init_constants_early: too small LEBs?
I'm trying to get an ubifs on a 2MB NOR flash.
I'm following the usual steps for generating everything from inside the embedded system:
ubiformat /dev/mtd7
ubiattach /dev/ubi_ctrl -m 7 -d 7
ubimkvol /dev/ubi7 -N testvol -s 1968KiB
But when I try to mount I'm getting:
# mount -t ubifs /dev/ubi7_0 /mnt/ mount: mounting /dev/ubi7_0 on /mnt/ failed: Invalid argument
and the kernel log tells me:
Nov 19 21:07:33 board kernel: UBIFS error (pid 1504):
init_constants_early: too small LEBs (3968 bytes), min. is 15360 bytes
Any advice on what to try next?
Should I use a jffs2 on top of UBI using gluebi or run jffs2 on the naked md device instead? I'd really like to be bad block tolerant but don't know if this makes sense with NOR-Flash (of this size) at all.
Thanks
Ralf
Signature · 3 lines
Dr. Ralf Schlatterbeck Tel: +43/2243/26465-16 Open Source Consulting www: http://www.runtux.com Reichergasse 131, A-3411 Weidling email: [email protected]
Hi Ralf,
Quoted 12 lines · On Sat, 19 Nov 2016 22:25:08 +0100 Ralf Schlatterbeck <[email protected]> wrote:
I'm trying to get an ubifs on a 2MB NOR flash.
I'm following the usual steps for generating everything from inside the embedded system:
ubiformat/dev/mtd7
ubiattach/dev/ubi_ctrl-m 7 -d 7
ubimkvol/dev/ubi7-N testvol -s 1968KiBBut when I try to mount I'm getting:
# mount -t ubifs /dev/ubi7_0 /mnt/ mount: mounting /dev/ubi7_0 on /mnt/ failed: Invalid argument
Quoted 8 lines
and the kernel log tells me:
Nov 19 21:07:33 board kernel: UBIFS error (pid 1504):
init_constants_early: too small LEBs (3968 bytes), min. is 15360 bytesAny advice on what to try next?
Should I use a jffs2 on top of UBI using gluebi or run jffs2 on the naked md device instead?
Why not putting JFFS2 directly on your MTD device (no UBI in the middle).
Quoted 2 lines
I'd really like to be bad block tolerant but
don't know if this makes sense with NOR-Flash (of this size) at all.
You shouldn't need UBI, AFAIR, JFFS2 already deals with wear-leveling/bad-block problems.
Regards,
Boris
Quoted 5 lines · Boris Brezillon
Quoted 1 line · On Sat, 19 Nov 2016 22:25:08 +0100 Ralf Schlatterbeck <[email protected]> wrote:
I'm trying to get an ubifs on a 2MB NOR flash.
Quoted 8 lines
Why not putting JFFS2 directly on your MTD device (no UBI in the middle).
Quoted 2 lines
I'd really like to be bad block tolerant but
don't know if this makes sense with NOR-Flash (of this size) at all.You shouldn't need UBI, AFAIR, JFFS2 already deals with wear-leveling/bad-block problems.
I also need to reinitialize the complete filesystem if something is inconsistent from a known-good source (in that case on a NAND flash). The idea was to ubiformat everything (which preserves wear counters) and re-create the filesystem on top of it (and in the first place I thought I'd use ubifs). I don't think there is a way to re-create a jffs *and* preserving wear counters?
Thanks
Ralf
Signature · 3 lines
Dr. Ralf Schlatterbeck Tel: +43/2243/26465-16 Open Source Consulting www: http://www.runtux.com Reichergasse 131, A-3411 Weidling email: [email protected]