PS support has some issues which still need to be resolved (at least as I've tested it).
I've already reported ath9k's issues with PS multiple times [1] [2] [3], but the driver hasn't been fixed yet. You can find a verbose debugging output at [4], I hope that helps in fixing the problem (I can provide even more info if needed and I'm willing to test patches).
Anyway, if the issue isn't going to be resolved quickly (e.g. before Johannes' "enable PS by default" patch lands in mainline), I think it's better to disable PS in ath9k as previously suggested.
Regards,
Davide
[1] http://marc.info/?l=linux-wireless&m=123816406913599&w=2
[2] http://marc.info/?l=linux-wireless&m=123999864507104&w=2
[3] http://marc.info/?l=linux-wireless&m=124025926613089&w=2
[4] http://marc.info/?l=linux-wireless&m=124026772102023&w=2
[ath9k-devel] Where can I buy a wifi card supported by ath9k?
List,
I like to buy a wifi card supported by ath9k but do not know which card on market is good one.
Thanks for any help.
---henry
[ath9k-devel] Where can I buy a wifi card supported by ath9k?
Quoted 5 lines · hong zhang
List,
I like to buy a wifi card supported by ath9k but do not know which card on market is good one.
Luis
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
In reply to Davide PesaventoQuoted 4 lines · Davide Pesavento
I've already reported ath9k's issues with PS multiple times [1] [2] [3], but the driver hasn't been fixed yet. You can find a verbose debugging output at [4], I hope that helps in fixing the problem (I can provide even more info if needed and I'm willing to test patches).
I submitted a set of patches to resolve some of the PS issues in ath9k. I would expect these to hit wireless-testing.git eventually, but if you are willing to test the changes before that, you can find the patches from http://w1.fi/p/ps/
One thing to note here is that there are still some issues with the timeout=0 case (use of PS-Poll to fetch buffered frames) which is enabled with "iwconfig wlan0 power on", so at this point, I would recommend running the test either with the default wireless-testing.git PS mode setting or by enabling power saving with "iwconfig wlan0 power timeout 500ms" which should result in the same configuration.
I have not tested these on AR5418, but at least with AR9280, these patches do improve stability and general functionality of the default PS mode considerably. I have been able to run multi-hour tests without losing connection.
- Jouni
[ath9k-devel] ath9k module-Unable to set channel-since ath comes
Quoted 11 lines · Jouni Malinen
Quoted 4 lines · Davide Pesavento
I've already reported ath9k's issues with PS multiple times [1] [2] [3], but the driver hasn't been fixed yet. You can find a verbose debugging output at [4], I hope that helps in fixing the problem (I can provide even more info if needed and I'm willing to test patches).
I submitted a set of patches to resolve some of the PS issues in ath9k. I would expect these to hit wireless-testing.git eventually, but if you are willing to test the changes before that, you can find the patches from http://w1.fi/p/ps/
Quoted 6 lines
One thing to note here is that there are still some issues with the timeout=0 case (use of PS-Poll to fetch buffered frames) which is enabled with "iwconfig wlan0 power on", so at this point, I would recommend running the test either with the default wireless-testing.git PS mode setting or by enabling power saving with "iwconfig wlan0 power timeout 500ms" which should result in the same configuration.
Most probably that's because mac80211 does not disable power save mode when sending PS-Poll frames. So stlc45xx does not require disable of PSM but then again ath9k requires it, we need to solve this somehow.
I have been thinking about separating power save mode and firmware wakeup/sleep modes from each other in mac80211 API. To me it looks like ath9k does more like firmware wakeup/sleep when power save mode is changing. But this is just a wild idea, I have no idea if it's practical or not.
Signature · 1 line
Kalle Valo
[ath9k-devel] Antwort: Re: ath9k module-Unable to set channel-since ath comes
In reply to Jouni MalinenHello to Linuxwireless
at the last weekend i tried again with compat-wireless-2009-15-05 and i have disabled the PS (this value "CONFIG_MAC80211_DEFAULT_PS_VALUE=0" and "CONFIG_MAC80211_DEFAULT_PS=n") in config.mk but nothing changed. After 2 or 3 minutes i sawed again the "unable to set channel" in /var/log/messages.
Well day from vienna
Alexander Bartha
Abteilungsleiter NOC (EDV) und OnlineVerkauf
Tel.: +43 1 982 16 48 304
Fax: +43 1 982 16 48 18
E-Mail: alexander.bartha at drz-wien.at
Die Wiener Volkshochschulen GmbH
Projekt DRZ-Wien
Vogtgasse 29
1140 Wien
UID - ATU 63945413
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.ath9k.org/pipermail/ath9k-devel/attachments/20090519/6ecba248/attachment.htm