Skip to contentSkip to conversation

board support patch for phyCORE-MPC5200B-tiny

PATCH Superseded Jon Smirl 6 participants 13 messages Mar 24, 2009 – Apr 1, 2009 Kbuild

v4 of 6 Superseded Latest is v6 →

lore
Share & tools
lore

Jon Smirl

author
#0 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Add support for the Phytec phyCORE-MPC5200B-tiny. This code is from Pengutronix.de but they didn't sign the patch.

---
 Makefile                            |   10 +
 board/phytec/pcm030/Makefile        |   50 ++++
 board/phytec/pcm030/config.mk       |   42 +++
 board/phytec/pcm030/mt46v32m16-75.h |   54 ++++
 board/phytec/pcm030/pcm030.c        |  206 ++++++++++++++++
 cpu/mpc5xxx/ide.c                   |    3 
 include/configs/pcm030.h            |  463 +++++++++++++++++++++++++++++++++++
 7 files changed, 828 insertions(+), 0 deletions(-)
 create mode 100644 board/phytec/pcm030/Makefile
 create mode 100644 board/phytec/pcm030/config.mk
 create mode 100644 board/phytec/pcm030/mt46v32m16-75.h
 create mode 100644 board/phytec/pcm030/pcm030.c
 create mode 100644 include/configs/pcm030.h
Makefile +10 -0
index ba6a602..7e93dc1 100644
@@ -665,6 +665,16 @@ MVBC_P_config: unconfig
 o2dnt_config:	unconfig
 	@$(MKCONFIG) o2dnt ppc mpc5xxx o2dnt
 
+pcm030_config \
+pcm030_LOWBOOT_config:	unconfig
+	@ >include/config.h
+	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
+		{ echo "TEXT_BASE = 0xFF000000"	>board/phytec/pcm030/config.tmp ; \
+		  echo "... with LOWBOOT configuration" ; \
+		}
+	@$(MKCONFIG) -a pcm030 ppc mpc5xxx pcm030 phytec
+	@ echo "remember to set pcm030_REV to 0 for rev 1245.0 rev or to 1 for rev 1245.1"
+
 pf5200_config:	unconfig
 	@$(MKCONFIG) pf5200  ppc mpc5xxx pf5200 esd
 
board/phytec/pcm030/Makefile new file +50 -0

50 lines not on this page · raw message

board/phytec/pcm030/config.mk new file +42 -0

42 lines not on this page · raw message

board/phytec/pcm030/mt46v32m16-75.h new file +54 -0

54 lines not on this page · raw message

board/phytec/pcm030/pcm030.c new file +206 -0

206 lines not on this page · raw message

cpu/mpc5xxx/ide.c +3 -0
index 9e8f29b..0129180 100644
@@ -45,6 +45,9 @@ int ide_preinit (void)
 #if defined(CONFIG_SYS_ATA_CS_ON_I2C2)
 	/* ATA cs0/1 on i2c2 clk/io */
 	reg = (reg & ~0x03000000ul) | 0x02000000ul;
+#elif defined(CONFIG_PHYCORE_MPC5200B_TINY)
+	/* ATA cs0/1 on Timer 0/1 */
+	reg = (reg & ~0x03000000ul) | 0x03000000ul;
 #else
 	/* ATA cs0/1 on Local Plus cs4/5 */
 	reg = (reg & ~0x03000000ul) | 0x01000000ul;
include/configs/pcm030.h new file +463 -0

463 lines not on this page · raw message

author
#1 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Is this one ok now?

Quoted 902 lines · Jon Smirl

Add support for the Phytec phyCORE-MPC5200B-tiny. This code is from Pengutronix.de but they didn't sign the patch.

---

?Makefile ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? 10 +
?board/phytec/pcm030/Makefile ? ? ? ?| ? 50 ++++
?board/phytec/pcm030/config.mk ? ? ? | ? 42 +++
?board/phytec/pcm030/mt46v32m16-75.h | ? 54 ++++
?board/phytec/pcm030/pcm030.c ? ? ? ?| ?206 ++++++++++++++++
?cpu/mpc5xxx/ide.c ? ? ? ? ? ? ? ? ? | ? ?3
?include/configs/pcm030.h ? ? ? ? ? ?| ?463 +++++++++++++++++++++++++++++++++++

?7 files changed, 828 insertions(+), 0 deletions(-) ?create mode 100644 board/phytec/pcm030/Makefile ?create mode 100644 board/phytec/pcm030/config.mk ?create mode 100644 board/phytec/pcm030/mt46v32m16-75.h ?create mode 100644 board/phytec/pcm030/pcm030.c ?create mode 100644 include/configs/pcm030.h

Makefile +0 -0
index ba6a602..7e93dc1 100644
@@ -665,6 +665,16 @@ MVBC_P_config: unconfig

?o2dnt_config: ?unconfig
? ? ? ?@$(MKCONFIG) o2dnt ppc mpc5xxx o2dnt

Makefile +10 -0
+pcm030_config \
+pcm030_LOWBOOT_config: unconfig
+ ? ? ? @ >include/config.h
+ ? ? ? @[ -z "$(findstring LOWBOOT_,$@)" ] || \
+ ? ? ? ? ? ? ? { echo "TEXT_BASE = 0xFF000000" >board/phytec/pcm030/config.tmp ; \
+ ? ? ? ? ? ? ? ? echo "... with LOWBOOT configuration" ; \
+ ? ? ? ? ? ? ? }
+ ? ? ? @$(MKCONFIG) -a pcm030 ppc mpc5xxx pcm030 phytec
+ ? ? ? @ echo "remember to set pcm030_REV to 0 for rev 1245.0 rev or to 1 for rev 1245.1"
+

?pf5200_config: unconfig
? ? ? ?@$(MKCONFIG) pf5200 ?ppc mpc5xxx pf5200 esd

board/phytec/pcm030/Makefile new file +50 -0
new file mode 100644
index 0000000..22ce8e6
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2003-2007
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB ? ?= $(obj)lib$(BOARD).a
+
+COBJS ?:= $(BOARD).o
+
+SRCS ? := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS ? := $(addprefix $(obj),$(COBJS))
+SOBJS ?:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB): ? ? ? ?$(obj).depend $(OBJS)
+ ? ? ? $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ ? ? ? rm -f $(SOBJS) $(OBJS)
+
+distclean: ? ? clean
+ ? ? ? rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/phytec/pcm030/config.mk new file +42 -0
new file mode 100644
index 0000000..5d3469c
@@ -0,0 +1,42 @@
+#
+# (C) Copyright 2003
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# phyCORE-MPC5200B tiny board:
+#
+# ? ? ?Valid values for TEXT_BASE are:
+#
+# ? ? ?0xFFF00000 ? boot high (standard configuration)
+# ? ? ?0xFF000000 ? boot low
+# ? ? ?0x00100000 ? boot from RAM (for testing only)
+#
+
+sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp
+
+ifndef TEXT_BASE
+## Standard: boot high
+TEXT_BASE = 0xFFF00000
+endif
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)/board
+
board/phytec/pcm030/mt46v32m16-75.h new file +54 -0
new file mode 100644
index 0000000..4b501c6
@@ -0,0 +1,54 @@
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas at motorola.com.
+ *
+ * Eric Schumann, Phytec Messtechnik
+ * adapted for mt46v32m16-75 DDR-RAM
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR ? ? ?1 ? ? ? ? ? ? ? /* is DDR */
+
+/* Settings for XLB = 132 MHz */
+
+#define SDRAM_MODE ? ? 0x018D0000
+#define SDRAM_EMODE ? ?0x40090000
+#define SDRAM_CONTROL ?0x71500F00
+#define SDRAM_CONFIG1 ?0x73711930
+#define SDRAM_CONFIG2 ?0x47770000
+
+/*
+#define SDRAM_MODE ? ? 0x018D0000
+#define SDRAM_EMODE ? ?0x40090000
+#define SDRAM_CONTROL ?0x715f0f00
+#define SDRAM_CONFIG1 ?0x73722930
+#define SDRAM_CONFIG2 ?0x47770000
+*/
+
+/* Settings for XLB = 99 MHz */
+/*
+#define SDRAM_MODE ? ? 0x008D0000
+#define SDRAM_EMODE ? ?0x40090000
+#define SDRAM_CONTROL ?0x714b0f00
+#define SDRAM_CONFIG1 ?0x63611730
+#define SDRAM_CONFIG2 ?0x47670000
+*/
+
+#define SDRAM_TAPDELAY 0x10000000 /* reserved Bit in MPC5200 B3-Step */
board/phytec/pcm030/pcm030.c new file +206 -0
new file mode 100644
index 0000000..3de6b69
@@ -0,0 +1,206 @@
+/*
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas at motorola.com.
+ *
+ * (C) Copyright 2006
+ * Eric Schumann, Phytec Messtechnik GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc5xxx.h>
+#include <pci.h>
+#include <asm-ppc/io.h>
+
+#include "mt46v32m16-75.h"
+
+#ifndef CONFIG_SYS_RAMBOOT
+static void sdram_start(int hi_addr)
+{
+ ? ? ? long hi_addr_bit = hi_addr ? 0x01000000 : 0;
+
+ ? ? ? /* unlock mode register */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL,
+ ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000000 | hi_addr_bit));
+
+ ? ? ? /* precharge all banks */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL,
+ ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000002 | hi_addr_bit));
+
+#if SDRAM_DDR
+ ? ? ? /* set mode register: extended mode */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_MODE, (SDRAM_EMODE));
+
+ ? ? ? /* set mode register: reset DLL */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_MODE,
+ ? ? ? ? ? ? ? (SDRAM_MODE | 0x04000000));
+#endif
+
+ ? ? ? /* precharge all banks */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL,
+ ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000002 | hi_addr_bit));
+
+ ? ? ? /* auto refresh */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL,
+ ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000004 | hi_addr_bit));
+
+ ? ? ? /* set mode register */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_MODE, (SDRAM_MODE));
+
+ ? ? ? /* normal operation */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CTRL,
+ ? ? ? ? ? ? ? (SDRAM_CONTROL | hi_addr_bit));
+
+ ? ? ? /* set CDM clock enable register, set MPC5200B SDRAM bus */
+ ? ? ? /* to reduced driver strength */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_CDM_CLK_ENA, (0x00CFFFFF));
+}
+#endif
+
+/*
+ * ATTENTION: Although partially referenced initdram does NOT make
+ * ? ? ? ? ? real use of CONFIG_SYS_SDRAM_BASE. The code does not
+ * ? ? ? ? ? ?work if CONFIG_SYS_SDRAM_BASE
+ * ? ? ? ? ? ?is something else than 0x00000000.
+ */
+
+phys_size_t initdram(int board_type)
+{
+ ? ? ? ulong dramsize = 0;
+ ? ? ? ulong dramsize2 = 0;
+#ifndef CONFIG_SYS_RAMBOOT
+ ? ? ? ulong test1, test2;
+
+ ? ? ? /* setup SDRAM chip selects */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?/* 256MB at 0x0 */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS0CFG, 0x0000001b);
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?/* disabled */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS1CFG, 0x10000000);
+
+ ? ? ? /* setup config registers */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CONFIG1, SDRAM_CONFIG1);
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CONFIG2, SDRAM_CONFIG2);
+
+#if SDRAM_DDR && SDRAM_TAPDELAY
+ ? ? ? /* set tap delay */
+ ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_CDM_PORCFG, SDRAM_TAPDELAY);
+#endif
+
+ ? ? ? /* find RAM size using SDRAM CS0 only */
+ ? ? ? sdram_start(0);
+ ? ? ? test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000);
+ ? ? ? sdram_start(1);
+ ? ? ? test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000);
+ ? ? ? if (test1 > test2) {
+ ? ? ? ? ? ? ? sdram_start(0);
+ ? ? ? ? ? ? ? dramsize = test1;
+ ? ? ? } else
+ ? ? ? ? ? ? ? dramsize = test2;
+
+ ? ? ? /* memory smaller than 1MB is impossible */
+ ? ? ? if (dramsize < (1 << 20))
+ ? ? ? ? ? ? ? dramsize = 0;
+
+ ? ? ? /* set SDRAM CS0 size according to the amount of RAM found */
+ ? ? ? if (dramsize > 0)
+ ? ? ? ? ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS0CFG,
+ ? ? ? ? ? ? ? ? ? (0x13 + __builtin_ffs(dramsize >> 20) - 1));
+ ? ? ? else
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* disabled */
+ ? ? ? ? ? ? ? out_be32 ((unsigned __iomem *)MPC5XXX_SDRAM_CS0CFG, 0);
+
+#else /* CONFIG_SYS_RAMBOOT */
+
+ ? ? ? /* retrieve size of memory connected to SDRAM CS0 */
+ ? ? ? dramsize = in_be32((unsigned __iomem *)MPC5XXX_SDRAM_CS0CFG) & 0xFF;
+ ? ? ? if (dramsize >= 0x13)
+ ? ? ? ? ? ? ? dramsize = (1 << (dramsize - 0x13)) << 20;
+ ? ? ? else
+ ? ? ? ? ? ? ? dramsize = 0;
+
+ ? ? ? /* retrieve size of memory connected to SDRAM CS1 */
+ ? ? ? dramsize2 = in_be32((unsigned __iomem *)MPC5XXX_SDRAM_CS1CFG) & 0xFF;
+ ? ? ? if (dramsize2 >= 0x13)
+ ? ? ? ? ? ? ? dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
+ ? ? ? else
+ ? ? ? ? ? ? ? dramsize2 = 0;
+
+#endif /* CONFIG_SYS_RAMBOOT */
+
+ ? ? ? return dramsize + dramsize2;
+}
+
+int checkboard(void)
+{
+ ? ? ? puts("Board: phyCORE-MPC5200B-tiny\n");
+ ? ? ? return 0;
+}
+
+#ifdef CONFIG_PCI
+static struct pci_controller hose;
+
+extern void pci_mpc5xxx_init(struct pci_controller *);
+
+void pci_init_board(void)
+{
+ ? ? ? pci_mpc5xxx_init(&hose);
+}
+#endif
+
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t * bd)
+{
+ ? ? ? ft_cpu_setup(blob, bd);
+}
+#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
+
+#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
+
+#define GPIO_PSC2_4 ? ?0x02000000UL
+
+void init_ide_reset(void)
+{
+ ? ? ? debug("init_ide_reset\n");
+
+ ? ? ? /* Configure PSC2_4 as GPIO output for ATA reset */
+ ? ? ? setbits_be32((unsigned __iomem *)MPC5XXX_WU_GPIO_ENABLE, GPIO_PSC2_4);
+ ? ? ? setbits_be32((unsigned __iomem *)MPC5XXX_WU_GPIO_DIR, GPIO_PSC2_4);
+ ? ? ? /* Deassert reset */
+ ? ? ? setbits_be32((unsigned __iomem *)MPC5XXX_WU_GPIO_DATA_O, GPIO_PSC2_4);
+}
+
+void ide_set_reset(int idereset)
+{
+ ? ? ? debug("ide_reset(%d)\n", idereset);
+
+ ? ? ? if (idereset) {
+ ? ? ? ? ? ? ? clrbits_be32((unsigned __iomem *)
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? MPC5XXX_WU_GPIO_DATA_O, GPIO_PSC2_4);
+ ? ? ? ? ? ? ? /* Make a delay. MPC5200 spec says 25 usec min */
+ ? ? ? ? ? ? ? udelay(500000);
+ ? ? ? } else
+ ? ? ? ? ? ? ? setbits_be32((unsigned __iomem *)
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? MPC5XXX_WU_GPIO_DATA_O, GPIO_PSC2_4);
+}
+#endif /* defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET) */
+
cpu/mpc5xxx/ide.c +0 -0
index 9e8f29b..0129180 100644
@@ -45,6 +45,9 @@ int ide_preinit (void)
 ?#if defined(CONFIG_SYS_ATA_CS_ON_I2C2)

? ? ? ?/* ATA cs0/1 on i2c2 clk/io */
? ? ? ?reg = (reg & ~0x03000000ul) | 0x02000000ul; +#elif defined(CONFIG_PHYCORE_MPC5200B_TINY)
+ ? ? ? /* ATA cs0/1 on Timer 0/1 */
+ ? ? ? reg = (reg & ~0x03000000ul) | 0x03000000ul; ?#else
? ? ? ?/* ATA cs0/1 on Local Plus cs4/5 */ ? ? ? ?reg = (reg & ~0x03000000ul) | 0x01000000ul;

include/configs/pcm030.h new file +463 -0
new file mode 100644
index 0000000..c4d7a9a
@@ -0,0 +1,463 @@
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * (C) Copyright 2006
+ * Eric Schumann, Phytec Messatechnik GmbH
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ? ? ? ? See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* #define DEBUG */
+
+/* To build RAMBOOT, add this to the main Makefile
+@[ -z "$(findstring RAMBOOT_,$@)" ] || \
+ ? ? ? { echo "TEXT_BASE = 0x00100000" >board/phycore_mpc5200b_tiny/\
+ ? ? ? ? ? ? ? config.tmp ; \
+ ? ? ? ? echo "... with RAMBOOT configuration" ; \
+ ? ? ? ? echo "... remember to make sure that MBAR is already \
+ ? ? ? ? ? ? ? ? ? ? ? switched to 0xF0000000 !!!" ; \
+ ? ? ? }
+*/
+
+#define CONFIG_BOARDINFO ? ? ? ?"Phytec Phycore mpc5200b tiny"
+
+/*-----------------------------------------------------------------------------
+High Level Configuration Options
+(easy to change)
+-----------------------------------------------------------------------------*/
+#define CONFIG_MPC5xxx ? ? ? ? 1 ? ? ? /* This is an MPC5xxx CPU */
+#define CONFIG_MPC5200 ? ? ? ? 1 ? ? ? /* (more precisely an MPC5200 CPU) */
+#define CONFIG_MPC5200_DDR ? ? 1 ? ? ? /* (with DDR-SDRAM) */
+#define CONFIG_PHYCORE_MPC5200B_TINY 1 /* phyCORE-MPC5200B -> */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* FEC configuration and IDE */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */
+#define BOOTFLAG_COLD ? ? ? ? ?0x01 ? ?/* Normal Power-On: Boot from FLASH ?*/
+#define BOOTFLAG_WARM ? ? ? ? ?0x02 ? ?/* Software reboot ? ? ? ? ? */
+
+/*-----------------------------------------------------------------------------
+Serial console configuration
+-----------------------------------------------------------------------------*/
+#define CONFIG_PSC_CONSOLE ? ? 3 ? ? ? /* console is on PSC3 -> */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*define gps port conf. */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* register later on to ?*/
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*enable UART function! */
+#define CONFIG_BAUDRATE ? ? ? ? ? ? ? ?115200 ?/* ... at 115200 bps */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+
+#define ? ? ? ?CONFIG_TIMESTAMP ? ? ? ?1 ? ? ? /* Print image info with timestamp */
+
+#if (TEXT_BASE == 0xFF000000) ?/* Boot low */
+#define CONFIG_SYS_LOWBOOT 1
+#endif
+/* RAMBOOT will be defined automatically in memory section */
+
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT ? ? ? ? ? ? ? ? "nor0=physmap-flash.0"
+#define MTDPARTS_DEFAULT ? ? ? "mtdparts=physmap-flash.0:256k(ubootl)," \
+ ? ? ? "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)"
+
+/*-----------------------------------------------------------------------------
+Autobooting
+-----------------------------------------------------------------------------*/
+#define CONFIG_BOOTDELAY ? ? ? 3 ? ? ? /* autoboot after 3 seconds */
+#define CONFIG_ZERO_BOOTDELAY_CHECK ? ?/* allow stopping of boot process */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* even with bootdelay=0 */
+#undef CONFIG_BOOTARGS
+
+
+#define CONFIG_PREBOOT "echo;" \
+ ? ? ? "echo Type \"run bootcmd_net\" to load Kernel over TFTP and to "\
+ ? ? ? ? ? ? ? "mount root filesystem over NFS;" \
+ ? ? ? "echo"
+
+#define ? ? ? ?CONFIG_EXTRA_ENV_SETTINGS ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "netdev=eth0\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "mtdparts=mtdparts=physmap-flash.0:256k(ubootl),1792k(kernel)," \
+ ? ? ? ? ? ? ? "13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)\0" ? \
+ ? ? ? "ipaddr=192.168.23.226\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "netmask=255.255.255.0\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "serverip=192.168.23.1\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "gateway=192.168.23.1\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\
+ ? ? ? "uimage=uImage-pcm030\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\
+ ? ? ? "oftree=oftree-pcm030.dtb\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\
+ ? ? ? "jffs2=root-pcm030.jffs2\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "uboot=u-boot-pcm030.bin\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "bargs_base=setenv bootargs console=ttyPSC0,$(baudrate)" ? ? ? ?\
+ ? ? ? ? ? ? ? " $(mtdparts) rw\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "bargs_flash=setenv bootargs $(bootargs) root=/dev/mtdblock2" ? \
+ ? ? ? ? ? ? ? " rootfstype=jffs2\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \
+ ? ? ? "bargs_nfs=setenv bootargs $(bootargs) root=/dev/nfs" ? ? ? ? ? \
+ ? ? ? ? ? ? ? " ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)::" ? \
+ ? ? ? ? ? ? ? "$(netdev):off nfsroot=$(serverip):$(nfsrootfs),v3,tcp\0" \
+ ? ? ? "bcmd_net=run bargs_base bargs_nfs; tftpboot 0x500000 $(uimage);" \
+ ? ? ? ? ? ? ? " tftp 0x400000 $(oftree); bootm 0x500000 - 0x400000\0" \
+ ? ? ? "bcmd_flash=run bargs_base bargs_flash; bootm 0xff040000 - " ? ?\
+ ? ? ? ? ? ? ? "0xfff40000\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\
+ ? ? ? "prg_kernel=tftp 0x400000 $(uimage); erase 0xff040000 0xff1fffff;" \
+ ? ? ? ? ? ? ? " cp.b 0x400000 0xff040000 $(filesize)\0" ? ? ? ? ? ? ? \
+ ? ? ? "prg_jffs2=tftp 0x400000 $(jffs2); erase 0xff200000 0xffefffff; " \
+ ? ? ? ? ? ? ? "cp.b 0x400000 0xff200000 $(filesize)\0" ? ? ? ? ? ? ? ?\
+ ? ? ? "prg_oftree=tftp 0x400000 $(oftree); erase 0xfff40000 0xfff5ffff;" \
+ ? ? ? ? ? ? ? " cp.b 0x400000 0xfff40000 $(filesize)\0" ? ? ? ? ? ? ? \
+ ? ? ? "update=tftpboot 0x400000 $(uboot);erase 0xFFF00000 0xfff3ffff;" \
+ ? ? ? ? ? ? ? " cp.b 0x400000 0xFFF00000 $(filesize)\0" ? ? ? ? ? ? ? \
+ ? ? ? "unlock=yes\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\
+ ? ? ? ""
+
+#define CONFIG_BOOTCOMMAND ? ? ? ? ? ? "run bcmd_flash"
+
+/*--------------------------------------------------------------------------
+IPB Bus clocking configuration.
+ ---------------------------------------------------------------------------*/
+#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK ? ? ? ?/* define for 133MHz speed */
+
+/*-------------------------------------------------------------------------
+ * PCI Mapping:
+ * 0x40000000 - 0x4fffffff - PCI Memory
+ * 0x50000000 - 0x50ffffff - PCI IO Space
+ * ?-----------------------------------------------------------------------*/
+#define CONFIG_PCI ? ? ? ? ? ? ? ? ? ? 1
+#define CONFIG_PCI_PNP ? ? ? ? ? ? ? ? 1
+#define CONFIG_PCI_SCAN_SHOW ? ? ? ? ? 1
+#define CONFIG_PCI_MEM_BUS ? ? ? ? ? ? 0x40000000
+#define CONFIG_PCI_MEM_PHYS ? ? ? ? ? ?CONFIG_PCI_MEM_BUS
+#define CONFIG_PCI_MEM_SIZE ? ? ? ? ? ?0x10000000
+#define CONFIG_PCI_IO_BUS ? ? ? ? ? ? ?0x50000000
+#define CONFIG_PCI_IO_PHYS ? ? ? ? ? ? CONFIG_PCI_IO_BUS
+#define CONFIG_PCI_IO_SIZE ? ? ? ? ? ? 0x01000000
+#define CONFIG_SYS_XLB_PIPELINING ? ? ?1
+
+/*---------------------------------------------------------------------------
+ I2C configuration
+---------------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+/*---------------------------------------------------------------------------
+ EEPROM CAT24WC32 configuration
+---------------------------------------------------------------------------*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR ? ? 0x52 ? ?/* 1010100x */
+#define CONFIG_SYS_I2C_FACT_ADDR ? ? ? 0x52 ? ?/* EEPROM CAT24WC32 */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 ? ? ? /* Bytes of address */
+#define CONFIG_SYS_EEPROM_SIZE ? ? ? ? 2048
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
+
+/*---------------------------------------------------------------------------
+RTC configuration
+---------------------------------------------------------------------------*/
+#define RTC
+#define CONFIG_RTC_PCF8563 ? ? ? ? ? ? 1
+#define CONFIG_SYS_I2C_RTC_ADDR ? ? ? ? ? ? ? ?0x51
+
+/*---------------------------------------------------------------------------
+ Flash configuration
+---------------------------------------------------------------------------*/
+
+#define CONFIG_SYS_FLASH_BASE ? ? ? ? ?0xff000000
+#define CONFIG_SYS_FLASH_SIZE ? ? ? ? ?0x01000000
+#define CONFIG_SYS_FLASH_BANKS_LIST ? ?{ CONFIG_SYS_FLASH_BASE }
+
+#define CONFIG_SYS_FLASH_CFI ? ? ? ? ? 1 ? ? ? /* Flash is CFI conformant */
+#define CONFIG_FLASH_CFI_DRIVER ? ? ? ?1 ? ? ? /* Use the common driver */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_MAX_FLASH_SECT 260 /* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* (= chip selects) */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+/*
+ * Use also hardware protection. This seems required, as the BDI uses
+ * hardware protection. Without this, U-Boot can't work with this sectors,
+ * as its protection is software only by default
+ */
+#define CONFIG_SYS_FLASH_PROTECTION ? ?1
+
+/*---------------------------------------------------------------------------
+ Environment settings
+---------------------------------------------------------------------------*/
+#if 0
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR ? ? ? ? ? ? ? ?(CONFIG_SYS_FLASH_BASE + 0xfe0000)
+#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ?0x20000
+#define CONFIG_ENV_SECT_SIZE ? 0x20000
+#else
+#define CONFIG_ENV_IS_IN_EEPROM ? ? ? ?1
+#define CONFIG_ENV_OFFSET ? ? ?0x00 ? ?/* environment starts at the */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*beginning of the EEPROM */
+#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ?CONFIG_SYS_EEPROM_SIZE
+#endif
+#define CONFIG_ENV_OVERWRITE ? 1
+
+/*-----------------------------------------------------------------------------
+ ?Memory map
+-----------------------------------------------------------------------------*/
+#define CONFIG_SYS_MBAR ? ? ? ?0xF0000000 ? ? ?/* MBAR has to be switched by other */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* bootloader or debugger config ?*/
+#define CONFIG_SYS_SDRAM_BASE ? ? ? ? ?0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR ? ? ? ? ? ? ? ?0x80000000
+/* Use SRAM until RAM will be available */
+#define CONFIG_SYS_INIT_RAM_ADDR ? ? ? MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_END ? ? ? ? ? ? ? ?MPC5XXX_SRAM_SIZE ?/* End of used */
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?/* area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE ? ? ? 128 ? ? /* size in bytes ?*/
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET ? ? (CONFIG_SYS_INIT_RAM_END - \
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET ? ? ?CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_BASE ? ? ? ?TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# ? define CONFIG_SYS_RAMBOOT ? ? ? ? ?1
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor ? */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() ?*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------------
+ Ethernet configuration
+-----------------------------------------------------------------------------*/
+#define CONFIG_MPC5xxx_FEC ? ? ? ? ? ? 1
+#define CONFIG_MPC5xxx_FEC_MII100
+#define CONFIG_PHY_ADDR ? ? ? ? ? ? ? ? ? ? ? ?0x01
+
+/*---------------------------------------------------------------------------
+ GPIO configuration
+ ---------------------------------------------------------------------------*/
+
+/* GPIO port configuration
+ *
+ * Pin mapping:
+ *
+ * [29:31] = 01x
+ * PSC1_0 -> AC97 SDATA out
+ * PSC1_1 -> AC97 SDTA in
+ * PSC1_2 -> AC97 SYNC out
+ * PSC1_3 -> AC97 bitclock out
+ * PSC1_4 -> AC97 reset out
+ *
+ * [25:27] = 001
+ * PSC2_0 -> CAN 1 Tx out
+ * PSC2_1 -> CAN 1 Rx in
+ * PSC2_2 -> CAN 2 Tx out
+ * PSC2_3 -> CAN 2 Rx in
+ * PSC2_4 -> GPIO (claimed for ATA reset, active low)
+ *
+ *
+ * [20:23] = 1100
+ * PSC3_0 -> UART Tx out
+ * PSC3_1 -> UART Rx in
+ * PSC3_2 -> UART RTS (in/out FIXME)
+ * PSC3_3 -> UART CTS (in/out FIXME)
+ * PSC3_4 -> LocalPlus Bus CS6 \
+ * PSC3_5 -> LocalPlus Bus CS7 / --> see [4] and [5]
+ * PSC3_6 -> dedicated SPI MOSI out (master case)
+ * PSC3_7 -> dedicated SPI MISO in (master case)
+ * PSC3_8 -> dedicated SPI SS out (master case)
+ * PSC3_9 -> dedicated SPI CLK out (master case)
+ *
+ * [18:19] = 01
+ * USB_0 -> USB OE out
+ * USB_1 -> USB Tx- out
+ * USB_2 -> USB Tx+ out
+ * USB_3 -> USB RxD (in/out FIXME)
+ * USB_4 -> USB Rx+ in
+ * USB_5 -> USB Rx- in
+ * USB_6 -> USB PortPower out
+ * USB_7 -> USB speed out
+ * USB_8 -> USB suspend (in/out FIXME)
+ * USB_9 -> USB overcurrent in
+ *
+ * [17] = 0
+ * USB differential mode
+ *
+ * [16] = 0
+ * PCI enabled
+ *
+ * [12:15] = 0101
+ * ETH_0 -> ETH Txen
+ * ETH_1 -> ETH TxD0
+ * ETH_2 -> ETH TxD1
+ * ETH_3 -> ETH TxD2
+ * ETH_4 -> ETH TxD3
+ * ETH_5 -> ETH Txerr
+ * ETH_6 -> ETH MDC
+ * ETH_7 -> ETH MDIO
+ * ETH_8 -> ETH RxDv
+ * ETH_9 -> ETH RxCLK
+ * ETH_10 -> ETH Collision
+ * ETH_11 -> ETH TxD
+ * ETH_12 -> ETH RxD0
+ * ETH_13 -> ETH RxD1
+ * ETH_14 -> ETH RxD2
+ * ETH_15 -> ETH RxD3
+ * ETH_16 -> ETH Rxerr
+ * ETH_17 -> ETH CRS
+ *
+ * [9:11] = 101
+ * PSC6_0 -> UART RxD in
+ * PSC6_1 -> UART CTS (in/out FIXME)
+ * PSC6_2 -> UART TxD out
+ * PSC6_3 -> UART RTS (in/out FIXME)
+ *
+ * [2:3/6:7] = 00/11
+ * TMR_0 -> ATA_CS0 out
+ * TMR_1 -> ATA_CS1 out
+ * TMR_2 -> GPIO
+ * TMR_3 -> GPIO
+ * TMR_4 -> GPIO
+ * TMR_5 -> GPIO
+ * TMR_6 -> GPIO
+ * TMR_7 -> GPIO
+ * I2C_0 -> I2C 1 Clock out
+ * I2C_1 -> I2C 1 IO in/out
+ * I2C_2 -> I2C 2 Clock out
+ * I2C_3 -> I2C 2 IO in/out
+ *
+ * [4] = 1
+ * PSC3_5 is used as CS7
+ *
+ * [5] = 1
+ * PSC3_4 is used as CS6
+ *
+ * [1] = 0
+ * gpio_wkup_7 is GPIO
+ *
+ * [0] = 0
+ * gpio_wkup_6 is GPIO
+ *
+ */
+#define CONFIG_SYS_GPS_PORT_CONFIG ? ? 0x0f551c12
+
+/*-----------------------------------------------------------------------------
+ Miscellaneous configurable options
+-------------------------------------------------------------------------------*/
+#define CONFIG_SYS_LONGHELP ? ?/* undef to save memory ? ? */
+#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt ? */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history ? ? */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size ?*/
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size ?*/
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args ? */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM ?*/
+
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_DISPLAY_BOARDINFO 1
+
+/*-----------------------------------------------------------------------------
+ Various low-level settings
+-----------------------------------------------------------------------------*/
+#define CONFIG_SYS_HID0_INIT ? ? ? ? ? HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL ? ? ? ? ?HID0_ICE
+
+/* no burst access on the LPB */
+#define CONFIG_SYS_CS_BURST ? ? ? ? ? ?0x00000000
+/* one deadcycle for the 33MHz statemachine */
+#define CONFIG_SYS_CS_DEADCYCLE ? ? ? ? ? ? ? ?0x33333331
+/* one additional waitstate for the 33MHz statemachine */
+#define CONFIG_SYS_BOOTCS_CFG ? ? ? ? ?0x0001dd00
+#define CONFIG_SYS_BOOTCS_START ? ? ? ? ? ? ? ?CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE ? ? ? ? CONFIG_SYS_FLASH_SIZE
+
+#define CONFIG_SYS_RESET_ADDRESS ? ? ? 0xff000000
+
+/*-----------------------------------------------------------------------
+ * USB stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_USB_CLOCK ? ? ? ? ? ? ? 0x0001BBBB
+#define CONFIG_USB_CONFIG ? ? ? ? ? ? ?0x00001000
+
+/*---------------------------------------------------------------------------
+ IDE/ATA stuff Supports IDE harddisk
+----------------------------------------------------------------------------*/
+
+#undef ?CONFIG_IDE_8xx_PCCARD ?/* Use IDE with PC Card Adapter */
+#undef CONFIG_IDE_8xx_DIRECT ? /* Direct IDE ? ?not supported ?*/
+#undef CONFIG_IDE_LED ? ? ? ? ?/* LED ? for ide not supported ?*/
+#define ? ? ? ?CONFIG_IDE_RESET 1 /* reset for ide supported ? ? ?*/
+#define CONFIG_IDE_PREINIT
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus ? ?*/
+#define CONFIG_SYS_ATA_IDE0_OFFSET ? ? 0x0000
+#define CONFIG_SYS_ATA_BASE_ADDR ? ? ? MPC5XXX_ATA
+/* Offset for data I/O ? ? ? ? ? ? ? ? */
+#define CONFIG_SYS_ATA_DATA_OFFSET ? ? (0x0060)
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET ? ? ?(CONFIG_SYS_ATA_DATA_OFFSET)
+/* Offset for alternate registers ? ? ?*/
+#define CONFIG_SYS_ATA_ALT_OFFSET ? ? ?(0x005C)
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE ? ? ? ? ?4
+#define CONFIG_ATAPI ? ? ? ? ? ? ? ? ? 1
+
+/* we enable IDE and FAT support, so we also need partition support */
+#define CONFIG_DOS_PARTITION ? ?1
+
+/* USB */
+#define CONFIG_USB_OHCI
+#define CONFIG_USB_STORAGE
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT ? ? ? ? ? ? ? 1
+#define CONFIG_OF_BOARD_SETUP ? ? ? ? ?1
+
+#define OF_CPU ? ? ? ? ? ? ? ? ? ? ? ? "PowerPC,5200 at 0"
+#define OF_TBCLK ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_MPC5XXX_CLKIN
+#define OF_SOC ? ? ? ? ? ? ? ? ? ? ? ? "soc5200 at f0000000"
+#define OF_STDOUT_PATH ? ? ? ? ? ? ? ? "/soc5200 at f0000000/serial at 2400"
+
+#endif /* __CONFIG_H */
Signature · 2 lines
Jon Smirl
jonsmirl at gmail.com
#2 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Dear Jon Smirl,

Quoted 6 lines · In message <[email protected]> you…

Is this one ok now?

Quoted 1 line · Jon Smirl

Add support for the Phytec phyCORE-MPC5200B-tiny. This code is from Pengu=

tronix.de but they

Quoted 1 line

didn't sign the patch.

Line too long.

Quoted 4 lines
Quoted 4 lines

---
?Makefile ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ?

Quoted 14 lines

10 +

Quoted 6 lines
?board/phytec/pcm030/Makefile ? ? ? ?| ? 50 ++++
?board/phytec/pcm030/config.mk ? ? ? | ? 42 +++
?board/phytec/pcm030/mt46v32m16-75.h | ? 54 ++++
?board/phytec/pcm030/pcm030.c ? ? ? ?| ?206 ++++++++++++++++
?cpu/mpc5xxx/ide.c ? ? ? ? ? ? ? ? ? | ? ?3
?include/configs/pcm030.h ? ? ? ? ? ?| ?463 +++++++++++++

++++++++++++++++++++++

Quoted 6 lines

?7 files changed, 828 insertions(+), 0 deletions(-) ?create mode 100644 board/phytec/pcm030/Makefile ?create mode 100644 board/phytec/pcm030/config.mk ?create mode 100644 board/phytec/pcm030/mt46v32m16-75.h ?create mode 100644 board/phytec/pcm030/pcm030.c ?create mode 100644 include/configs/pcm030.h

Entries in MAKEALL and in MAINTAINERS missing.

Except from that, it looks OK to me.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"I've finally learned what `upward compatible' means. It means we get
to keep all our old mistakes." - Dennie van Tassel
author
#3 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Quoted 7 lines · Wolfgang Denk
Quoted 5 lines
Quoted 5 lines

?create mode 100644 board/phytec/pcm030/Makefile ?create mode 100644 board/phytec/pcm030/config.mk ?create mode 100644 board/phytec/pcm030/mt46v32m16-75.h ?create mode 100644 board/phytec/pcm030/pcm030.c ?create mode 100644 include/configs/pcm030.h

Entries in MAKEALL and in MAINTAINERS missing.

Sascha and Eric, who going to be the Phytec/Pengutronix maintainer for this? Send me a couple sets of MX35 development hardware and I'll maintain this.

Quoted 6 lines

Except from that, it looks OK to me.

Best regards,

Wolfgang Denk

Signature · 2 lines
Jon Smirl
jonsmirl at gmail.com
#4 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Hi!

Have you read the BIOSEMU stuff in the mailing list?
Can you adjust the PCI section and perhaps you can include the video example (set undef video).

Greats,
Markus

Quoted 28 lines · Jon Smirl
Quoted 7 lines · Wolfgang Denk
Quoted 5 lines
Quoted 5 lines

?create mode 100644 board/phytec/pcm030/Makefile ?create mode 100644 board/phytec/pcm030/config.mk ?create mode 100644 board/phytec/pcm030/mt46v32m16-75.h ?create mode 100644 board/phytec/pcm030/pcm030.c ?create mode 100644 include/configs/pcm030.h

Entries in MAKEALL and in MAINTAINERS missing.

Sascha and Eric, who going to be the Phytec/Pengutronix maintainer for this? Send me a couple sets of MX35 development hardware and I'll maintain this.

Quoted 6 lines

Except from that, it looks OK to me.

Best regards,

Wolfgang Denk

--
Jon Smirl
jonsmirl at gmail.com
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

author
#5 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Quoted 5 lines · Markus Rathgeb

Hi!

Have you read the BIOSEMU stuff in the mailing list?
Can you adjust the PCI section and perhaps you can include the video example (set undef video).

I have v1 of the pcm030 hardware and the baseboard doesn't have a PCI slot.

I looked at some of your older emails. It looks like the framebuffer is not accessible. You are hanging on a write to the PCI bus.

Forget about running the video BIOS initially, just use the memory commands from u-boot to make sure you can read and write the framebuffer. That will ensure that you have your BARs set, PCI timings right, etc.

Quoted 3 lines

Greats,
Markus

Signature · 2 lines
Jon Smirl
jonsmirl at gmail.com
#6 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Quoted 4 lines · Jon Smirl

Forget about running the video BIOS initially, just use the memory commands from u-boot to make sure you can read and write the framebuffer. ?That will ensure that you have your BARs set, PCI timings right, etc.

Have you read the messages (yesterday and today) with the subject:
"What to do for a working BIOSEMU and ATI_RADEON_FB environment?"

I think I used the memory read command

With regards,
Markus

#7 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

In reply to Jon Smirl
Quoted 8 lines · Jon Smirl
Quoted 5 lines · Markus Rathgeb

Hi!

Have you read the BIOSEMU stuff in the mailing list?
Can you adjust the PCI section and perhaps you can include the video example (set undef video).

Quoted 8 lines

I have v1 of the pcm030 hardware and the baseboard doesn't have a PCI slot.

I looked at some of your older emails. It looks like the framebuffer is not accessible. You are hanging on a write to the PCI bus.

Forget about running the video BIOS initially, just use the memory commands from u-boot to make sure you can read and write the framebuffer.

No, memory access to frame buffer will only work after the SD-RAM controller of the GPU is properly initialized. Video BIOS is supposed to do this among other things. As the boot log showed, video memory size was not recognized by the radeon driver which indicates that the video BIOS run failed to initialize the graphic chip and memory controller. Fixing the XLB Initiator Window configuration for bus PCI IO space starting at 0x00000000 seemed to solve problems with video BIOS run.

Best regards,
Anatolij

author
#8 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Quoted 18 lines · Anatolij Gustschin
Quoted 8 lines · Jon Smirl
Quoted 5 lines · Markus Rathgeb

Hi!

Have you read the BIOSEMU stuff in the mailing list?
Can you adjust the PCI section and perhaps you can include the video example (set undef video).

Quoted 8 lines

I have v1 of the pcm030 hardware and the baseboard doesn't have a PCI slot.

I looked at some of your older emails. It looks like the framebuffer is not accessible. You are hanging on a write to the PCI bus.

Forget about running the video BIOS initially, just use the memory commands from u-boot to make sure you can read and write the framebuffer.

Quoted 5 lines

No, memory access to frame buffer will only work after the SD-RAM controller of the GPU is properly initialized. Video BIOS is supposed to do this among other things. As the boot log showed, video memory size was not recognized by the radeon driver which indicates that the video BIOS run failed to initialize the graphic chip and memory

I forgot that it needed to initialize the memory controller.

Quoted 3 lines

controller. Fixing the XLB Initiator Window configuration for bus PCI IO space starting at 0x00000000 seemed to solve problems with video BIOS run.

So you have this working now?

I've only done this from Linux and not u-boot. Linux already has the PCI bus set up properly.

Quoted 5 lines

Best regards,
Anatolij

Signature · 2 lines
Jon Smirl
jonsmirl at gmail.com
#9 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Quoted 25 lines · Jon Smirl
Quoted 18 lines · Anatolij Gustschin
Quoted 8 lines · Jon Smirl
Quoted 5 lines · Markus Rathgeb

Hi!

Have you read the BIOSEMU stuff in the mailing list?
Can you adjust the PCI section and perhaps you can include the video example (set undef video).

Quoted 8 lines

I have v1 of the pcm030 hardware and the baseboard doesn't have a PCI slot.

I looked at some of your older emails. It looks like the framebuffer is not accessible. You are hanging on a write to the PCI bus.

Forget about running the video BIOS initially, just use the memory commands from u-boot to make sure you can read and write the framebuffer.

Quoted 5 lines

No, memory access to frame buffer will only work after the SD-RAM controller of the GPU is properly initialized. Video BIOS is supposed to do this among other things. As the boot log showed, video memory size was not recognized by the radeon driver which indicates that the video BIOS run failed to initialize the graphic chip and memory

Quoted 7 lines

I forgot that it needed to initialize the memory controller.

Quoted 3 lines

controller. Fixing the XLB Initiator Window configuration for bus PCI IO space starting at 0x00000000 seemed to solve problems with video BIOS run.

So you have this working now?

I see the u-boot console with an sweet Tux in upper left corner on the monitor connected to the radeon card.
So I say: Yes, it is working.

When I start Xorg with framebuffer driver (after radeonfb was loaded), this is working, too.

The xorg radeon driver with drm/radeon kernel modul loaded is not completly working.
I will inform you in the next days. Today I have no time anymore.

Quoted 16 lines

I've only done this from Linux and not u-boot. Linux already has the PCI bus set up properly.

Quoted 5 lines

Best regards,
Anatolij

--
Jon Smirl
jonsmirl at gmail.com

author
#10 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

In reply to Anatolij Gustschin
Quoted 14 lines · Anatolij Gustschin
Quoted 13 lines · Jon Smirl
Quoted 5 lines · Markus Rathgeb

Hi!

Have you read the BIOSEMU stuff in the mailing list?
Can you adjust the PCI section and perhaps you can include the video example (set undef video).

I have v1 of the pcm030 hardware and the baseboard doesn't have a PCI slot.

I looked at some of your older emails. It looks like the framebuffer is not accessible. You are hanging on a write to the PCI bus.

Quoted 8 lines
Quoted 3 lines

Forget about running the video BIOS initially, just use the memory commands from u-boot to make sure you can read and write the framebuffer.

No, memory access to frame buffer will only work after the SD-RAM controller of the GPU is properly initialized. Video BIOS is supposed to do this among other things. As the boot log showed, video memory size was not recognized by the radeon driver which indicates that

That comment triggered a memory. There is a bug fix in the fbdev Radeon driver in Linux that pokes an undocumented register. That poke fixes this problem. The problem is only present one some cards, not all. It is a flaw in the ASIC.

I'm looking at the the fbdev driver but I can't remember where the fix is.

Quoted 9 lines

the video BIOS run failed to initialize the graphic chip and memory controller. Fixing the XLB Initiator Window configuration for bus PCI IO space starting at 0x00000000 seemed to solve problems with video BIOS run.

Best regards,
Anatolij

Signature · 2 lines
Jon Smirl
jonsmirl at gmail.com
#11 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

An undocumented register? Are the specifications not released for the series <= r700? But I have to confess to never read the specifications of ATI/AMD.

Have you found something?

Are you able to try to build pcm030_config with a recent checkout?

=============
make -C drivers/rtc/
make[1]: Entering directory
`/home/maggu2810/phytec/u-boot/u-boot.git_20090401/drivers/rtc'
make[1]: Leaving directory
`/home/maggu2810/phytec/u-boot/u-boot.git_20090401/drivers/rtc'
make[1]: Entering directory
`/home/maggu2810/phytec/u-boot/u-boot.git_20090401/drivers/rtc'
powerpc-603e-linux-gnu-gcc -g -Os -fPIC -ffixed-r14 -meabi
-D__KERNEL__ -DTEXT_BASE=0xFFF00000
-I/home/maggu2810/phytec/u-boot/u-boot.git_20090401/include
-fno-builtin -ffreestanding -nostdinc -isystem /home/maggu2810/phytec/OSELAS.Toolchain-1.99.3/powerpc-603e-linux-gnu/gcc-4.3.2-glibc-2.8-binutils-2.18-kernel-2.6.27-sanitized/lib/gcc/powerpc-603e-linux-gnu/4.3.2/include -pipe -DCONFIG_PPC -D__powerpc__ -DCONFIG_MPC5xxx -ffixed-r2 -mstring
-mcpu=603e -mmultiple -DTEXT_BASE=0xFFF00000
-I/home/maggu2810/phytec/u-boot/u-boot.git_20090401/board -Wall
-Wstrict-prototypes -fno-stack-protector -c -o date.o date.c
powerpc-603e-linux-gnu-gcc -g -Os -fPIC -ffixed-r14 -meabi
-D__KERNEL__ -DTEXT_BASE=0xFFF00000
-I/home/maggu2810/phytec/u-boot/u-boot.git_20090401/include
-fno-builtin -ffreestanding -nostdinc -isystem /home/maggu2810/phytec/OSELAS.Toolchain-1.99.3/powerpc-603e-linux-gnu/gcc-4.3.2-glibc-2.8-binutils-2.18-kernel-2.6.27-sanitized/lib/gcc/powerpc-603e-linux-gnu/4.3.2/include -pipe -DCONFIG_PPC -D__powerpc__ -DCONFIG_MPC5xxx -ffixed-r2 -mstring
-mcpu=603e -mmultiple -DTEXT_BASE=0xFFF00000
-I/home/maggu2810/phytec/u-boot/u-boot.git_20090401/board -Wall
-Wstrict-prototypes -fno-stack-protector -c -o pcf8563.o pcf8563.c
pcf8563.c:37: error: static declaration of 'rtc_read' follows
non-static declaration
/home/maggu2810/phytec/u-boot/u-boot.git_20090401/include/rtc.h:64:
error: previous declaration of 'rtc_read' was here
pcf8563.c:38: error: static declaration of 'rtc_write' follows
non-static declaration
/home/maggu2810/phytec/u-boot/u-boot.git_20090401/include/rtc.h:65:
error: previous declaration of 'rtc_write' was here
make[1]: *** [pcf8563.o] Error 1
make[1]: Leaving directory
`/home/maggu2810/phytec/u-boot/u-boot.git_20090401/drivers/rtc'
make: *** [drivers/rtc/librtc.a] Error 2
=============

Quoted 47 lines · Jon Smirl
Quoted 14 lines · Anatolij Gustschin
Quoted 13 lines · Jon Smirl
Quoted 5 lines · Markus Rathgeb

Hi!

Have you read the BIOSEMU stuff in the mailing list?
Can you adjust the PCI section and perhaps you can include the video example (set undef video).

I have v1 of the pcm030 hardware and the baseboard doesn't have a PCI slot.

I looked at some of your older emails. It looks like the framebuffer is not accessible. You are hanging on a write to the PCI bus.

Quoted 8 lines
Quoted 3 lines

Forget about running the video BIOS initially, just use the memory commands from u-boot to make sure you can read and write the framebuffer.

No, memory access to frame buffer will only work after the SD-RAM controller of the GPU is properly initialized. Video BIOS is supposed to do this among other things. As the boot log showed, video memory size was not recognized by the radeon driver which indicates that

That comment triggered a memory. There is a bug fix in the fbdev Radeon driver in Linux that pokes an undocumented register. That poke fixes this problem. The problem is only present one some cards, not all. It is a flaw in the ASIC.

I'm looking at the the fbdev driver but I can't remember where the fix is.

Quoted 9 lines

the video BIOS run failed to initialize the graphic chip and memory controller. Fixing the XLB Initiator Window configuration for bus PCI IO space starting at 0x00000000 seemed to solve problems with video BIOS run.

Best regards,
Anatolij

--
Jon Smirl
jonsmirl at gmail.com

#12 lore raw

PATCH v4 1/1 board support patch for phyCORE-MPC5200B-tiny

Quoted 5 lines · Markus Rathgeb

An undocumented register? Are the specifications not released for the series <= r700? But I have to confess to never read the specifications of ATI/AMD.

Have you found something?

I'm not aware of a released TRM for RV280. And after successful video BIOS run the video memory size of your card should be recognized correctly, isn't it? You can check this with 'DEBUG enabled' drivers/video/ati_radeon_fb.c.

Quoted 1 line

Are you able to try to build pcm030_config with a recent checkout?

<snip>

Quoted 13 lines

powerpc-603e-linux-gnu-gcc -g -Os -fPIC -ffixed-r14 -meabi

(quoted diff) +0 -3
-D__KERNEL__ -DTEXT_BASE=0xFFF00000
-I/home/maggu2810/phytec/u-boot/u-boot.git_20090401/include
-fno-builtin -ffreestanding -nostdinc -isystem

/home/maggu2810/phytec/OSELAS.Toolchain-1.99.3/powerpc-603e-linux-gnu/gcc-4.3.2-glibc-2.8-binutils-2.18-kernel-2.6.27-sanitized/lib/gcc/powerpc-603e-linux-gnu/4.3.2/include

(quoted diff) +0 -4
-pipe  -DCONFIG_PPC -D__powerpc__ -DCONFIG_MPC5xxx -ffixed-r2 -mstring
-mcpu=603e -mmultiple -DTEXT_BASE=0xFFF00000
-I/home/maggu2810/phytec/u-boot/u-boot.git_20090401/board -Wall
-Wstrict-prototypes -fno-stack-protector -c -o pcf8563.o pcf8563.c

pcf8563.c:37: error: static declaration of 'rtc_read' follows non-static declaration /home/maggu2810/phytec/u-boot/u-boot.git_20090401/include/rtc.h:64:
error: previous declaration of 'rtc_read' was here

Quoted 8 lines

pcf8563.c:38: error: static declaration of 'rtc_write' follows non-static declaration /home/maggu2810/phytec/u-boot/u-boot.git_20090401/include/rtc.h:65:
error: previous declaration of 'rtc_write' was here make[1]: *** [pcf8563.o] Error 1
make[1]: Leaving directory `/home/maggu2810/phytec/u-boot/u-boot.git_20090401/drivers/rtc'
make: *** [drivers/rtc/librtc.a] Error 2

apply following patch to fix the build breakage:

http://lists.denx.de/pipermail/u-boot/2009-March/049880.html

Best regards,
Anatolij