Skip to contentSkip to conversation

init_constants_early: too small LEBs?

DISCUSSION Ralf Schlatterbeck 2 participants 3 messages Nov 19, 2016 – Nov 20, 2016 Memory technology devices (MTD)

lore
Share & tools
lore
#0 lore raw

I'm trying to get an ubifs on a 2MB NOR flash.

I'm following the usual steps for generating everything from inside the embedded system:
ubiformat /dev/mtd7
ubiattach /dev/ubi_ctrl -m 7 -d 7
ubimkvol /dev/ubi7 -N testvol -s 1968KiB

But when I try to mount I'm getting:

# mount -t ubifs /dev/ubi7_0 /mnt/
mount: mounting /dev/ubi7_0 on /mnt/ failed: Invalid argument

and the kernel log tells me:

Nov 19 21:07:33 board kernel: UBIFS error (pid 1504):

init_constants_early: too small LEBs (3968 bytes), min. is 15360 bytes

Any advice on what to try next?

Should I use a jffs2 on top of UBI using gluebi or run jffs2 on the naked md device instead? I'd really like to be bad block tolerant but don't know if this makes sense with NOR-Flash (of this size) at all.

Thanks
Ralf

Signature · 3 lines
Dr. Ralf Schlatterbeck                  Tel:   +43/2243/26465-16
Open Source Consulting                  www:   http://www.runtux.com
Reichergasse 131, A-3411 Weidling       email: [email protected]
#1 lore raw

Hi Ralf,

Quoted 12 lines · On Sat, 19 Nov 2016 22:25:08 +0100 Ralf Schlatterbeck <[email protected]> wrote:

I'm trying to get an ubifs on a 2MB NOR flash.

I'm following the usual steps for generating everything from inside the embedded system:
ubiformat /dev/mtd7
ubiattach /dev/ubi_ctrl -m 7 -d 7
ubimkvol /dev/ubi7 -N testvol -s 1968KiB

But when I try to mount I'm getting:

# mount -t ubifs /dev/ubi7_0 /mnt/
mount: mounting /dev/ubi7_0 on /mnt/ failed: Invalid argument
Quoted 8 lines

and the kernel log tells me:

Nov 19 21:07:33 board kernel: UBIFS error (pid 1504):

init_constants_early: too small LEBs (3968 bytes), min. is 15360 bytes

Any advice on what to try next?

Should I use a jffs2 on top of UBI using gluebi or run jffs2 on the naked md device instead?

Why not putting JFFS2 directly on your MTD device (no UBI in the middle).

Quoted 2 lines

I'd really like to be bad block tolerant but
don't know if this makes sense with NOR-Flash (of this size) at all.

You shouldn't need UBI, AFAIR, JFFS2 already deals with wear-leveling/bad-block problems.

Regards,

Boris

#2 lore raw
Quoted 5 lines · Boris Brezillon
Quoted 1 line · On Sat, 19 Nov 2016 22:25:08 +0100 Ralf Schlatterbeck <[email protected]> wrote:

I'm trying to get an ubifs on a 2MB NOR flash.

Quoted 8 lines

Why not putting JFFS2 directly on your MTD device (no UBI in the middle).

Quoted 2 lines

I'd really like to be bad block tolerant but
don't know if this makes sense with NOR-Flash (of this size) at all.

You shouldn't need UBI, AFAIR, JFFS2 already deals with wear-leveling/bad-block problems.

I also need to reinitialize the complete filesystem if something is inconsistent from a known-good source (in that case on a NAND flash). The idea was to ubiformat everything (which preserves wear counters) and re-create the filesystem on top of it (and in the first place I thought I'd use ubifs). I don't think there is a way to re-create a jffs *and* preserving wear counters?

Thanks
Ralf

Signature · 3 lines
Dr. Ralf Schlatterbeck                  Tel:   +43/2243/26465-16
Open Source Consulting                  www:   http://www.runtux.com
Reichergasse 131, A-3411 Weidling       email: [email protected]