Skip to contentSkip to conversation

some kernel issues

DISCUSSION Werner LEMBERG 2 participants 7 messages May 4, 2009 – May 5, 2009 1 message not in the archive

lore
Share & tools
lore
#1 lore raw
In reply to a message not in the archive

[kernel 2.6.30-rc4-14-vanilla from openSuSE factory on top of openSuSE 11.1]

With my 945GM intel graphics card, I don't get TTYs which I could switch to with Ctrl-Alt-Shift-F1, for example, after X has started. Only F7 to switch back to graphics mode works fine. In particular, I don't see any boot messages at start-up. This has worked fine with a previous kernel like 2.6.27.21.

Are there new boot parameters to add or is this a bug? It seems that `vga=0x31a' fails (which openSuSE's yast installer provides) since without it I can see boot messages.

BTW, for `vga=0x31a' I get

Console: colour dummy device 80x25

in the log file, while without this parameter I get

Console: colour VGA+ 80x25

Werner

#2 lore raw
Quoted 10 lines

[kernel 2.6.30-rc4-14-vanilla from openSuSE factory on top of openSuSE 11.1]

With my 945GM intel graphics card, I don't get TTYs which I could switch to with Ctrl-Alt-Shift-F1, for example, after X has started. Only F7 to switch back to graphics mode works fine. In particular, I don't see any boot messages at start-up. This has worked fine with a previous kernel like 2.6.27.21.

I've filed a bug report.

http://bugzilla.kernel.org/show_bug.cgi?id=13249

Werner

#3 lore raw
In reply to Werner LEMBERG
Quoted 15 lines · Werner LEMBERG

[kernel 2.6.30-rc4-14-vanilla from openSuSE factory on top of openSuSE 11.1]

With my 945GM intel graphics card, I don't get TTYs which I could switch to with Ctrl-Alt-Shift-F1, for example, after X has started. Only F7 to switch back to graphics mode works fine.  In particular, I don't see any boot messages at start-up.  This has worked fine with a previous kernel like 2.6.27.21.

Are there new boot parameters to add or is this a bug?  It seems that `vga=0x31a' fails (which openSuSE's yast installer provides) since without it I can see boot messages.

Quoted 7 lines

BTW, for `vga=0x31a' I get

 Console: colour dummy device 80x25

in the log file, while without this parameter I get

 Console: colour VGA+ 80x25

Make sure you haven't enabled kernel mode setting.

CONFIG_DRM_I915_KMS

Dave.

Quoted 9 lines

   Werner
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

#4 lore raw

From: Dave Airlie <[email protected]>
Subject: Re: some kernel issues
Date: Tue, 5 May 2009 20:44:18 +1000

Quoted 9 lines
Quoted 5 lines

With my 945GM intel graphics card, I don't get TTYs which I could switch to with Ctrl-Alt-Shift-F1, for example, after X has started. Only F7 to switch back to graphics mode works fine.  In particular, I don't see any boot messages at start-up.  This has worked fine with a previous kernel like 2.6.27.21.

Make sure you haven't enabled kernel mode setting.

CONFIG_DRM_I915_KMS

Uuuuh, completely undocumented. Thanks! Will check soon.

Werner

#7 lore raw
In reply to Dave Airlie
Quoted 9 lines
Quoted 5 lines

With my 945GM intel graphics card, I don't get TTYs which I could switch to with Ctrl-Alt-Shift-F1, for example, after X has started. Only F7 to switch back to graphics mode works fine.  In particular, I don't see any boot messages at start-up.  This has worked fine with a previous kernel like 2.6.27.21.

Make sure you haven't enabled kernel mode setting.

CONFIG_DRM_I915_KMS

It's not set. BTW, CONFIG_DRM_I915 is set to `m'.

Werner

#5 lore raw
In reply to Werner LEMBERG
Quoted 10 lines · Werner LEMBERG

From: Dave Airlie <[email protected]>
Subject: Re: some kernel issues
Date: Tue, 5 May 2009 20:44:18 +1000

Quoted 6 lines
Quoted 5 lines

With my 945GM intel graphics card, I don't get TTYs which I could switch to with Ctrl-Alt-Shift-F1, for example, after X has started. Only F7 to switch back to graphics mode works fine.  In particular, I don't see any boot messages at start-up.  This has worked fine with a previous kernel like 2.6.27.21.

Quoted 6 lines
Quoted 3 lines

Make sure you haven't enabled kernel mode setting.

CONFIG_DRM_I915_KMS

Uuuuh, completely undocumented.  Thanks!  Will check soon.

Huh?

Choose this option if you want kernel modesetting enabled by default, and you have a new enough userspace to support this. Running old userspaces with this enabled will cause pain. Note that this causes the driver to bind to PCI devices, which precludes loading things like intelfb.

But as you don't have it, it doesn't seem like that is the issue

Dave.

#6 lore raw
Quoted 5 lines
Quoted 4 lines
Quoted 1 line

CONFIG_DRM_I915_KMS

Uuuuh, completely undocumented.  Thanks!  Will check soon.

Quoted 7 lines

Huh?

Choose this option if you want kernel modesetting enabled by default, and you have a new enough userspace to support this. Running old userspaces with this enabled will cause pain. Note that this causes the driver to bind to PCI devices, which precludes loading things like intelfb.

Mea culpa, sorry. I did a grep for CONFIG_DRM_I915_KMS'. Now I know that I have to omit the CONFIG_' part.

Werner