Skip to contentSkip to conversation

QCA9880 3x3 80Mhz low performance

DISCUSSION Phyu The 3 participants 10 messages Jan 10, 2017 – Feb 13, 2017 4 messages not in the archive Qualcomm Atheros ATH10K wireless driver

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

Phyu The

author
#1 lore raw

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): 10981E9AB9EA46A1897BE3E5CF661C0F@PhyuThe

A message that is not in the archive (sent off-list or not yet received): [email protected]

author
#5 lore raw

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#6 lore raw

@ben greear. it cannot be cpu related. the ipq8064 has 1.2 ghz and is a very fast arm core. the platform handles 9984 with much higher speed. i got notice of the same issue reported by people on various cpu platforms.

Am 12.01.2017 um 09:15 schrieb Phyu The:

Quoted 68 lines

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 17 lines
Mit freundlichen Grüssen / Regards

Sebastian Gottschall / CTO

NewMedia-NET GmbH - DD-WRT
Firmensitz:  Berliner Ring 101, 64625 Bensheim
Registergericht: Amtsgericht Darmstadt, HRB 25473
Geschäftsführer: Peter Steinhäuser, Christian Scheele
http://www.dd-wrt.com
email: [email protected]
Tel.: +496251-582650 / Fax: +496251-5826565


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#7 lore raw

Hello!

We ran some more tests using our x86 based platforms with 9880 NICs and 9984 NICs acting as both AP and Station. This is in an isolation chamber, wired up with SMA cables and variable attenuator, in as perfect of a condition as we can manage.

First, here is LANforge acting as AP and station devices, using QCA9880 3x3 hardware:

http://www.candelatech.com/images/data-comp-01-13-2017-144224-lf-ap.png

And with 9984 systems:

http://www.candelatech.com/images/data-comp-01-19-2017-1706-lf-ap-sta-9984.png

In case you read closely and wonder, 'Armageddon' is our modified version of pktgen.

Thanks,
Ben

Quoted 74 lines · Sebastian Gottschall

@ben greear. it cannot be cpu related. the ipq8064 has 1.2 ghz and is a very fast arm core. the platform handles 9984 with much higher speed. i got notice of the same issue reported by people on various cpu platforms.

Am 12.01.2017 um 09:15 schrieb Phyu The:

Quoted 68 lines

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author
#8 lore raw

Dear Ben,

According to your test result of QCA9880 3x3, what could be the low performance issue at my side IPQ8064+QCA9880 with Ath10k? Is it really CPU related problem on WPQ864?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, January 21, 2017 4:24 AM
To: Sebastian Gottschall ; Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

Hello!

We ran some more tests using our x86 based platforms with 9880 NICs and 9984 NICs acting as both AP and Station. This is in an isolation chamber, wired up with SMA cables and variable attenuator, in as perfect of a condition as we can manage.

First, here is LANforge acting as AP and station devices, using QCA9880 3x3 hardware:

http://www.candelatech.com/images/data-comp-01-13-2017-144224-lf-ap.png

And with 9984 systems:

http://www.candelatech.com/images/data-comp-01-19-2017-1706-lf-ap-sta-9984.png

In case you read closely and wonder, 'Armageddon' is our modified version of pktgen.

Thanks,
Ben

Quoted 75 lines · Sebastian Gottschall

@ben greear. it cannot be cpu related. the ipq8064 has 1.2 ghz and is a very fast arm core. the platform handles 9984 with much higher speed. i got notice of the same issue reported by people on various cpu platforms.

Am 12.01.2017 um 09:15 schrieb Phyu The:

Quoted 68 lines

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 14 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k 


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#9 lore raw

I don't know. I would first suggest that you try an x86 platform with powerful CPU in your own test environment. Possibly we are just using a better isolation chamber or have some other advantage in our environment or test setup.

If you can reproduce our good results with x86 in your setup, then you can be more sure it is something to do with your particular platform.

Thanks,
Ben

Quoted 110 lines · Phyu The

Dear Ben,

According to your test result of QCA9880 3x3, what could be the low performance issue at my side IPQ8064+QCA9880 with Ath10k? Is it really CPU related problem on WPQ864?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, January 21, 2017 4:24 AM
To: Sebastian Gottschall ; Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

Hello!

We ran some more tests using our x86 based platforms with 9880 NICs and 9984 NICs acting as both AP and Station. This is in an isolation chamber, wired up with SMA cables and variable attenuator, in as perfect of a condition as we can manage.

First, here is LANforge acting as AP and station devices, using QCA9880 3x3 hardware:

http://www.candelatech.com/images/data-comp-01-13-2017-144224-lf-ap.png

And with 9984 systems:

http://www.candelatech.com/images/data-comp-01-19-2017-1706-lf-ap-sta-9984.png

In case you read closely and wonder, 'Armageddon' is our modified version of pktgen.

Thanks,
Ben

Quoted 74 lines · Sebastian Gottschall

@ben greear. it cannot be cpu related. the ipq8064 has 1.2 ghz and is a very fast arm core. the platform handles 9984 with much higher speed. i got notice of the same issue reported by people on various cpu platforms.

Am 12.01.2017 um 09:15 schrieb Phyu The:

Quoted 68 lines

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 8 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author
#10 lore raw

Dear Ben,

I tested same set up with QCA driver, I can achieve 984Mbps. With Ath10k driver, throughput stuck at 640Mpbs. Can you give me any suggestion?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, February 11, 2017 12:14 AM
To: Phyu The ; Sebastian Gottschall ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

I don't know. I would first suggest that you try an x86 platform with powerful CPU in your own test environment. Possibly we are just using a better isolation chamber or have some other advantage in our environment or test setup.

If you can reproduce our good results with x86 in your setup, then you can be more sure it is something to do with your particular platform.

Thanks,
Ben

Quoted 111 lines · Phyu The

Dear Ben,

According to your test result of QCA9880 3x3, what could be the low performance issue at my side IPQ8064+QCA9880 with Ath10k? Is it really CPU related problem on WPQ864?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, January 21, 2017 4:24 AM
To: Sebastian Gottschall ; Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

Hello!

We ran some more tests using our x86 based platforms with 9880 NICs and 9984 NICs acting as both AP and Station. This is in an isolation chamber, wired up with SMA cables and variable attenuator, in as perfect of a condition as we can manage.

First, here is LANforge acting as AP and station devices, using QCA9880 3x3 hardware:

http://www.candelatech.com/images/data-comp-01-13-2017-144224-lf-ap.png

And with 9984 systems:

http://www.candelatech.com/images/data-comp-01-19-2017-1706-lf-ap-sta-9984.png

In case you read closely and wonder, 'Armageddon' is our modified version of pktgen.

Thanks,
Ben

Quoted 75 lines · Sebastian Gottschall

@ben greear. it cannot be cpu related. the ipq8064 has 1.2 ghz and is a very fast arm core. the platform handles 9984 with much higher speed. i got notice of the same issue reported by people on various cpu platforms.

Am 12.01.2017 um 09:15 schrieb Phyu The:

Quoted 68 lines

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 14 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k 


_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
#11 lore raw

I would try to narrow down where the performance issue happens.

So, for instance, could you run the exact same ath10k firmware (and board.bin, etc) that you are using in LEDE with the QCA driver? That would determine if it is firmware related or not.

Can you compile just the QCA driver into LEDE to see if that makes a difference?

You are using the exact same networking setup in all cases?

Thanks,
Ben

Quoted 136 lines · Phyu The

Dear Ben,

I tested same set up with QCA driver, I can achieve 984Mbps. With Ath10k driver, throughput stuck at 640Mpbs. Can you give me any suggestion?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, February 11, 2017 12:14 AM
To: Phyu The ; Sebastian Gottschall ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

I don't know. I would first suggest that you try an x86 platform with powerful CPU in your own test environment. Possibly we are just using a better isolation chamber or have some other advantage in our environment or test setup.

If you can reproduce our good results with x86 in your setup, then you can be more sure it is something to do with your particular platform.

Thanks,
Ben

Quoted 110 lines · Phyu The

Dear Ben,

According to your test result of QCA9880 3x3, what could be the low performance issue at my side IPQ8064+QCA9880 with Ath10k? Is it really CPU related problem on WPQ864?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, January 21, 2017 4:24 AM
To: Sebastian Gottschall ; Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

Hello!

We ran some more tests using our x86 based platforms with 9880 NICs and 9984 NICs acting as both AP and Station. This is in an isolation chamber, wired up with SMA cables and variable attenuator, in as perfect of a condition as we can manage.

First, here is LANforge acting as AP and station devices, using QCA9880 3x3 hardware:

http://www.candelatech.com/images/data-comp-01-13-2017-144224-lf-ap.png

And with 9984 systems:

http://www.candelatech.com/images/data-comp-01-19-2017-1706-lf-ap-sta-9984.png

In case you read closely and wonder, 'Armageddon' is our modified version of pktgen.

Thanks,
Ben

Quoted 74 lines · Sebastian Gottschall

@ben greear. it cannot be cpu related. the ipq8064 has 1.2 ghz and is a very fast arm core. the platform handles 9984 with much higher speed. i got notice of the same issue reported by people on various cpu platforms.

Am 12.01.2017 um 09:15 schrieb Phyu The:

Quoted 68 lines

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 7 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
author
#12 lore raw

Dear Ben,

Kindly see attached that I run with Ixchariot used exact same configuration and set up environment.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Monday, February 13, 2017 1:13 PM
To: Phyu The ; Sebastian Gottschall ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

I would try to narrow down where the performance issue happens.

So, for instance, could you run the exact same ath10k firmware (and board.bin, etc) that you are using in LEDE with the QCA driver? That would determine if it is firmware related or not.

Can you compile just the QCA driver into LEDE to see if that makes a difference?

You are using the exact same networking setup in all cases?

Thanks,
Ben

Quoted 137 lines · Phyu The

Dear Ben,

I tested same set up with QCA driver, I can achieve 984Mbps. With Ath10k driver, throughput stuck at 640Mpbs. Can you give me any suggestion?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, February 11, 2017 12:14 AM
To: Phyu The ; Sebastian Gottschall ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

I don't know. I would first suggest that you try an x86 platform with powerful CPU in your own test environment. Possibly we are just using a better isolation chamber or have some other advantage in our environment or test setup.

If you can reproduce our good results with x86 in your setup, then you can be more sure it is something to do with your particular platform.

Thanks,
Ben

Quoted 111 lines · Phyu The

Dear Ben,

According to your test result of QCA9880 3x3, what could be the low performance issue at my side IPQ8064+QCA9880 with Ath10k? Is it really CPU related problem on WPQ864?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, January 21, 2017 4:24 AM
To: Sebastian Gottschall ; Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

Hello!

We ran some more tests using our x86 based platforms with 9880 NICs and 9984 NICs acting as both AP and Station. This is in an isolation chamber, wired up with SMA cables and variable attenuator, in as perfect of a condition as we can manage.

First, here is LANforge acting as AP and station devices, using QCA9880 3x3 hardware:

http://www.candelatech.com/images/data-comp-01-13-2017-144224-lf-ap.png

And with 9984 systems:

http://www.candelatech.com/images/data-comp-01-19-2017-1706-lf-ap-sta-9984.png

In case you read closely and wonder, 'Armageddon' is our modified version of pktgen.

Thanks,
Ben

Quoted 75 lines · Sebastian Gottschall

@ben greear. it cannot be cpu related. the ipq8064 has 1.2 ghz and is a very fast arm core. the platform handles 9984 with much higher speed. i got notice of the same issue reported by people on various cpu platforms.

Am 12.01.2017 um 09:15 schrieb Phyu The:

Quoted 68 lines

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 7 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k 

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

#13 lore raw

Looks like it is driver and/or OS related then, not related to firmware.

So, maybe next see if you can get the ath10k driver to work in the QCA OS, or get the QCA driver to work in the LEDE OS (replacing ath10k driver).

Thanks,
Ben

Quoted 162 lines · Phyu The

Dear Ben,

Kindly see attached that I run with Ixchariot used exact same configuration and set up environment.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Monday, February 13, 2017 1:13 PM
To: Phyu The ; Sebastian Gottschall ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

I would try to narrow down where the performance issue happens.

So, for instance, could you run the exact same ath10k firmware (and board.bin, etc) that you are using in LEDE with the QCA driver? That would determine if it is firmware related or not.

Can you compile just the QCA driver into LEDE to see if that makes a difference?

You are using the exact same networking setup in all cases?

Thanks,
Ben

Quoted 136 lines · Phyu The

Dear Ben,

I tested same set up with QCA driver, I can achieve 984Mbps. With Ath10k driver, throughput stuck at 640Mpbs. Can you give me any suggestion?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, February 11, 2017 12:14 AM
To: Phyu The ; Sebastian Gottschall ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

I don't know. I would first suggest that you try an x86 platform with powerful CPU in your own test environment. Possibly we are just using a better isolation chamber or have some other advantage in our environment or test setup.

If you can reproduce our good results with x86 in your setup, then you can be more sure it is something to do with your particular platform.

Thanks,
Ben

Quoted 110 lines · Phyu The

Dear Ben,

According to your test result of QCA9880 3x3, what could be the low performance issue at my side IPQ8064+QCA9880 with Ath10k? Is it really CPU related problem on WPQ864?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Saturday, January 21, 2017 4:24 AM
To: Sebastian Gottschall ; Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

Hello!

We ran some more tests using our x86 based platforms with 9880 NICs and 9984 NICs acting as both AP and Station. This is in an isolation chamber, wired up with SMA cables and variable attenuator, in as perfect of a condition as we can manage.

First, here is LANforge acting as AP and station devices, using QCA9880 3x3 hardware:

http://www.candelatech.com/images/data-comp-01-13-2017-144224-lf-ap.png

And with 9984 systems:

http://www.candelatech.com/images/data-comp-01-19-2017-1706-lf-ap-sta-9984.png

In case you read closely and wonder, 'Armageddon' is our modified version of pktgen.

Thanks,
Ben

Quoted 74 lines · Sebastian Gottschall

@ben greear. it cannot be cpu related. the ipq8064 has 1.2 ghz and is a very fast arm core. the platform handles 9984 with much higher speed. i got notice of the same issue reported by people on various cpu platforms.

Am 12.01.2017 um 09:15 schrieb Phyu The:

Quoted 68 lines

Dear Ben,

Thanks for your reply and suggestion.

I have tried as your suggestion to test IPQ8064+QCA9880 with Ath10k CT firmware/driver to run throughput UDP/TCP. Unfortunately, I could not be able to see throughput improvement. Could you please suggest what may cause low throughput?

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Thursday, January 12, 2017 12:59 AM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

We have not done a lot of testing in AP mode, but when using 9880 3x3 compex NICs in our 2U rackmounts (high end Intel E5 processors), and with CT firmware/drivers, we see near 950Mbps UDP download in station mode. I think we were a bit slower in AP mode, but not that much.

Are you testing TCP or UDP traffic?

http://www.candelatech.com/images/data-comp-07-20-2016-1147-with-labels.png

Have you tried normal STA/AP mode instead of WDS?

Maybe you are CPU bound on your platform?

Thanks,
Ben

Quoted 34 lines · Phyu The

Dear Ben,

I configured AP_WDS and Sta_WDS mode, channel 149, 11ac, 3x3, 80MHz and without encryption. I used 2 RF boxes with 3 adjustable attenuators running throughput by Ixchairot to get best performance. However, throughput seems limited to 640Mbps. Kindly see attached for your reference for more details.

thanks,
Phyuthe

-----Original Message----- From: Ben Greear
Sent: Tuesday, January 10, 2017 10:37 PM
To: Phyu The ; [email protected]
Subject: Re: QCA9880 3x3 80Mhz low performance

You should provide a lot more information about how you configured and tested the system, including traffic generator and RF environment, etc.

Thanks,
Ben

Quoted 13 lines · Phyu The

Dear Sir,

I tested performance throughput test used WPQ864 + QCA9880 11ac 80MHz is 640Mbps that is very low since theoretical data rate is 1300Mbps. It should be at least 866Mbps. Could you please suggest me how to get better performance?

thanks,
Phyuthe

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k

Signature · 7 lines
Ben Greear <[email protected]>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k