omap3 evm: MMC switch support
Subsystems (3)
Update OMAP3 EVM board support to support the MMC/SD switches, when used with the twl4030 based power card.
Also, less usefully, LEDB as a GPIO LED ... it's on the underside of the board, so it's probably not very useful to most folk. The LCD backlight is controlled by LEDA though; more useful, though its PWM mode might not be practical on this board (I don't know how that inductor will affect things).
This is done from schematics, so it needs testing (and maybe some bugfixes) from folk with an EVM board.
- Dave
--- arch/arm/mach-omap2/board-omap3evm.c | 69 ++++++++++++++++++++++++++------ arch/arm/mach-omap2/mux.c | 2 arch/arm/plat-omap/include/mach/mux.h | 1 3 files changed, 61 insertions(+), 11 deletions(-)
arch/arm/mach-omap2/board-omap3evm.c +58 -11
@@ -19,6 +19,7 @@#include <linux/err.h> #include <linux/clk.h> #include <linux/input.h> +#include <linux/leds.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h>
@@ -31,6 +32,7 @@#include <mach/gpio.h> #include <mach/board.h> +#include <mach/mux.h> #include <mach/usb-musb.h> #include <mach/usb-ehci.h> #include <mach/common.h>
@@ -88,10 +90,66 @@ static struct omap_uart_config omap3_evm .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; +static struct twl4030_hsmmc_info mmc[] = { + { + .mmc =1 , + .wires =4 , + .gpio_cd = -EINVAL , + .gpio_wp =63 , + }, + {}/* Terminator */ +}; + +static struct gpio_led gpio_leds[] = { + { + .name ="omap3evm::ledb" , +/* normally not visible (board underside) */ + .default_trigger ="default-on" , + .gpio = -EINVAL ,/* gets replaced */ + .active_low = true, + }, +}; + +static struct gpio_led_platform_data gpio_led_info = { + .leds = gpio_leds, + .num_leds =ARRAY_SIZE (gpio_leds), +}; + +static struct platform_device leds_gpio = { + .name ="leds-gpio" , + .id =-1 , + .dev = { + .platform_data = &gpio_led_info, + }, +}; + + +static int omap3evm_twl_gpio_setup (struct device *dev, +unsigned gpio,unsigned ngpio) +{ +/* gpio + 0 is "mmc0_cd" (input/IRQ) */ +omap_cfg_reg (L8_34XX_GPIO63 ); + mmc[0 ].gpio_cd = gpio +0 ; +twl4030_mmc_init (mmc); + +/* Most GPIOs are for USB OTG. Some are mostly sent to +* the P2 connector; notably LEDA for the LCD backlight. +*/ + +/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */ + gpio_leds[2 ].gpio = gpio +TWL4030_GPIO_MAX +1 ; + +platform_device_register (&leds_gpio); + +return 0 ; +} +static struct twl4030_gpio_platform_data omap3evm_gpio_data = { .gpio_base =OMAP_MAX_GPIO_LINES , .irq_base =TWL4030_GPIO_IRQ_BASE , .irq_end =TWL4030_GPIO_IRQ_END , + .use_leds = true, + .setup = omap3evm_twl_gpio_setup, };static struct twl4030_usb_data omap3evm_usb_data = {
@@ -232,16 +290,6 @@ static struct platform_device *omap3_evm &omap3evm_smc911x_device, }; -static struct twl4030_hsmmc_info mmc[]__initdata = { - { - .mmc =1 , - .wires =4 , - .gpio_cd = -EINVAL , - .gpio_wp = -EINVAL , - }, - {}/* Terminator */ -}; -static void __init omap3_evm_init (void ) {omap3_evm_i2c_init ();
@@ -254,7 +302,6 @@ static void __init omap3_evm_init(void) ARRAY_SIZE(omap3evm_spi_board_info));omap_serial_init (); -twl4030_mmc_init (mmc);usb_musb_init ();usb_ehci_init ();omap3evm_flash_init ();
arch/arm/mach-omap2/mux.c +2 -0
@@ -463,6 +463,8 @@ MUX_CFG_34XX("AF26_34XX_GPIO0", 0x1e0, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) MUX_CFG_34XX("AF22_34XX_GPIO9", 0xa18, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) +MUX_CFG_34XX("L8_34XX_GPIO63", 0x0ce, + OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) MUX_CFG_34XX("AF6_34XX_GPIO140_UP", 0x16c, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP) MUX_CFG_34XX("AE6_34XX_GPIO141", 0x16e,
arch/arm/plat-omap/include/mach/mux.h +1 -0
@@ -792,6 +792,7 @@ enum omap34xx_index {J25_34XX_GPIO170 ,AF26_34XX_GPIO0 ,AF22_34XX_GPIO9 , +L8_34XX_GPIO63 ,AF6_34XX_GPIO140_UP ,AE6_34XX_GPIO141 , AF5_34XX_GPIO142,
Hi ,
I tested the patch on the OMAP 3 EVM. I still find that the hotplug feature does not work on the OMAP3 EVM. The issue is that if I read the gpio_cd, I am getting the correct value on the gpio pin(INSERT = 0, PLUGOUT = 1) but the interrupts are not generated.
The mmc0 interrupts always shows 0.
[email protected]:~# cat /proc/interrupts CPU0 11: 0 INTC prcm 12: 4 INTC DMA 25: 0 INTC dispc 37: 1724 INTC gp timer 56: 267 INTC i2c_omap 57: 0 INTC i2c_omap 61: 0 INTC i2c_omap 72: 178 INTC serial idle, serial 73: 1 INTC serial idle 74: 1 INTC serial idle 83: 43 INTC mmc0 92: 0 INTC musb_hdrc 93: 0 INTC musb_hdrc 335: 0 GPIO ads7846 336: 3565 GPIO eth0 369: 0 twl4030 twl4030_keypad 378: 0 twl4030 twl4030_usb 384: 0 twl4030 mmc0 Err: 0
Regards
Mani
Quoted 162 lines
-----Original Message-----
From: [email protected] [mailto:linux-omap- [email protected]] On Behalf Of David Brownell
Sent: Thursday, February 05, 2009 4:53 AM
To: OMAP
Subject: [patch/rft 2.6.29-rc3-omap-git] omap3 evm: MMC switch supportUpdate OMAP3 EVM board support to support the MMC/SD switches, when used with the twl4030 based power card.
Also, less usefully, LEDB as a GPIO LED ... it's on the underside of the board, so it's probably not very useful to most folk. The LCD backlight is controlled by LEDA though; more useful, though its PWM mode might not be practical on this board (I don't know how that inductor will affect things).
This is done from schematics, so it needs testing (and maybe some bugfixes) from folk with an EVM board.
- Dave
--- arch/arm/mach-omap2/board-omap3evm.c | 69 ++++++++++++++++++++++++++------ arch/arm/mach-omap2/mux.c | 2 arch/arm/plat-omap/include/mach/mux.h | 1 3 files changed, 61 insertions(+), 11 deletions(-)arch/arm/mach-omap2/board-omap3evm.c +58
-11@@ -19,6 +19,7 @@#include <linux/err.h> #include <linux/clk.h> #include <linux/input.h> +#include <linux/leds.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> @@ -31,6 +32,7 @@#include <mach/gpio.h> #include <mach/board.h> +#include <mach/mux.h> #include <mach/usb-musb.h> #include <mach/usb-ehci.h> #include <mach/common.h> @@ -88,10 +90,66 @@ static struct omap_uart_config omap3_evm .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; +static struct twl4030_hsmmc_info mmc[] = { + { + .mmc =1 , + .wires =4 , + .gpio_cd = -EINVAL , + .gpio_wp =63 , + }, + {}/* Terminator */ +}; + +static struct gpio_led gpio_leds[] = { + { + .name ="omap3evm::ledb" , +/* normally not visible (board underside) */ + .default_trigger ="default-on" , + .gpio = -EINVAL ,/* gets replaced */ + .active_low = true, + }, +}; + +static struct gpio_led_platform_data gpio_led_info = { + .leds = gpio_leds, + .num_leds =ARRAY_SIZE (gpio_leds), +}; + +static struct platform_device leds_gpio = { + .name ="leds-gpio" , + .id =-1 , + .dev = { + .platform_data = &gpio_led_info, + }, +}; + + +static int omap3evm_twl_gpio_setup (struct device *dev, +unsigned gpio,unsigned ngpio) +{ +/* gpio + 0 is "mmc0_cd" (input/IRQ) */ +omap_cfg_reg (L8_34XX_GPIO63 ); + mmc[0 ].gpio_cd = gpio +0 ; +twl4030_mmc_init (mmc); + +/* Most GPIOs are for USB OTG. Some are mostly sent to +* the P2 connector; notably LEDA for the LCD backlight. +*/ + +/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */ + gpio_leds[2 ].gpio = gpio +TWL4030_GPIO_MAX +1 ; + +platform_device_register (&leds_gpio); + +return 0 ; +} +static struct twl4030_gpio_platform_data omap3evm_gpio_data = { .gpio_base =OMAP_MAX_GPIO_LINES , .irq_base =TWL4030_GPIO_IRQ_BASE , .irq_end =TWL4030_GPIO_IRQ_END , + .use_leds = true, + .setup = omap3evm_twl_gpio_setup, };static struct twl4030_usb_data omap3evm_usb_data = {@@ -232,16 +290,6 @@ static struct platform_device *omap3_evm &omap3evm_smc911x_device, }; -static struct twl4030_hsmmc_info mmc[]__initdata = { - { - .mmc =1 , - .wires =4 , - .gpio_cd = -EINVAL , - .gpio_wp = -EINVAL , - }, - {}/* Terminator */ -}; -static void __init omap3_evm_init (void ) {omap3_evm_i2c_init ();@@ -254,7 +302,6 @@ static void __init omap3_evm_init(void) ARRAY_SIZE(omap3evm_spi_board_info));omap_serial_init (); -twl4030_mmc_init (mmc);usb_musb_init ();usb_ehci_init ();omap3evm_flash_init ();arch/arm/mach-omap2/mux.c +2
-0@@ -463,6 +463,8 @@ MUX_CFG_34XX("AF26_34XX_GPIO0", 0x1e0, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) MUX_CFG_34XX("AF22_34XX_GPIO9", 0xa18, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) +MUX_CFG_34XX("L8_34XX_GPIO63", 0x0ce, + OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) MUX_CFG_34XX("AF6_34XX_GPIO140_UP", 0x16c, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT_PULLUP) MUX_CFG_34XX("AE6_34XX_GPIO141", 0x16e,arch/arm/plat-omap/include/mach/mux.h +1
-1@@ -792,6 +792,7 @@ enum omap34xx_index {J25_34XX_GPIO170 ,AF26_34XX_GPIO0 ,AF22_34XX_GPIO9 , +L8_34XX_GPIO63 ,AF6_34XX_GPIO140_UP ,AE6_34XX_GPIO141 , AF5_34XX_GPIO142, --To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 7 lines · Manikandan
I tested the patch on the OMAP 3 EVM. I still find that the hotplug feature does not work on the OMAP3 EVM. The issue is that if I read the
gpio_cd, I am getting the correct value on the gpiopin(INSERT = 0, PLUGOUT = 1)but the interrupts are not generated.The mmc0 interrupts always shows 0.
Are you getting any other IRQs through the twl4030 code?
There's not a lot of debugging I can do with this, since I don't have an EVM ... and since this seems to work OK on other boards. (Testing on SDP being easiest, since it's got a slot not tied down with MMC root.)
This patch was basically sent as a seed, since nobody else seemed to be filling in the missing MMC/SD pieces on that board.
- Dave
Quoted 22 lines
[email protected]:~# cat /proc/interrupts CPU0 11: 0 INTC prcm 12: 4 INTC DMA 25: 0 INTC dispc 37: 1724 INTC gp timer 56: 267 INTC i2c_omap 57: 0 INTC i2c_omap 61: 0 INTC i2c_omap 72: 178 INTC serial idle, serial 73: 1 INTC serial idle 74: 1 INTC serial idle 83: 43 INTC mmc0 92: 0 INTC musb_hdrc 93: 0 INTC musb_hdrc 335: 0 GPIO ads7846 336: 3565 GPIO eth0 369: 0 twl4030 twl4030_keypad 378: 0 twl4030 twl4030_usb 384: 0 twl4030 mmc0 Err: 0
Quoted 22 lines
Regards
ManiQuoted 19 lines
-----Original Message-----
From: [email protected] [mailto:linux-omap- [email protected]] On Behalf Of David Brownell
Sent: Thursday, February 05, 2009 4:53 AM
To: OMAP
Subject: [patch/rft 2.6.29-rc3-omap-git] omap3 evm: MMC switch supportUpdate OMAP3 EVM board support to support the MMC/SD switches, when used with the twl4030 based power card.
Also, less usefully, LEDB as a GPIO LED ... it's on the underside of the board, so it's probably not very useful to most folk. The LCD backlight is controlled by LEDA though; more useful, though its PWM mode might not be practical on this board (I don't know how that inductor will affect things).
This is done from schematics, so it needs testing (and maybe some bugfixes) from folk with an EVM board.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Tony Lindgren
maintainerQuoted 11 lines · David Brownell
Quoted 7 lines · Manikandan
I tested the patch on the OMAP 3 EVM. I still find that the hotplug feature does not work on the OMAP3 EVM. The issue is that if I read the
gpio_cd, I am getting the correct value on the gpiopin(INSERT = 0, PLUGOUT = 1)but the interrupts are not generated.The mmc0 interrupts always shows 0.
Are you getting any other IRQs through the twl4030 code?
Quoted 8 lines
There's not a lot of debugging I can do with this, since I don't have an EVM ... and since this seems to work OK on other boards. (Testing on SDP being easiest, since it's got a slot not tied down with MMC root.)
This patch was basically sent as a seed, since nobody else seemed to be filling in the missing MMC/SD pieces on that board.
I've pushed this, looks like the mux.[ch] changes had already been applied in another patch.
Tony
Quoted 49 lines
- Dave
Quoted 22 lines
[email protected]:~# cat /proc/interrupts CPU0 11: 0 INTC prcm 12: 4 INTC DMA 25: 0 INTC dispc 37: 1724 INTC gp timer 56: 267 INTC i2c_omap 57: 0 INTC i2c_omap 61: 0 INTC i2c_omap 72: 178 INTC serial idle, serial 73: 1 INTC serial idle 74: 1 INTC serial idle 83: 43 INTC mmc0 92: 0 INTC musb_hdrc 93: 0 INTC musb_hdrc 335: 0 GPIO ads7846 336: 3565 GPIO eth0 369: 0 twl4030 twl4030_keypad 378: 0 twl4030 twl4030_usb 384: 0 twl4030 mmc0 Err: 0Quoted 22 lines
Regards
ManiQuoted 19 lines
-----Original Message-----
From: [email protected] [mailto:linux-omap- [email protected]] On Behalf Of David Brownell
Sent: Thursday, February 05, 2009 4:53 AM
To: OMAP
Subject: [patch/rft 2.6.29-rc3-omap-git] omap3 evm: MMC switch supportUpdate OMAP3 EVM board support to support the MMC/SD switches, when used with the twl4030 based power card.
Also, less usefully, LEDB as a GPIO LED ... it's on the underside of the board, so it's probably not very useful to most folk. The LCD backlight is controlled by LEDA though; more useful, though its PWM mode might not be practical on this board (I don't know how that inductor will affect things).
This is done from schematics, so it needs testing (and maybe some bugfixes) from folk with an EVM board.
Quoted 4 lines
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html