Skip to contentSkip to conversation

Add support for Broadcom BCM63xx SoCs

PATCH New Ralf Baechle 1 participant 13 messages Jul 1, 2009

Subsystems (10)
Networking Network drivers USB MIPS +6 more subsystems
lore
Share & tools
lore
#0 lore raw

cover Add support for Broadcom BCM63xx SoCs

This is a patch series which has been sitting in the linux-bcm63xx git repository for quite a while. I'm posting this series for it to receive the necessary review - in particular the drivers have so far been ignored virtually entirely.

Ralf

#9 lore raw

PATCH 9/12 MIPS: BCM63XX: Add integrated ethernet mac support.

From: Maxime Bizon <[email protected]>

 arch/mips/bcm63xx/Makefile                            |    1 
 arch/mips/bcm63xx/dev-enet.c                          |  156 +
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h |   45 
 drivers/net/Kconfig                                   |    9 
 drivers/net/Makefile                                  |    1 
 drivers/net/bcm63xx_enet.c                            | 1970 ++++++++++++++++++
 drivers/net/bcm63xx_enet.h                            |  303 ++
 7 files changed, 2485 insertions(+)
 create mode 100644 arch/mips/bcm63xx/dev-enet.c
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
 create mode 100644 drivers/net/bcm63xx_enet.c
 create mode 100644 drivers/net/bcm63xx_enet.h
arch/mips/bcm63xx/Makefile +1 -0
@@ -3,6 +3,7 @@ obj-y		+= dev-uart.o
 obj-y		+= dev-pcmcia.o
 obj-y		+= dev-usb-ohci.o
 obj-y		+= dev-usb-ehci.o
+obj-y		+= dev-enet.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 
 EXTRA_CFLAGS += -Werror
arch/mips/bcm63xx/dev-enet.c new file +156 -0

156 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h new file +45 -0

45 lines not on this page · raw message

drivers/net/Kconfig +9 -0
@@ -1919,6 +1919,15 @@ config ATL2
 	  To compile this driver as a module, choose M here.  The module
 	  will be called atl2.
 
+config BCM63XX_ENET
+	tristate "Broadcom 63xx internal mac support"
+	depends on BCM63XX
+	select MII
+	select PHYLIB
+	help
+	  This driver supports the ethernet MACs in the Broadcom 63xx
+	  MIPS chipset family (BCM63XX).
+
 source "drivers/net/fs_enet/Kconfig"
 
 endif # NET_ETHERNET
drivers/net/Makefile +1 -0
@@ -136,6 +136,7 @@ obj-$(CONFIG_B44) += b44.o
 obj-$(CONFIG_FORCEDETH) += forcedeth.o
 obj-$(CONFIG_NE_H8300) += ne-h8300.o 8390.o
 obj-$(CONFIG_AX88796) += ax88796.o
+obj-$(CONFIG_BCM63XX_ENET) += bcm63xx_enet.o
 
 obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
 obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
drivers/net/bcm63xx_enet.c new file +1970 -0

1,970 lines not on this page · raw message

drivers/net/bcm63xx_enet.h new file +303 -0

303 lines not on this page · raw message

#10 lore raw

PATCH 10/12 MIPS: BCM63XX: Add integrated ethernet PHY support for phylib.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 drivers/net/phy/Kconfig   |    6 ++
 drivers/net/phy/Makefile  |    1 
 drivers/net/phy/bcm63xx.c |  132 ++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 139 insertions(+)
 create mode 100644 drivers/net/phy/bcm63xx.c
drivers/net/phy/Kconfig +6 -0
@@ -56,6 +56,12 @@ config BROADCOM_PHY
 	  Currently supports the BCM5411, BCM5421, BCM5461, BCM5464, BCM5481
 	  and BCM5482 PHYs.
 
+config BCM63XX_PHY
+	tristate "Drivers for Broadcom 63xx SOCs internal PHY"
+	depends on BCM63XX
+	---help---
+	  Currently supports the 6348 and 6358 PHYs.
+
 config ICPLUS_PHY
 	tristate "Drivers for ICPlus PHYs"
 	---help---
drivers/net/phy/Makefile +1 -0
@@ -11,6 +11,7 @@ obj-$(CONFIG_QSEMI_PHY)		+= qsemi.o
 obj-$(CONFIG_SMSC_PHY)		+= smsc.o
 obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
 obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
+obj-$(CONFIG_BCM63XX_PHY)	+= bcm63xx.o
 obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
 obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
 obj-$(CONFIG_LSI_ET1011C_PHY)	+= et1011c.o
drivers/net/phy/bcm63xx.c new file +132 -0

132 lines not on this page · raw message

#3 lore raw

PATCH 3/12 MIPS: BCM63XX: Add serial driver for bcm63xx integrated UART.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 arch/mips/bcm63xx/Makefile                            |    1 
 arch/mips/bcm63xx/dev-uart.c                          |   41 
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h |    6 
 drivers/serial/Kconfig                                |   19 
 drivers/serial/Makefile                               |    1 
 drivers/serial/bcm63xx_uart.c                         |  890 ++++++++++++++++++
 include/linux/serial_core.h                           |    2 
 7 files changed, 960 insertions(+)
 create mode 100644 arch/mips/bcm63xx/dev-uart.c
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h
 create mode 100644 drivers/serial/bcm63xx_uart.c
arch/mips/bcm63xx/Makefile +1 -0
@@ -1,4 +1,5 @@
 obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o
+obj-y		+= dev-uart.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 
 EXTRA_CFLAGS += -Werror
arch/mips/bcm63xx/dev-uart.c new file +41 -0

41 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h new file +6 -0
@@ -0,0 +1,6 @@
+#ifndef BCM63XX_DEV_UART_H_
+#define BCM63XX_DEV_UART_H_
+
+int bcm63xx_uart_register(void);
+
+#endif /* BCM63XX_DEV_UART_H_ */
drivers/serial/Kconfig +19 -0
@@ -1451,4 +1451,23 @@ config SERIAL_TIMBERDALE
 	---help---
 	Add support for UART controller on timberdale.
 
+config SERIAL_BCM63XX
+	tristate "bcm63xx serial port support"
+	select SERIAL_CORE
+	depends on BCM63XX
+	help
+	  If you have a bcm63xx CPU, you can enable its onboard
+	  serial port by enabling this options.
+
+          To compile this driver as a module, choose M here: the
+          module will be called bcm963xx_uart.
+
+config SERIAL_BCM63XX_CONSOLE
+	bool "Console on bcm63xx serial port"
+	depends on SERIAL_BCM63XX
+	select SERIAL_CORE_CONSOLE
+	help
+	  If you have enabled the serial port on the bcm63xx CPU
+	  you can make it the console by answering Y to this option.
+
 endmenu
drivers/serial/Makefile +1 -0
@@ -34,6 +34,7 @@ obj-$(CONFIG_SERIAL_CLPS711X) += clps711
 obj-$(CONFIG_SERIAL_PXA) += pxa.o
 obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
 obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
+obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o
 obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
 obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
 obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
drivers/serial/bcm63xx_uart.c new file +890 -0

890 lines not on this page · raw message

include/linux/serial_core.h +2 -0
@@ -174,6 +174,8 @@
 /* Qualcomm MSM SoCs */
 #define PORT_MSM	88
 
+#define PORT_BCM63XX	87
+
 #ifdef __KERNEL__
 
 #include <linux/compiler.h>
#1 lore raw

PATCH 1/12 MIPS: BCM63XX: Add Broadcom 63xx CPU definitions.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

Todo: Nothing ever detects CPU_BCM6338 but the code tests for it anyway.

 arch/mips/include/asm/cpu.h  |    7 +++++++
 arch/mips/kernel/cpu-probe.c |   24 ++++++++++++++++++++++++
 arch/mips/mm/tlbex.c         |    4 ++++
 3 files changed, 35 insertions(+)
arch/mips/include/asm/cpu.h +7 -0
@@ -113,6 +113,12 @@
 
 #define PRID_IMP_BCM4710	0x4000
 #define PRID_IMP_BCM3302	0x9000
+#define PRID_IMP_BCM6338	0x9000
+#define PRID_IMP_BCM6345	0x8000
+#define PRID_IMP_BCM6348	0x9100
+#define PRID_IMP_BCM4350	0xA000
+#define PRID_REV_BCM6358	0x0010
+#define PRID_REV_BCM6368	0x0030
 
 /*
  * These are the PRID's for when 23:16 == PRID_COMP_CAVIUM
@@ -210,6 +216,7 @@ enum cpu_type_enum {
 	 */
 	CPU_4KC, CPU_4KEC, CPU_4KSC, CPU_24K, CPU_34K, CPU_1004K, CPU_74K,
 	CPU_ALCHEMY, CPU_PR4450, CPU_BCM3302, CPU_BCM4710,
+	CPU_BCM6338, CPU_BCM6345, CPU_BCM6348, CPU_BCM6358,
 
 	/*
 	 * MIPS64 class processors
arch/mips/kernel/cpu-probe.c +24 -0
@@ -159,6 +159,10 @@ void __init check_wait(void)
 	case CPU_25KF:
 	case CPU_PR4450:
 	case CPU_BCM3302:
+	case CPU_BCM6338:
+	case CPU_BCM6345:
+	case CPU_BCM6348:
+	case CPU_BCM6358:
 	case CPU_CAVIUM_OCTEON:
 		cpu_wait = r4k_wait;
 		break;
@@ -857,6 +861,7 @@ static inline void cpu_probe_broadcom(st
 	decode_configs(c);
 	switch (c->processor_id & 0xff00) {
 	case PRID_IMP_BCM3302:
+	 /* same as PRID_IMP_BCM6338 */
 		c->cputype = CPU_BCM3302;
 		__cpu_name[cpu] = "Broadcom BCM3302";
 		break;
@@ -864,6 +869,25 @@ static inline void cpu_probe_broadcom(st
 		c->cputype = CPU_BCM4710;
 		__cpu_name[cpu] = "Broadcom BCM4710";
 		break;
+	case PRID_IMP_BCM6345:
+		c->cputype = CPU_BCM6345;
+		__cpu_name[cpu] = "Broadcom BCM6345";
+		break;
+	case PRID_IMP_BCM6348:
+		c->cputype = CPU_BCM6348;
+		__cpu_name[cpu] = "Broadcom BCM6348";
+		break;
+	case PRID_IMP_BCM4350:
+		switch (c->processor_id & 0xf0) {
+		case PRID_REV_BCM6358:
+			c->cputype = CPU_BCM6358;
+			__cpu_name[cpu] = "Broadcom BCM6358";
+			break;
+		default:
+			c->cputype = CPU_UNKNOWN;
+			break;
+		}
+		break;
 	}
 }
 
arch/mips/mm/tlbex.c +4 -0
@@ -321,6 +321,10 @@ static void __cpuinit build_tlb_write_en
 	case CPU_BCM3302:
 	case CPU_BCM4710:
 	case CPU_LOONGSON2:
+	case CPU_BCM6338:
+	case CPU_BCM6345:
+	case CPU_BCM6348:
+	case CPU_BCM6358:
 	case CPU_R5500:
 		if (m4kc_tlbp_war())
 			uasm_i_nop(p);
#2 lore raw

PATCH 2/12 MIPS: BCM63XX: Add support for the Broadcom BCM63xx family of SOCs.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 arch/mips/Kconfig                                          |   18 
 arch/mips/Makefile                                         |    7 
 arch/mips/bcm63xx/Kconfig                                  |    9 
 arch/mips/bcm63xx/Makefile                                 |    4 
 arch/mips/bcm63xx/clk.c                                    |  220 +++
 arch/mips/bcm63xx/cpu.c                                    |  245 ++++
 arch/mips/bcm63xx/cs.c                                     |  144 ++
 arch/mips/bcm63xx/early_printk.c                           |   30 
 arch/mips/bcm63xx/gpio.c                                   |  128 ++
 arch/mips/bcm63xx/irq.c                                    |  253 ++++
 arch/mips/bcm63xx/prom.c                                   |   43 
 arch/mips/bcm63xx/setup.c                                  |  111 +
 arch/mips/bcm63xx/timer.c                                  |  205 +++
 arch/mips/include/asm/fixmap.h                             |    4 
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h           |   11 
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h           |  314 +++++
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_cs.h            |   10 
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h          |   10 
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h            |   93 +
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h           |   15 
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h          |  728 +++++++++++++
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_timer.h         |   11 
 arch/mips/include/asm/mach-bcm63xx/cpu-feature-overrides.h |   51 
 arch/mips/include/asm/mach-bcm63xx/gpio.h                  |   17 
 arch/mips/include/asm/mach-bcm63xx/war.h                   |   25 
 25 files changed, 2705 insertions(+), 1 deletion(-)
 create mode 100644 arch/mips/bcm63xx/Kconfig
 create mode 100644 arch/mips/bcm63xx/Makefile
 create mode 100644 arch/mips/bcm63xx/clk.c
 create mode 100644 arch/mips/bcm63xx/cpu.c
 create mode 100644 arch/mips/bcm63xx/cs.c
 create mode 100644 arch/mips/bcm63xx/early_printk.c
 create mode 100644 arch/mips/bcm63xx/gpio.c
 create mode 100644 arch/mips/bcm63xx/irq.c
 create mode 100644 arch/mips/bcm63xx/prom.c
 create mode 100644 arch/mips/bcm63xx/setup.c
 create mode 100644 arch/mips/bcm63xx/timer.c
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_cs.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_timer.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/cpu-feature-overrides.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/gpio.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/war.h
arch/mips/Kconfig +17 -1
@@ -60,7 +60,7 @@ config BASLER_EXCITE
 	  Basler Vision Technologies AG.
 
 config BCM47XX
-	bool "BCM47XX based boards"
+	bool "Broadcom BCM47XX based boards"
 	select CEVT_R4K
 	select CSRC_R4K
 	select DMA_NONCOHERENT
@@ -80,6 +80,21 @@ config BCM47XX
 	help
 	 Support for BCM47XX based boards
 
+config BCM63XX
+	bool "Broadcom BCM63XX based boards"
+	select CEVT_R4K
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select IRQ_CPU
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
+	select SWAP_IO_SPACE
+	select ARCH_REQUIRE_GPIOLIB
+	help
+	 Support for BCM63XX based boards
+
 config MIPS_COBALT
 	bool "Cobalt Server"
 	select CEVT_R4K
@@ -659,6 +674,7 @@ endchoice
 
 source "arch/mips/alchemy/Kconfig"
 source "arch/mips/basler/excite/Kconfig"
+source "arch/mips/bcm63xx/Kconfig"
 source "arch/mips/jazz/Kconfig"
 source "arch/mips/lasat/Kconfig"
 source "arch/mips/pmc-sierra/Kconfig"
arch/mips/Makefile +7 -0
@@ -560,6 +560,13 @@ cflags-$(CONFIG_BCM47XX)	+= -I$(srctree)
 load-$(CONFIG_BCM47XX)		:= 0xffffffff80001000
 
 #
+# Broadcom BCM63XX boards
+#
+core-$(CONFIG_BCM63XX)		+= arch/mips/bcm63xx/
+cflags-$(CONFIG_BCM63XX)	+= -I$(srctree)/arch/mips/include/asm/mach-bcm63xx/
+load-$(CONFIG_BCM63XX)		:= 0xffffffff80010000
+
+#
 # SNI RM
 #
 core-$(CONFIG_SNI_RM)		+= arch/mips/sni/
arch/mips/bcm63xx/Kconfig new file +9 -0
@@ -0,0 +1,9 @@
+menu "CPU support"
+	depends on BCM63XX
+
+config BCM63XX_CPU_6348
+	bool "support 6348 CPU"
+
+config BCM63XX_CPU_6358
+	bool "support 6358 CPU"
+endmenu
arch/mips/bcm63xx/Makefile new file +4 -0
@@ -0,0 +1,4 @@
+obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o
+obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+
+EXTRA_CFLAGS += -Werror
arch/mips/bcm63xx/clk.c new file +220 -0

220 lines not on this page · raw message

arch/mips/bcm63xx/cpu.c new file +245 -0

245 lines not on this page · raw message

arch/mips/bcm63xx/cs.c new file +144 -0

144 lines not on this page · raw message

arch/mips/bcm63xx/early_printk.c new file +30 -0
@@ -0,0 +1,30 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <[email protected]>
+ */
+
+#include <linux/init.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+static void __init wait_xfered(void)
+{
+	unsigned int val;
+
+	/* wait for any previous char to be transmitted */
+	do {
+		val = bcm_uart0_readl(UART_IR_REG);
+		if (val & UART_IR_STAT(UART_IR_TXEMPTY))
+			break;
+	} while (1);
+}
+
+void __init prom_putchar(char c)
+{
+	wait_xfered();
+	bcm_uart0_writel(c, UART_FIFO_REG);
+	wait_xfered();
+}
arch/mips/bcm63xx/gpio.c new file +128 -0

128 lines not on this page · raw message

arch/mips/bcm63xx/irq.c new file +253 -0

253 lines not on this page · raw message

arch/mips/bcm63xx/prom.c new file +43 -0

43 lines not on this page · raw message

arch/mips/bcm63xx/setup.c new file +111 -0

111 lines not on this page · raw message

arch/mips/bcm63xx/timer.c new file +205 -0

205 lines not on this page · raw message

arch/mips/include/asm/fixmap.h +4 -0
@@ -67,11 +67,15 @@ enum fixed_addresses {
  * the start of the fixmap, and leave one page empty
  * at the top of mem..
  */
+#ifdef CONFIG_BCM63XX
+#define FIXADDR_TOP     ((unsigned long)(long)(int)0xff000000)
+#else
 #if defined(CONFIG_CPU_TX39XX) || defined(CONFIG_CPU_TX49XX)
 #define FIXADDR_TOP	((unsigned long)(long)(int)(0xff000000 - 0x20000))
 #else
 #define FIXADDR_TOP	((unsigned long)(long)(int)0xfffe0000)
 #endif
+#endif
 #define FIXADDR_SIZE	(__end_of_fixed_addresses << PAGE_SHIFT)
 #define FIXADDR_START	(FIXADDR_TOP - FIXADDR_SIZE)
 
arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h new file +11 -0
@@ -0,0 +1,11 @@
+#ifndef BCM63XX_CLK_H_
+#define BCM63XX_CLK_H_
+
+struct clk {
+	void		(*set)(struct clk *, int);
+	unsigned int	rate;
+	unsigned int	usage;
+	int		id;
+};
+
+#endif /* ! BCM63XX_CLK_H_ */
arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h new file +314 -0

314 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/bcm63xx_cs.h new file +10 -0
@@ -0,0 +1,10 @@
+#ifndef BCM63XX_CS_H
+#define BCM63XX_CS_H
+
+int bcm63xx_set_cs_base(unsigned int cs, u32 base, unsigned int size);
+int bcm63xx_set_cs_timing(unsigned int cs, unsigned int wait,
+			   unsigned int setup, unsigned int hold);
+int bcm63xx_set_cs_param(unsigned int cs, u32 flags);
+int bcm63xx_set_cs_status(unsigned int cs, int enable);
+
+#endif /* !BCM63XX_CS_H */
arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h new file +10 -0
@@ -0,0 +1,10 @@
+#ifndef BCM63XX_GPIO_H
+#define BCM63XX_GPIO_H
+
+/* all helpers will BUG() if gpio count is >= 37. */
+#define BCM63XX_GPIO_COUNT	37
+
+#define GPIO_DIR_OUT	0x0
+#define GPIO_DIR_IN	0x1
+
+#endif /* !BCM63XX_GPIO_H */
arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h new file +93 -0

93 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h new file +15 -0
@@ -0,0 +1,15 @@
+#ifndef BCM63XX_IRQ_H_
+#define BCM63XX_IRQ_H_
+
+#include <bcm63xx_cpu.h>
+
+#define IRQ_MIPS_BASE			0
+#define IRQ_INTERNAL_BASE		8
+
+#define IRQ_EXT_BASE			(IRQ_MIPS_BASE + 3)
+#define IRQ_EXT_0			(IRQ_EXT_BASE + 0)
+#define IRQ_EXT_1			(IRQ_EXT_BASE + 1)
+#define IRQ_EXT_2			(IRQ_EXT_BASE + 2)
+#define IRQ_EXT_3			(IRQ_EXT_BASE + 3)
+
+#endif /* ! BCM63XX_IRQ_H_ */
arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h new file +728 -0

728 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/bcm63xx_timer.h new file +11 -0
@@ -0,0 +1,11 @@
+#ifndef BCM63XX_TIMER_H_
+#define BCM63XX_TIMER_H_
+
+int bcm63xx_timer_register(int id, void (*callback)(void *data), void *data);
+void bcm63xx_timer_unregister(int id);
+int bcm63xx_timer_set(int id, int monotonic, unsigned int countdown_us);
+int bcm63xx_timer_enable(int id);
+int bcm63xx_timer_disable(int id);
+unsigned int bcm63xx_timer_countdown(unsigned int countdown_us);
+
+#endif /* !BCM63XX_TIMER_H_ */
arch/mips/include/asm/mach-bcm63xx/cpu-feature-overrides.h new file +51 -0

51 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/gpio.h new file +17 -0
@@ -0,0 +1,17 @@
+#ifndef __ASM_MIPS_MACH_BCM63XX_GPIO_H
+#define __ASM_MIPS_MACH_BCM63XX_GPIO_H
+
+#include <bcm63xx_gpio.h>
+
+#define NR_BUILTIN_GPIO		BCM63XX_GPIO_COUNT
+
+#define gpio_to_irq(gpio)	NULL
+
+#define gpio_get_value __gpio_get_value
+#define gpio_set_value __gpio_set_value
+
+#define gpio_cansleep __gpio_cansleep
+
+#include <asm-generic/gpio.h>
+
+#endif /* __ASM_MIPS_MACH_BCM63XX_GPIO_H */
arch/mips/include/asm/mach-bcm63xx/war.h new file +25 -0
@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2002, 2004, 2007 by Ralf Baechle <[email protected]>
+ */
+#ifndef __ASM_MIPS_MACH_BCM63XX_WAR_H
+#define __ASM_MIPS_MACH_BCM63XX_WAR_H
+
+#define R4600_V1_INDEX_ICACHEOP_WAR	0
+#define R4600_V1_HIT_CACHEOP_WAR	0
+#define R4600_V2_HIT_CACHEOP_WAR	0
+#define R5432_CP0_INTERRUPT_WAR		0
+#define BCM1250_M3_WAR			0
+#define SIBYTE_1956_WAR			0
+#define MIPS4K_ICACHE_REFILL_WAR	0
+#define MIPS_CACHE_SYNC_WAR		0
+#define TX49XX_ICACHE_INDEX_INV_WAR	0
+#define RM9000_CDEX_SMP_WAR		0
+#define ICACHE_REFILLS_WORKAROUND_WAR	0
+#define R10000_LLSC_WAR			0
+#define MIPS34K_MISSED_ITLB_WAR		0
+
+#endif /* __ASM_MIPS_MACH_BCM63XX_WAR_H */
#4 lore raw

PATCH 4/12 MIPS: BCM63XX: Add PCI support.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 arch/mips/bcm63xx/Kconfig                            |    2 
 arch/mips/bcm63xx/setup.c                            |    2 
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pci.h |    6 
 arch/mips/pci/Makefile                               |    2 
 arch/mips/pci/fixup-bcm63xx.c                        |   21 ++
 arch/mips/pci/ops-bcm63xx.c                          |  179 ++++++++++++++++++
 arch/mips/pci/pci-bcm63xx.c                          |  180 +++++++++++++++++++
 arch/mips/pci/pci-bcm63xx.h                          |   27 ++
 8 files changed, 419 insertions(+)
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pci.h
 create mode 100644 arch/mips/pci/fixup-bcm63xx.c
 create mode 100644 arch/mips/pci/ops-bcm63xx.c
 create mode 100644 arch/mips/pci/pci-bcm63xx.c
 create mode 100644 arch/mips/pci/pci-bcm63xx.h
arch/mips/bcm63xx/Kconfig +2 -0
@@ -3,7 +3,9 @@ menu "CPU support"
 
 config BCM63XX_CPU_6348
 	bool "support 6348 CPU"
+	select HW_HAS_PCI
 
 config BCM63XX_CPU_6358
 	bool "support 6358 CPU"
+	select HW_HAS_PCI
 endmenu
arch/mips/bcm63xx/setup.c +2 -0
@@ -108,4 +108,6 @@ void __init plat_mem_setup(void)
 	pm_power_off = bcm63xx_machine_halt;
 
 	set_io_port_base(0);
+	ioport_resource.start = 0;
+	ioport_resource.end = ~0;
 }
arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pci.h new file +6 -0
@@ -0,0 +1,6 @@
+#ifndef BCM63XX_DEV_PCI_H_
+#define BCM63XX_DEV_PCI_H_
+
+extern int bcm63xx_pci_enabled;
+
+#endif /* BCM63XX_DEV_PCI_H_ */
arch/mips/pci/Makefile +2 -0
@@ -16,6 +16,8 @@ obj-$(CONFIG_PCI_VR41XX)	+= ops-vr41xx.o
 obj-$(CONFIG_NEC_MARKEINS)	+= ops-emma2rh.o pci-emma2rh.o fixup-emma2rh.o
 obj-$(CONFIG_PCI_TX4927)	+= ops-tx4927.o
 obj-$(CONFIG_BCM47XX)		+= pci-bcm47xx.o
+obj-$(CONFIG_BCM63XX)		+= pci-bcm63xx.o fixup-bcm63xx.o \
+					ops-bcm63xx.o
 
 #
 # These are still pretty much in the old state, watch, go blind.
arch/mips/pci/fixup-bcm63xx.c new file +21 -0
@@ -0,0 +1,21 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <[email protected]>
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <bcm63xx_cpu.h>
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return bcm63xx_get_irq_number(IRQ_PCI);
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
arch/mips/pci/ops-bcm63xx.c new file +179 -0

179 lines not on this page · raw message

arch/mips/pci/pci-bcm63xx.c new file +180 -0

180 lines not on this page · raw message

arch/mips/pci/pci-bcm63xx.h new file +27 -0
@@ -0,0 +1,27 @@
+#ifndef PCI_BCM63XX_H_
+#define PCI_BCM63XX_H_
+
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_dev_pci.h>
+
+/*
+ * Cardbus shares  the PCI bus, but has  no IDSEL, so a  special id is
+ * reserved for it.  If you have a standard PCI device at this id, you
+ * need to change the following definition.
+ */
+#define CARDBUS_PCI_IDSEL	0x8
+
+/*
+ * defined in ops-bcm63xx.c
+ */
+extern struct pci_ops bcm63xx_pci_ops;
+extern struct pci_ops bcm63xx_cb_ops;
+
+/*
+ * defined in pci-bcm63xx.c
+ */
+extern void __iomem *pci_iospace_start;
+
+#endif /* ! PCI_BCM63XX_H_ */
#5 lore raw

PATCH 5/12 MIPS: BCM63XX: Change PCI code to emulate a fake cardbus bridge.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 arch/mips/pci/ops-bcm63xx.c |  288 ++++++++++++++++++++++++++++++++++++++++++++
 arch/mips/pci/pci-bcm63xx.c |   44 ++++++
 2 files changed, 332 insertions(+)
arch/mips/pci/ops-bcm63xx.c +288 -0
@@ -177,3 +177,291 @@ struct pci_ops bcm63xx_pci_ops = {
 	.read   = bcm63xx_pci_read,
 	.write  = bcm63xx_pci_write
 };
+
+#ifdef CONFIG_CARDBUS
+/*
+ * emulate configuration read access on a cardbus bridge
+ */
+#define FAKE_CB_BRIDGE_SLOT	0x1e
+
+static int fake_cb_bridge_bus_number = -1;
+
+static struct {
+	u16 pci_command;
+	u8 cb_latency;
+	u8 subordinate_busn;
+	u8 cardbus_busn;
+	u8 pci_busn;
+	int bus_assigned;
+	u16 bridge_control;
+
+	u32 mem_base0;
+	u32 mem_limit0;
+	u32 mem_base1;
+	u32 mem_limit1;
+
+	u32 io_base0;
+	u32 io_limit0;
+	u32 io_base1;
+	u32 io_limit1;
+} fake_cb_bridge_regs;
+
+static int fake_cb_bridge_read(int where, int size, u32 *val)
+{
+	unsigned int reg;
+	u32 data;
+
+	data = 0;
+	reg = where >> 2;
+	switch (reg) {
+	case (PCI_VENDOR_ID >> 2):
+	case (PCI_CB_SUBSYSTEM_VENDOR_ID >> 2):
+		/* create dummy vendor/device id from our cpu id */
+		data = (bcm63xx_get_cpu_id() << 16) | PCI_VENDOR_ID_BROADCOM;
+		break;
+
+	case (PCI_COMMAND >> 2):
+		data = (PCI_STATUS_DEVSEL_SLOW << 16);
+		data |= fake_cb_bridge_regs.pci_command;
+		break;
+
+	case (PCI_CLASS_REVISION >> 2):
+		data = (PCI_CLASS_BRIDGE_CARDBUS << 16);
+		break;
+
+	case (PCI_CACHE_LINE_SIZE >> 2):
+		data = (PCI_HEADER_TYPE_CARDBUS << 16);
+		break;
+
+	case (PCI_INTERRUPT_LINE >> 2):
+		/* bridge control */
+		data = (fake_cb_bridge_regs.bridge_control << 16);
+		/* pin:intA line:0xff */
+		data |= (0x1 << 8) | 0xff;
+		break;
+
+	case (PCI_CB_PRIMARY_BUS >> 2):
+		data = (fake_cb_bridge_regs.cb_latency << 24);
+		data |= (fake_cb_bridge_regs.subordinate_busn << 16);
+		data |= (fake_cb_bridge_regs.cardbus_busn << 8);
+		data |= fake_cb_bridge_regs.pci_busn;
+		break;
+
+	case (PCI_CB_MEMORY_BASE_0 >> 2):
+		data = fake_cb_bridge_regs.mem_base0;
+		break;
+
+	case (PCI_CB_MEMORY_LIMIT_0 >> 2):
+		data = fake_cb_bridge_regs.mem_limit0;
+		break;
+
+	case (PCI_CB_MEMORY_BASE_1 >> 2):
+		data = fake_cb_bridge_regs.mem_base1;
+		break;
+
+	case (PCI_CB_MEMORY_LIMIT_1 >> 2):
+		data = fake_cb_bridge_regs.mem_limit1;
+		break;
+
+	case (PCI_CB_IO_BASE_0 >> 2):
+		/* | 1 for 32bits io support */
+		data = fake_cb_bridge_regs.io_base0 | 0x1;
+		break;
+
+	case (PCI_CB_IO_LIMIT_0 >> 2):
+		data = fake_cb_bridge_regs.io_limit0;
+		break;
+
+	case (PCI_CB_IO_BASE_1 >> 2):
+		/* | 1 for 32bits io support */
+		data = fake_cb_bridge_regs.io_base1 | 0x1;
+		break;
+
+	case (PCI_CB_IO_LIMIT_1 >> 2):
+		data = fake_cb_bridge_regs.io_limit1;
+		break;
+	}
+
+	*val = postprocess_read(data, where, size);
+	return PCIBIOS_SUCCESSFUL;
+}
+
+/*
+ * emulate configuration write access on a cardbus bridge
+ */
+static int fake_cb_bridge_write(int where, int size, u32 val)
+{
+	unsigned int reg;
+	u32 data, tmp;
+	int ret;
+
+	ret = fake_cb_bridge_read((where & ~0x3), 4, &data);
+	if (ret != PCIBIOS_SUCCESSFUL)
+		return ret;
+
+	data = preprocess_write(data, val, where, size);
+
+	reg = where >> 2;
+	switch (reg) {
+	case (PCI_COMMAND >> 2):
+		fake_cb_bridge_regs.pci_command = (data & 0xffff);
+		break;
+
+	case (PCI_CB_PRIMARY_BUS >> 2):
+		fake_cb_bridge_regs.cb_latency = (data >> 24) & 0xff;
+		fake_cb_bridge_regs.subordinate_busn = (data >> 16) & 0xff;
+		fake_cb_bridge_regs.cardbus_busn = (data >> 8) & 0xff;
+		fake_cb_bridge_regs.pci_busn = data & 0xff;
+		if (fake_cb_bridge_regs.cardbus_busn)
+			fake_cb_bridge_regs.bus_assigned = 1;
+		break;
+
+	case (PCI_INTERRUPT_LINE >> 2):
+		tmp = (data >> 16) & 0xffff;
+		/* disable memory prefetch support */
+		tmp &= ~PCI_CB_BRIDGE_CTL_PREFETCH_MEM0;
+		tmp &= ~PCI_CB_BRIDGE_CTL_PREFETCH_MEM1;
+		fake_cb_bridge_regs.bridge_control = tmp;
+		break;
+
+	case (PCI_CB_MEMORY_BASE_0 >> 2):
+		fake_cb_bridge_regs.mem_base0 = data;
+		break;
+
+	case (PCI_CB_MEMORY_LIMIT_0 >> 2):
+		fake_cb_bridge_regs.mem_limit0 = data;
+		break;
+
+	case (PCI_CB_MEMORY_BASE_1 >> 2):
+		fake_cb_bridge_regs.mem_base1 = data;
+		break;
+
+	case (PCI_CB_MEMORY_LIMIT_1 >> 2):
+		fake_cb_bridge_regs.mem_limit1 = data;
+		break;
+
+	case (PCI_CB_IO_BASE_0 >> 2):
+		fake_cb_bridge_regs.io_base0 = data;
+		break;
+
+	case (PCI_CB_IO_LIMIT_0 >> 2):
+		fake_cb_bridge_regs.io_limit0 = data;
+		break;
+
+	case (PCI_CB_IO_BASE_1 >> 2):
+		fake_cb_bridge_regs.io_base1 = data;
+		break;
+
+	case (PCI_CB_IO_LIMIT_1 >> 2):
+		fake_cb_bridge_regs.io_limit1 = data;
+		break;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int bcm63xx_cb_read(struct pci_bus *bus, unsigned int devfn,
+			   int where, int size, u32 *val)
+{
+	/* snoop access to slot 0x1e on root bus, we fake a cardbus
+	 * bridge at this location */
+	if (!bus->parent && PCI_SLOT(devfn) == FAKE_CB_BRIDGE_SLOT) {
+		fake_cb_bridge_bus_number = bus->number;
+		return fake_cb_bridge_read(where, size, val);
+	}
+
+	/* a  configuration  cycle for  the  device  behind the  cardbus
+	 * bridge is  actually done as a  type 0 cycle  on the primary
+	 * bus. This means that only  one device can be on the cardbus
+	 * bus */
+	if (fake_cb_bridge_regs.bus_assigned &&
+	    bus->number == fake_cb_bridge_regs.cardbus_busn &&
+	    PCI_SLOT(devfn) == 0)
+		return bcm63xx_do_cfg_read(0, 0,
+					   PCI_DEVFN(CARDBUS_PCI_IDSEL, 0),
+					   where, size, val);
+
+	return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+static int bcm63xx_cb_write(struct pci_bus *bus, unsigned int devfn,
+			    int where, int size, u32 val)
+{
+	if (!bus->parent && PCI_SLOT(devfn) == FAKE_CB_BRIDGE_SLOT) {
+		fake_cb_bridge_bus_number = bus->number;
+		return fake_cb_bridge_write(where, size, val);
+	}
+
+	if (fake_cb_bridge_regs.bus_assigned &&
+	    bus->number == fake_cb_bridge_regs.cardbus_busn &&
+	    PCI_SLOT(devfn) == 0)
+		return bcm63xx_do_cfg_write(0, 0,
+					    PCI_DEVFN(CARDBUS_PCI_IDSEL, 0),
+					    where, size, val);
+
+	return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+struct pci_ops bcm63xx_cb_ops = {
+	.read   = bcm63xx_cb_read,
+	.write   = bcm63xx_cb_write,
+};
+
+/*
+ * only one IO window, so it  cannot be shared by PCI and cardbus, use
+ * fixup to choose and detect unhandled configuration
+ */
+static void bcm63xx_fixup(struct pci_dev *dev)
+{
+	static int io_window = -1;
+	int i, found, new_io_window;
+	u32 val;
+
+	/* look for any io resource */
+	found = 0;
+	for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
+		if (pci_resource_flags(dev, i) & IORESOURCE_IO) {
+			found = 1;
+			break;
+		}
+	}
+
+	if (!found)
+		return;
+
+	/* skip our fake bus with only cardbus bridge on it */
+	if (dev->bus->number == fake_cb_bridge_bus_number)
+		return;
+
+	/* find on which bus the device is */
+	if (fake_cb_bridge_regs.bus_assigned &&
+	    dev->bus->number == fake_cb_bridge_regs.cardbus_busn &&
+	    PCI_SLOT(dev->devfn) == 0)
+		new_io_window = 1;
+	else
+		new_io_window = 0;
+
+	if (new_io_window == io_window)
+		return;
+
+	if (io_window != -1) {
+		printk(KERN_ERR "bcm63xx: both PCI and cardbus devices "
+		       "need IO, which hardware cannot do\n");
+		return;
+	}
+
+	printk(KERN_INFO "bcm63xx: PCI IO window assigned to %s\n",
+	       (new_io_window == 0) ? "PCI" : "cardbus");
+
+	val = bcm_mpi_readl(MPI_L2PIOREMAP_REG);
+	if (io_window)
+		val |= MPI_L2PREMAP_IS_CARDBUS_MASK;
+	else
+		val &= ~MPI_L2PREMAP_IS_CARDBUS_MASK;
+	bcm_mpi_writel(val, MPI_L2PIOREMAP_REG);
+
+	io_window = new_io_window;
+}
+
+DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, bcm63xx_fixup);
+#endif
arch/mips/pci/pci-bcm63xx.c +44 -0

71 lines not on this page · raw message

#6 lore raw

PATCH 6/12 MIPS: BCM63XX: Add PCMCIA & Cardbus support.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 arch/mips/bcm63xx/Makefile                              |    1 
 arch/mips/bcm63xx/dev-pcmcia.c                          |  135 ++++
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h |   13 
 drivers/pcmcia/Kconfig                                  |    4 
 drivers/pcmcia/Makefile                                 |    1 
 drivers/pcmcia/bcm63xx_pcmcia.c                         |  521 ++++++++++++++++
 drivers/pcmcia/bcm63xx_pcmcia.h                         |   65 +
 7 files changed, 740 insertions(+)
 create mode 100644 arch/mips/bcm63xx/dev-pcmcia.c
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h
 create mode 100644 drivers/pcmcia/bcm63xx_pcmcia.c
 create mode 100644 drivers/pcmcia/bcm63xx_pcmcia.h
arch/mips/bcm63xx/Makefile +1 -0
@@ -1,5 +1,6 @@
 obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o
 obj-y		+= dev-uart.o
+obj-y		+= dev-pcmcia.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 
 EXTRA_CFLAGS += -Werror
arch/mips/bcm63xx/dev-pcmcia.c new file +135 -0

135 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h new file +13 -0
@@ -0,0 +1,13 @@
+#ifndef BCM63XX_DEV_PCMCIA_H_
+#define BCM63XX_DEV_PCMCIA_H_
+
+/*
+ * PCMCIA driver platform data
+ */
+struct bcm63xx_pcmcia_platform_data {
+	unsigned int ready_gpio;
+};
+
+int bcm63xx_pcmcia_register(void);
+
+#endif /* BCM63XX_DEV_PCMCIA_H_ */
drivers/pcmcia/Kconfig +4 -0
@@ -192,6 +192,10 @@ config PCMCIA_AU1X00
 	tristate "Au1x00 pcmcia support"
 	depends on SOC_AU1X00 && PCMCIA
 
+config PCMCIA_BCM63XX
+	tristate "bcm63xx pcmcia support"
+	depends on BCM63XX && PCMCIA
+
 config PCMCIA_SA1100
 	tristate "SA1100 support"
 	depends on ARM && ARCH_SA1100 && PCMCIA
drivers/pcmcia/Makefile +1 -0
@@ -27,6 +27,7 @@ obj-$(CONFIG_PCMCIA_SA1111)			+= sa11xx_
 obj-$(CONFIG_M32R_PCC)				+= m32r_pcc.o
 obj-$(CONFIG_M32R_CFC)				+= m32r_cfc.o
 obj-$(CONFIG_PCMCIA_AU1X00)			+= au1x00_ss.o
+obj-$(CONFIG_PCMCIA_BCM63XX)			+= bcm63xx_pcmcia.o
 obj-$(CONFIG_PCMCIA_VRC4171)			+= vrc4171_card.o
 obj-$(CONFIG_PCMCIA_VRC4173)			+= vrc4173_cardu.o
 obj-$(CONFIG_OMAP_CF)				+= omap_cf.o
drivers/pcmcia/bcm63xx_pcmcia.c new file +521 -0

521 lines not on this page · raw message

drivers/pcmcia/bcm63xx_pcmcia.h new file +65 -0

65 lines not on this page · raw message

#7 lore raw

PATCH 7/12 MIPS: BCM63XX: Add USB OHCI support.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 arch/mips/bcm63xx/Kconfig                                 |    6 
 arch/mips/bcm63xx/Makefile                                |    1 
 arch/mips/bcm63xx/dev-usb-ohci.c                          |   50 ++++
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h |    6 
 drivers/usb/host/ohci-bcm63xx.c                           |  164 ++++++++++++++
 drivers/usb/host/ohci-hcd.c                               |    5 
 drivers/usb/host/ohci.h                                   |    7 
 7 files changed, 238 insertions(+), 1 deletion(-)
 create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
 create mode 100644 drivers/usb/host/ohci-bcm63xx.c
arch/mips/bcm63xx/Kconfig +6 -0
@@ -4,8 +4,14 @@ menu "CPU support"
 config BCM63XX_CPU_6348
 	bool "support 6348 CPU"
 	select HW_HAS_PCI
+	select USB_ARCH_HAS_OHCI
+	select USB_OHCI_BIG_ENDIAN_DESC
+	select USB_OHCI_BIG_ENDIAN_MMIO
 
 config BCM63XX_CPU_6358
 	bool "support 6358 CPU"
 	select HW_HAS_PCI
+	select USB_ARCH_HAS_OHCI
+	select USB_OHCI_BIG_ENDIAN_DESC
+	select USB_OHCI_BIG_ENDIAN_MMIO
 endmenu
arch/mips/bcm63xx/Makefile +1 -0
@@ -1,6 +1,7 @@
 obj-y		+= clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o
 obj-y		+= dev-uart.o
 obj-y		+= dev-pcmcia.o
+obj-y		+= dev-usb-ohci.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 
 EXTRA_CFLAGS += -Werror
arch/mips/bcm63xx/dev-usb-ohci.c new file +50 -0

50 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h new file +6 -0
@@ -0,0 +1,6 @@
+#ifndef BCM63XX_DEV_USB_OHCI_H_
+#define BCM63XX_DEV_USB_OHCI_H_
+
+int bcm63xx_ohci_register(void);
+
+#endif /* BCM63XX_DEV_USB_OHCI_H_ */
drivers/usb/host/ohci-bcm63xx.c new file +164 -0

164 lines not on this page · raw message

drivers/usb/host/ohci-hcd.c +5 -0
@@ -1047,6 +1047,11 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		usb_hcd_pnx4008_driver
 #endif
 
+#ifdef CONFIG_BCM63XX
+#include "ohci-bcm63xx.c"
+#define PLATFORM_DRIVER		ohci_hcd_bcm63xx_driver
+#endif
+
 #if defined(CONFIG_CPU_SUBTYPE_SH7720) || \
     defined(CONFIG_CPU_SUBTYPE_SH7721) || \
     defined(CONFIG_CPU_SUBTYPE_SH7763) || \
drivers/usb/host/ohci.h +6 -1
@@ -536,6 +536,11 @@ static inline struct usb_hcd *ohci_to_hc
 #define big_endian_mmio(ohci)	0		/* only little endian */
 #endif
 
+#if defined(CONFIG_MIPS) && defined(CONFIG_BCM63XX)
+#define readl_be(addr)		__raw_readl((__force unsigned *)addr)
+#define writel_be(val, addr)	__raw_writel(val, (__force unsigned *)addr)
+#endif
+
 /*
  * Big-endian read/write functions are arch-specific.
  * Other arches can be added if/when they're needed.
@@ -646,7 +651,7 @@ static inline u32 hc32_to_cpup (const st
  * some big-endian SOC implementations.  Same thing happens with PSW access.
  */
 
-#ifdef CONFIG_PPC_MPC52xx
+#if defined(CONFIG_PPC_MPC52xx) || defined(CONFIG_BCM63XX)
 #define big_endian_frame_no_quirk(ohci)	(ohci->flags & OHCI_QUIRK_FRAME_NO)
 #else
 #define big_endian_frame_no_quirk(ohci)	0
#8 lore raw

PATCH 8/12 MIPS: BCM63XX: Add USB EHCI support.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 arch/mips/bcm63xx/Kconfig                                 |    2 
 arch/mips/bcm63xx/Makefile                                |    1 
 arch/mips/bcm63xx/dev-usb-ehci.c                          |   50 ++++
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h |    6 
 drivers/usb/host/ehci-bcm63xx.c                           |  155 ++++++++++++++
 drivers/usb/host/ehci-hcd.c                               |    5 
 drivers/usb/host/ehci.h                                   |    5 
 7 files changed, 224 insertions(+)
 create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
 create mode 100644 drivers/usb/host/ehci-bcm63xx.c
arch/mips/bcm63xx/Kconfig +2 -0
@@ -14,4 +14,6 @@ config BCM63XX_CPU_6358
 	select USB_ARCH_HAS_OHCI
 	select USB_OHCI_BIG_ENDIAN_DESC
 	select USB_OHCI_BIG_ENDIAN_MMIO
+	select USB_ARCH_HAS_EHCI
+	select USB_EHCI_BIG_ENDIAN_MMIO
 endmenu
arch/mips/bcm63xx/Makefile +1 -0
@@ -2,6 +2,7 @@ obj-y		+= clk.o cpu.o cs.o gpio.o irq.o 
 obj-y		+= dev-uart.o
 obj-y		+= dev-pcmcia.o
 obj-y		+= dev-usb-ohci.o
+obj-y		+= dev-usb-ehci.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 
 EXTRA_CFLAGS += -Werror
arch/mips/bcm63xx/dev-usb-ehci.c new file +50 -0

50 lines not on this page · raw message

arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h new file +6 -0
@@ -0,0 +1,6 @@
+#ifndef BCM63XX_DEV_USB_EHCI_H_
+#define BCM63XX_DEV_USB_EHCI_H_
+
+int bcm63xx_ehci_register(void);
+
+#endif /* BCM63XX_DEV_USB_EHCI_H_ */
drivers/usb/host/ehci-bcm63xx.c new file +155 -0

155 lines not on this page · raw message

drivers/usb/host/ehci-hcd.c +5 -0
@@ -1117,6 +1117,11 @@ MODULE_LICENSE ("GPL");
 #define	PLATFORM_DRIVER		ixp4xx_ehci_driver
 #endif
 
+#ifdef CONFIG_BCM63XX
+#include "ehci-bcm63xx.c"
+#define	PLATFORM_DRIVER		ehci_hcd_bcm63xx_driver
+#endif
+
 #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER)
 #error "missing bus glue for ehci-hcd"
drivers/usb/host/ehci.h +5 -0
@@ -598,6 +598,11 @@ ehci_port_speed(struct ehci_hcd *ehci, u
 #define writel_be(val, addr)	__raw_writel(val, (__force unsigned *)addr)
 #endif
 
+#if defined(CONFIG_MIPS) && defined(CONFIG_BCM63XX)
+#define readl_be(addr)		__raw_readl((__force unsigned *)addr)
+#define writel_be(val, addr)	__raw_writel(val, (__force unsigned *)addr)
+#endif
+
 static inline unsigned int ehci_readl(const struct ehci_hcd *ehci,
 		__u32 __iomem * regs)
 {
#11 lore raw

PATCH 11/12 MIPS: BCM63XX: Add board support code.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

BCM6348-based:
- 96348R
- 96348gw
- 96348GW-10
- 96348GW-11
- 96348GW-A
- Sagem F@2404
- Davolink DV201AMR

BCM6358-based:
- 96358vw
- 96358vw2
- Pirelli/Alice AGPFS0

 arch/mips/bcm63xx/Kconfig                           |    2 
 arch/mips/bcm63xx/Makefile                          |    2 
 arch/mips/bcm63xx/boards/Kconfig                    |   11 
 arch/mips/bcm63xx/boards/Makefile                   |    3 
 arch/mips/bcm63xx/boards/board_bcm963xx.c           |  532 ++++++++++++++++++++
 arch/mips/bcm63xx/prom.c                            |    4 
 arch/mips/bcm63xx/setup.c                           |   16 
 arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h  |   12 
 arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h |   50 +
 9 files changed, 630 insertions(+), 2 deletions(-)
 create mode 100644 arch/mips/bcm63xx/boards/Kconfig
 create mode 100644 arch/mips/bcm63xx/boards/Makefile
 create mode 100644 arch/mips/bcm63xx/boards/board_bcm963xx.c
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h
 create mode 100644 arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
arch/mips/bcm63xx/Kconfig +2 -0
@@ -17,3 +17,5 @@ config BCM63XX_CPU_6358
 	select USB_ARCH_HAS_EHCI
 	select USB_EHCI_BIG_ENDIAN_MMIO
 endmenu
+
+source "arch/mips/bcm63xx/boards/Kconfig"
arch/mips/bcm63xx/Makefile +2 -0
@@ -6,4 +6,6 @@ obj-y		+= dev-usb-ehci.o
 obj-y		+= dev-enet.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 
+obj-y		+= boards/
+
 EXTRA_CFLAGS += -Werror
arch/mips/bcm63xx/boards/Kconfig new file +11 -0
@@ -0,0 +1,11 @@
+choice
+	prompt "Board support"
+	depends on BCM63XX
+	default BOARD_BCM963XX
+
+config BOARD_BCM963XX
+       bool "Generic Broadcom 963xx boards"
+	select SSB
+       help
+
+endchoice
arch/mips/bcm63xx/boards/Makefile new file +3 -0
@@ -0,0 +1,3 @@
+obj-$(CONFIG_BOARD_BCM963XX)		+= board_bcm963xx.o
+
+EXTRA_CFLAGS += -Werror
arch/mips/bcm63xx/boards/board_bcm963xx.c new file +532 -0

532 lines not on this page · raw message

arch/mips/bcm63xx/prom.c +4 -0
@@ -9,6 +9,7 @@
 #include <linux/init.h>
 #include <linux/bootmem.h>
 #include <asm/bootinfo.h>
+#include <bcm63xx_board.h>
 #include <bcm63xx_cpu.h>
 #include <bcm63xx_io.h>
 #include <bcm63xx_regs.h>
@@ -36,6 +37,9 @@ void __init prom_init(void)
 
 	/* assign command line from kernel config */
 	strcpy(arcs_cmdline, CONFIG_CMDLINE);
+
+	/* do low level board init */
+	board_prom_init();
 }
 
 void __init prom_free_prom_memory(void)
arch/mips/bcm63xx/setup.c +14 -2
@@ -16,6 +16,7 @@
 #include <asm/time.h>
 #include <asm/reboot.h>
 #include <asm/cacheflush.h>
+#include <bcm63xx_board.h>
 #include <bcm63xx_cpu.h>
 #include <bcm63xx_regs.h>
 #include <bcm63xx_io.h>
@@ -90,8 +91,9 @@ static void __bcm63xx_machine_reboot(cha
 const char *get_system_type(void)
 {
 	static char buf[128];
-	sprintf(buf, "bcm963xx (0x%04x/0x%04X)",
-		bcm63xx_get_cpu_id(), bcm63xx_get_cpu_rev());
+	snprintf(buf, sizeof(buf), "bcm63xx/%s (0x%04x/0x%04X)",
+		 board_get_name(),
+		 bcm63xx_get_cpu_id(), bcm63xx_get_cpu_rev());
 	return buf;
 }
 
@@ -99,6 +101,7 @@ void __init plat_time_init(void)
 {
 	mips_hpt_frequency = bcm63xx_get_cpu_freq() / 2;
 }
+
 void __init plat_mem_setup(void)
 {
 	add_memory_region(0, bcm63xx_get_memory_size(), BOOT_MEM_RAM);
@@ -110,4 +113,13 @@ void __init plat_mem_setup(void)
 	set_io_port_base(0);
 	ioport_resource.start = 0;
 	ioport_resource.end = ~0;
+
+	board_setup();
+}
+
+int __init bcm63xx_register_devices(void)
+{
+	return board_register_devices();
 }
+
+arch_initcall(bcm63xx_register_devices);
arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h new file +12 -0
@@ -0,0 +1,12 @@
+#ifndef BCM63XX_BOARD_H_
+#define BCM63XX_BOARD_H_
+
+const char *board_get_name(void);
+
+void board_prom_init(void);
+
+void board_setup(void);
+
+int board_register_devices(void);
+
+#endif /* ! BCM63XX_BOARD_H_ */
arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h new file +50 -0

50 lines not on this page · raw message

#12 lore raw

PATCH 12/12 MIPS: BCM63XX: Add defconfig.

In reply to Ralf Baechle

From: Maxime Bizon <[email protected]>

 arch/mips/configs/bcm63xx_defconfig |  972 ++++++++++++++++++++++++++++++++++++
 1 file changed, 972 insertions(+)
 create mode 100644 arch/mips/configs/bcm63xx_defconfig
arch/mips/configs/bcm63xx_defconfig new file +972 -0
@@ -0,0 +1,972 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.30-rc6
+# Sun May 31 20:17:18 2009
+#
+CONFIG_MIPS=y
+
+#
+# Machine selection
+#
+# CONFIG_MACH_ALCHEMY is not set
+# CONFIG_BASLER_EXCITE is not set
+# CONFIG_BCM47XX is not set
+CONFIG_BCM63XX=y
+# CONFIG_MIPS_COBALT is not set
+# CONFIG_MACH_DECSTATION is not set
+# CONFIG_MACH_JAZZ is not set
+# CONFIG_LASAT is not set
+# CONFIG_LEMOTE_FULONG is not set
+# CONFIG_MIPS_MALTA is not set
+# CONFIG_MIPS_SIM is not set
+# CONFIG_NEC_MARKEINS is not set
+# CONFIG_MACH_VR41XX is not set
+# CONFIG_NXP_STB220 is not set
+# CONFIG_NXP_STB225 is not set
+# CONFIG_PNX8550_JBS is not set
+# CONFIG_PNX8550_STB810 is not set
+# CONFIG_PMC_MSP is not set
+# CONFIG_PMC_YOSEMITE is not set
+# CONFIG_SGI_IP22 is not set
+# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP28 is not set
+# CONFIG_SGI_IP32 is not set
+# CONFIG_SIBYTE_CRHINE is not set
+# CONFIG_SIBYTE_CARMEL is not set
+# CONFIG_SIBYTE_CRHONE is not set
+# CONFIG_SIBYTE_RHONE is not set
+# CONFIG_SIBYTE_SWARM is not set
+# CONFIG_SIBYTE_LITTLESUR is not set
+# CONFIG_SIBYTE_SENTOSA is not set
+# CONFIG_SIBYTE_BIGSUR is not set
+# CONFIG_SNI_RM is not set
+# CONFIG_MACH_TX39XX is not set
+# CONFIG_MACH_TX49XX is not set
+# CONFIG_MIKROTIK_RB532 is not set
+# CONFIG_WR_PPMC is not set
+# CONFIG_CAVIUM_OCTEON_SIMULATOR is not set
+# CONFIG_CAVIUM_OCTEON_REFERENCE_BOARD is not set
+
+#
+# CPU support
+#
+CONFIG_BCM63XX_CPU_6348=y
+CONFIG_BCM63XX_CPU_6358=y
+CONFIG_BOARD_BCM963XX=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_CEVT_R4K_LIB=y
+CONFIG_CEVT_R4K=y
+CONFIG_CSRC_R4K_LIB=y
+CONFIG_CSRC_R4K=y
+CONFIG_DMA_NONCOHERENT=y
+CONFIG_DMA_NEED_PCI_MAP_STATE=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+# CONFIG_HOTPLUG_CPU is not set
+# CONFIG_NO_IOPORT is not set
+CONFIG_GENERIC_GPIO=y
+CONFIG_CPU_BIG_ENDIAN=y
+# CONFIG_CPU_LITTLE_ENDIAN is not set
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_IRQ_CPU=y
+CONFIG_SWAP_IO_SPACE=y
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+
+#
+# CPU selection
+#
+# CONFIG_CPU_LOONGSON2 is not set
+CONFIG_CPU_MIPS32_R1=y
+# CONFIG_CPU_MIPS32_R2 is not set
+# CONFIG_CPU_MIPS64_R1 is not set
+# CONFIG_CPU_MIPS64_R2 is not set
+# CONFIG_CPU_R3000 is not set
+# CONFIG_CPU_TX39XX is not set
+# CONFIG_CPU_VR41XX is not set
+# CONFIG_CPU_R4300 is not set
+# CONFIG_CPU_R4X00 is not set
+# CONFIG_CPU_TX49XX is not set
+# CONFIG_CPU_R5000 is not set
+# CONFIG_CPU_R5432 is not set
+# CONFIG_CPU_R5500 is not set
+# CONFIG_CPU_R6000 is not set
+# CONFIG_CPU_NEVADA is not set
+# CONFIG_CPU_R8000 is not set
+# CONFIG_CPU_R10000 is not set
+# CONFIG_CPU_RM7000 is not set
+# CONFIG_CPU_RM9000 is not set
+# CONFIG_CPU_SB1 is not set
+# CONFIG_CPU_CAVIUM_OCTEON is not set
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPSR1=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_HARDWARE_WATCHPOINTS=y
+
+#
+# Kernel type
+#
+CONFIG_32BIT=y
+# CONFIG_64BIT is not set
+CONFIG_PAGE_SIZE_4KB=y
+# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PAGE_SIZE_16KB is not set
+# CONFIG_PAGE_SIZE_32KB is not set
+# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_MT_SMP is not set
+# CONFIG_MIPS_MT_SMTC is not set
+CONFIG_CPU_HAS_LLSC=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_48 is not set
+# CONFIG_HZ_100 is not set
+# CONFIG_HZ_128 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_256 is not set
+# CONFIG_HZ_1000 is not set
+# CONFIG_HZ_1024 is not set
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+# CONFIG_KEXEC is not set
+# CONFIG_SECCOMP is not set
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+# CONFIG_SYSVIPC is not set
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+# CONFIG_BLK_DEV_INITRD is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+# CONFIG_STRIP_ASM_SYMS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+# CONFIG_PCSPKR_PLATFORM is not set
+CONFIG_BASE_FULL=y
+# CONFIG_FUTEX is not set
+# CONFIG_EPOLL is not set
+# CONFIG_SIGNALFD is not set
+# CONFIG_TIMERFD is not set
+# CONFIG_EVENTFD is not set
+# CONFIG_SHMEM is not set
+# CONFIG_AIO is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_PCI_QUIRKS=y
+# CONFIG_SLUB_DEBUG is not set
+CONFIG_COMPAT_BRK=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_SLOW_WORK is not set
+# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_MODULES is not set
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+CONFIG_DEFAULT_NOOP=y
+CONFIG_DEFAULT_IOSCHED="noop"
+# CONFIG_FREEZER is not set
+
+#
+# Bus options (PCI, PCMCIA, EISA, ISA, TC)
+#
+CONFIG_HW_HAS_PCI=y
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCI_LEGACY is not set
+# CONFIG_PCI_STUB is not set
+# CONFIG_PCI_IOV is not set
+CONFIG_MMU=y
+CONFIG_PCCARD=y
+# CONFIG_PCMCIA_DEBUG is not set
+CONFIG_PCMCIA=y
+CONFIG_PCMCIA_LOAD_CIS=y
+CONFIG_PCMCIA_IOCTL=y
+CONFIG_CARDBUS=y
+
+#
+# PC-card bridges
+#
+# CONFIG_YENTA is not set
+# CONFIG_PD6729 is not set
+# CONFIG_I82092 is not set
+CONFIG_PCMCIA_BCM63XX=y
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Executable file formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_HAVE_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+CONFIG_TRAD_SIGNALS=y
+
+#
+# Power management options
+#
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+# CONFIG_PM is not set
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_PACKET is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_PNP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+# CONFIG_MTD_CHAR is not set
+# CONFIG_MTD_BLKDEVS is not set
+# CONFIG_MTD_BLOCK is not set
+# CONFIG_MTD_BLOCK_RO is not set
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
+# CONFIG_MTD_INTEL_VR_NOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+# CONFIG_BLK_DEV is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+
+#
+# Enable only one of the two stacks, unless you know what you are doing
+#
+# CONFIG_FIREWIRE is not set
+# CONFIG_IEEE1394 is not set
+# CONFIG_I2O is not set
+CONFIG_NETDEVICES=y
+CONFIG_COMPAT_NET_DEV_OPS=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_ARCNET is not set
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_DAVICOM_PHY is not set
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+CONFIG_BCM63XX_PHY=y
+# CONFIG_ICPLUS_PHY is not set
+# CONFIG_REALTEK_PHY is not set
+# CONFIG_NATIONAL_PHY is not set
+# CONFIG_STE10XP is not set
+# CONFIG_LSI_ET1011C_PHY is not set
+# CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_DNET is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
+# CONFIG_ATL2 is not set
+CONFIG_BCM63XX_ENET=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_NET_PCMCIA is not set
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_DEVKMEM is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_BCM63XX=y
+CONFIG_SERIAL_BCM63XX_CONSOLE=y
+# CONFIG_UNIX98_PTYS is not set
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+
+#
+# PCMCIA character devices
+#
+# CONFIG_SYNCLINK_CS is not set
+# CONFIG_CARDMAN_4000 is not set
+# CONFIG_CARDMAN_4040 is not set
+# CONFIG_IPWIRELESS is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_DEVPORT=y
+# CONFIG_I2C is not set
+# CONFIG_SPI is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+
+#
+# PCI GPIO expanders:
+#
+# CONFIG_GPIO_BT8XX is not set
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB=y
+CONFIG_SSB_SPROM=y
+CONFIG_SSB_PCIHOST_POSSIBLE=y
+CONFIG_SSB_PCIHOST=y
+# CONFIG_SSB_B43_PCI_BRIDGE is not set
+CONFIG_SSB_PCMCIAHOST_POSSIBLE=y
+# CONFIG_SSB_PCMCIAHOST is not set
+# CONFIG_SSB_SILENT is not set
+# CONFIG_SSB_DEBUG is not set
+CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
+# CONFIG_SSB_DRIVER_PCICORE is not set
+# CONFIG_SSB_DRIVER_MIPS is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_REGULATOR is not set
+
+#
+# Multimedia devices
+#
+
+#
+# Multimedia core support
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+# CONFIG_SOUND is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+
+#
+# Miscellaneous USB options
+#
+# CONFIG_USB_DEVICEFS is not set
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_OTG_WHITELIST is not set
+# CONFIG_USB_OTG_BLACKLIST_HUB is not set
+# CONFIG_USB_MON is not set
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_HCD_SSB is not set
+CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
+CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_UHCI_HCD is not set
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_WHCI_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+
+#
+# USB port drivers
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+# CONFIG_USB_GADGET is not set
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_NOP_USB_XCEIV is not set
+# CONFIG_UWB is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_NEW_LEDS is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_INFINIBAND is not set
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_FILE_LOCKING is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+# CONFIG_JFFS2_FS is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+# CONFIG_NETWORK_FILESYSTEMS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+# CONFIG_NLS is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+CONFIG_TRACING_SUPPORT=y
+
+#
+# Tracers
+#
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_CMDLINE="console=ttyS0,115200"
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+# CONFIG_CRYPTO is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y